RH Teen COLBIN WIDE BOOKCASE User manual

C O L B I N W I D E B O O K C A S E I N S T R U C T I O N S
5Metal Bracket 2 pcs.
6Clevis Pin 2 pcs.
7
8Hair Pin 2 pcs.
Steel Aircraft cable 1 pc.
9
10
Short Screw 2 pcs.
2 pcs.
NO. ITEM DESCRIPTION QTY.
Long Screw
Handle 3 pcs.
Philip head Bolt 6 pcs.
2
1
1
2
Driver
FIGURE 1
Shelf holder
Round head screws
(M4 x 15mm)
8 pcs.
8 pcs.
3
4
PARTS INCLUDED
A [1] BOOKCASE
B [2] REMOVABLE SHELF PANELS
FIGURE 2
Leveler
ASSEMBLY INSTRUCTIONS
1. For packing purpose, the drawer handles were reversed or removed and put in hardware
bag. Attach the handles (2) to the drawer of bookcase by using the Phillips head bolts (1)
provided. Repeat this steps to attach handle for other drawers.Refer to FIGURE 1.
2. Check the furniture leveling, if it does not seat level, adjust the leveler on the bottom of
the base, as per illustrated in FIGURE 2.
3. Apply glue on the felt pads (11) then stick them underneath the levelers. See FIGURE 2.
WARNING
Use product on carpet or apply optional felt pads to help protect floors.
Do not pull or push product on the floor.
Felt Pad 4 pcs.
11
Optional
felt pad
Toggle bolt 2 sets
12
Page 1 of 3

3
4
4. Install the metal shelf holders (3), set the removable shelf panels (B) on the shelf holders then fix them together by
inserting screws (4) provided. See FIGURE 3.
FIGURE 3
DRYWALL W/STUDS DRYWALL W/O STUDS
FIGURE A FIGURE B
ASSEMBLY INSTRUCTIONS BY WALL TYPE :
• DRYWALL WITH STUDS: Use screws to affix to studs, and
use hollow wall anchors and screws to affix to drywall. See
FIGURE A.
• DRYWALL WITHOUT STUDS: Use toggle bolt and screws to
affix to drywall. See FIGURE B.
C O L B I N W I D E B O O K C A S E I N S T R U C T I O N S
Page 2 of 3

FURNITURE TIPPING RESTRAINT INSTRUCTIONS
Young children may be injured by tipping furniture. The use of a tipping restraint is
highly recommended.
When properly installed, this restraint could provide protection against the
unexpected tipping of furniture due to small tremors, bumps or climbing. We
recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a substitute for proper adult
supervision.
ANTI-TIP-KIT INSTALLATION INSTRUCTION
Wall
10
9
8
7
6
5
1. Attach mounting brackets (5) near the middle-top back edge
of the furniture piece by inserting the shorter screws (9).
2. Determine the final position of the furniture piece. Mark
locations on the wall approximately 2" below the brackets
mounted to the back of the furniture.
3. Attach the second brackets by inserting the longer screw (10)
or toggle bolt (12) or plastic anchor (DEPEND ON YOUR
WALL TYPE) through the bracket and into the wall.
4. Place the furniture so that the brackets on the back edge are
in line with the brackets in the wall.
5. Insert the clevis pin (6) through holes on brackets and hole
on steel aircraft cable (7). Using hair pin (8) to go through
small hole on clevis pin (6) to lock it.
6. Repeat above step to attach the end of air craft cable (7) to
the bracket on the wall.
7. Check to make sure the steel aircraft cable are securely
laced and locked to the brackets.
WARNING: Always mount metal brackets to solid wood of furniture.
Do not attach to plywood of back panels. Always locate and attach to studs.
Do not depend on wall anchors.
CARE INSTRUCTIONS
1. Dust often using a clean, soft, dry and lint-free cloth.
2. Blot spills immediately and wipe with a clean, damp, cloth.
3. We do not recommend the use of chemical cleansers,
abrasives or furniture polish on our lacquered finish.
IMPORTANT SAFETY INSTRUCTIONS
1. Please read all instructions carefully before assembling.
2. For your safety, assembly by two or more adults is strongly recommended.
3. Keep instructions for future use.
4. Use only vendor supplied hardware to assemble. Using unauthorized
hardware could jeopardize the structural integrity of the item.
COLBIN WIDE BOOKCASE INSTRUCTIONS
Page 3 of 3