RH Teen RIDLEY TASK SCONCE User manual

RIDLEY TASK SCONCE – ASSEMBLY INSTRUCTIONS
PARTS ENCLOSED:
(A) Wall Anchors (2) (G) ON/OFF Rotating
(B) Mounting Plate (1) Switch (1)
(C) Wall Screws (2) ( ) Plate Screws (3)
(D) Top Cord Cover (1) (I) Shade (1)
(E) Plug (1) (J) LED Bulb (1)
(F) Bottom Cord Cover (1) (K) Shade Joint (1)
(L) Back Plate (1)
RIDLEY TASK SCONCE
Plug-In Installation
IMPORTANT SAFETY INSTRUCTIONS:
The fixture can be used as a plug-in or a fixed unit when used with the appropriate
conversion kit. For your safety, this sconce is equipped with a 3-pronged polarized
plug. If the plug does not fit securely into your outlet, do not force it – contact a
professional electrician. Use the plug with an extension cord only if it can be fully
inserted into the cord's socket. Never alter the plug in any way.
This fixture has been rated for up to (1) 4w max Type T LED bulb (MODEL NO.: T8-4,
included) or (1) 40w max Type T incandescent bulb (not included).To avoid the risk of
fire, do not exceed the recommended wattage.
WARNIN S:
All wires are connected. When unpacking, be careful not to pull wires, as a bad
connection may result. Do not connect electricity until the fixture is fully
assembled. To reduce the risk of fire, electrical shock, or personal injury, always
turn off and unplug fixture and allow it to cool prior to replacing lightbulb.
Do not touch bulb when fixture is turned on or look directly at lit bulb.
Keep flammable materials away from lit bulb.
DO NOT REMOVE T E CARDBOARD INSULATOR SURROUNDING T E SOCKET.
T IS PRODUCT IS NOT A TOY AND AS NO PLAY VALUE.
WARNIN : STRAN ULATION HAZARD
PLU -IN ASSEMBLY INSTRUCTIONS:
1. Carefully remove all parts from the box and remove all plastic coverings.
2. Drill 2 holes in the wall that align with the holes on the mounting plate of the lamp
(B) and insert wall anchors (A).
3. Place mounting plate (B) onto the wall anchors (A), then screw wall screws (C)
into anchors.
4. Attach the back plate (L) to the mounting plate (B) and use the plate
screws ( ) to secure.
5. Screw the top cord cover (D) into the hole located on the bottom of the back
plate (L).
6. Screw the bottom cord cover (F) into the top cord cover (D).
7. Insert (1) LED bulb (J) into the threaded socket.
8. Adjust the shade joint (K) to get your desired angle for the shade (I).
9. Insert plug (E) into proper electrical outlet and rotate ON/OFF switch (G) to test
fixture.
CARE INSTRUCTIONS:
To clean, use a soft, dry cloth.
Do not use polishes or cleaners on the fixture.
Keep cord at least 3 feet away from cribs, bassinets, and toddler beds.
Keep out of reach of children under 3 years of age.

PARTS ENCLOSED:
(A) Ground Wire Screw (1) (G) Plastic Wire
(B) Mounting Plate (1) Connector(3)
(C) Mounting Plate Screws (2) ( ) Shade (1)
(D) Thread Plug Screw (I) LED Bulb (1)
(E) ON/OFF Rotating Switch (1) (J) Shade Joint (1)
(F) Plate Screws (3) (K) Back Plate (1)
RIDLEY TASK SCONCE
Direct-Wire Installation
IMPORTANT SAFETY INSTRUCTIONS:
The fixture can be used as a plug-in or a fixed unit when used with the appropriate
conversion kit. For your safety, this sconce is equipped with a 3-pronged polarized
plug. If the plug does not fit securely into your outlet, do not force it – contact a
professional electrician. Use the plug with an extension cord only if it can be fully
inserted into the cord's socket. Never alter the plug in any way.
This fixture has been rated for up to (1) 4w max Type T LED bulb (MODEL NO.: T8-4,
included) or (1) 40w max Type T incandescent bulb (not included).To avoid the risk
of fire, do not exceed the recommended wattage.
WARNIN S:
All wires are connected. When unpacking, be careful not to pull wires, as a
bad connection may result. Do not connect electricity until your sconce is fully
assembled. To reduce the risk of fire, electrical shock, or personal injury,
turn off and unplug fixture and allow it to cool prior to replacing lightbulb.
Do not touch bulb when fixture is turned on or look directly at lit bulb.
Keep flammable materials away from lit bulb.
RIDLEY TASK SCONCE – ASSEMBLY INSTRUCTIONS
DIRECT-WIRE ASSEMBLY INSTRUCTIONS:
1. Carefully remove all parts from the box and remove all plastic coverings.
2. S UT OFF T E MAIN ELECTRICAL SUPPLY FROM T E MAIN FUSE BOX /
CIRCUIT BREAKER.
3. Cut the plug from the end of the electrical cord. From the back side of the fixture,
pull the electrical cord through the exit hole at the bottom of the back plate (K).
Then thread plug screw (D) into the hole vacated by the cord.
4. Cut the cord to the desired length (at least 6" from the back plate) to
make a "J BOX" connection.
5. Guide the wiring from the outlet box through the center hole in the mounting plate
(B).
6. Attach the mounting plate (B) to the outlet box using the mounting plate screws
(C) to secure.
7. Attach the ground wire (usually green or bare wire) from the fixture to the
ground junction box wire from the outlet box (usually green or bare wire). Or
wrap the ground wire around the green ground wire screw (A).
8.Connect the hot wire to the hot junction box wire (usually black) with a wire
connector (G) and wrap the connection with electrical tape. Connect the neutral
wire to the neutral junction box wire (usually white) with a plastic wire connector
(G) and wrap the connection with electrical tape.
9. Attach the back plate (K) to the mounting plate (B) and use the plate screw (F) to
secure the back plate.
10. Insert (1) LED bulb (I) into the threaded socket.
11. Restore power to the junction box and rotate ON/OFF switch (E) to test fixture.
12. Installation is complete.
CARE INSTRUCTIONS:
To clean, use a soft, dry cloth.
Do not use polishes or cleaners on the fixture.