RH Baby&child F0035-7 User manual

Made in Vietnam
Distributed in the U.S.A by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Model No: F0035 - 7
DRAKE PANEL TODDLER KIT
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
Page 1 of 6
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool
dry place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included).
NOTE: It may be easier to assemble productwith two people.
NOTE:When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After crib is completely assembled,
return to each bolt and tighten.

IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could result in
serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may strangle
a child.
The mattress intended for use on the bed shall be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310 mm) in length, 271/4
inches (690 mm) in width and 4 inches (100 mm) in thickness, not
exceeding 6 inches (152 mm) in thickness.
If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50 lbs (22.7 kg).
WARNING: ENTRAPMENT/ STRANGULATION HAZARD
Page 2 of 6

ASSEMBLY INSTRUCTIONS
Page 3 of 6
PARTS INCLUDED:
D
HARDWARE INCLUDED:
[1] TODDLER RAIL
CRIB ( Sold separately)
D
6
7
8
9
Long Bolts 5/16” x 2”
Small Bolts 5/16” x 3/4”
4 pcs.
Spring Washer 5/16”
2 pcs.
6 pcs.
NO. ITEM DESCRIPTIONQTY.
Allen Key 4mm 1 pc.

Remove Stationary Side Rail (B) from the
crib by carefully unscrewing and removing
the (4pcs) Long bolts with spring washer
on Left /Right sides of the Stationary Side
Rail (B) using Allen Key (9).
Page 4 of 6
ASSEMBLY INSTRUCTIONS
STEP 1:
If mattress support is not in the lowest
position, loosen all tightened bolts from
side frames. Spread front of crib open
enough to remove mattress support (C),
and move it to the lowest position.
STEP 2:
Note: The Mattress support (C) must be at
the lowest level for a toddler bed.
A
A
B
A
B
9
4x
B
C
4x
A
Highest
level
Middle
level
Lowest
level
C
9

Page 5 of 6
ASSEMBLY INSTRUCTIONS
STEP 3:
Position the Toddler Rail (D) between the
Headboard/ Footboard (A) and align the holes.
Attach the Toddler Rail (D) to the crib
by securing with Long Bolts (6), Spring
Washers (8), and tighten with Allen
Key (9).
STEP 4:
A
DA
D
6
8
A
D
9
4x

Page 6 of 6
STEP 5:
When converting the crib to toddler bed, the
Small Bolt (7), and Spring Washer (8) should
be inserted in the upper holes of the Side
Frame (A) and tighten with the Allen Key (9).
After crib is completely assembled, return to each
bolt and tighten to snug fit. DO NOT over tighten.
WARNING:
A
A
A
2x
89
7
ASSEMBLY INSTRUCTIONS