RH Teen LAGUNA FULL LOFT BED User manual

L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
All RH loft and bunk beds are designed to meet the highest safety
standards and comply with all U.S. and Canadian loft and bunk bed regulations.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include the
product model number, color, and a brief description of the part. Or call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth. Blot spills immediately and wipe
with a clean, damp cloth. If the bed is to be stored, store in a cool, dry place and carefully package all original hardware to protect from loss.
TOOLS NEEDED
Allen key (included)
Wrench (included)
Screwdriver (not included)
Note: Two people are recommended for assembly.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After bed is completely assembled, return to each bolt and tighten.
Use wax or soap on all bolts to facilitate assembly.
18
/

L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
IMPORTANT SAFETY INFORMATION
1. Follow the information on the WARNING label attached to the loft and on
the packaging.
2. Always use the specified mattress size, mattress support, or both to help
prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of
guardrails on the loft.
4. Do not allow children under 6 years of age to use the loft.
5. Prohibit more than one person on the loft.
6. Periodically check and ensure that the guardrails, ladder, and other
components are in their proper position, free from damage, and that all
connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the loft.
9. Do not use substitute parts. Contact RH for replacement parts.
10.Use of a night light may provide added safety precaution for a child using
the loft.
11.Use guardrails on both sides of the loft.
12.If the bed will be placed next to a wall, the guardrail that runs the full length
of the bed should be placed against the wall to prevent entrapment between
the bed and the wall.
13. The use of a water flotation mattress is prohibited.
14.STRANGULATION HAZARD - Never attach or hang items to any part of the
bed that are not designed for use with the bed, such as hooks, belts, and
jump ropes.
15.Keep these instructions for future reference.
16.DO NOT remove warning label from bed.
WARNING
DO NOT REMOVE THIS LABEL
TO HELP PREVENT SERIOUS OR FATAL
INJURIES FROM ENTRAPMENT OR FALLS:
1. Never allow a child under 6 years of age on the loft.
2. Use a mattress that is 53"W x 75"L x 6''H on Full loft
bunk.
3. Ensure height of mattress does not exceed 6" and
mattress is at least 5" below upper edge of guardrails.
4. Use guardrails on both sides of the loft.
5. Use ladder for entering and leaving the loft.
6. Prohibit horseplay on or under bed.
7. Do not allow more than one person on the loft.
8. If the bed will be placed next to a wall, be sure the
adjacent guardrails run the full length of the bed.
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bed that
are not designed for use with the bed, such as hooks,
belts, and jump ropes.
28
/

PARTS INCLUDED
A [1] HEADBOARD
B [1] FOOTBOARD
C [1] LOWER SIDE RAIL
D [2] UPPER SIDE RAILS
E [5] BED SLATS
F [2] PLATFORM PANELS
G [1] LONG GUARDRAIL
H [1] SHORT GUARDRAIL
I [1] LADDER
COMPONENT IDENTIFICATION AND HARDWARE
NO. ITEM DESCRIPTION QTY.
1Threaded Rod 12 pcs.
2Curved Washer 12 pcs.
3Lock Washer 12 pcs.
4
5Wrench 1 pc.
Hex Nut 12 pcs.
Phillips Flathead Screw
(M4x20mm) 22 pcs.
Round-head Screw
(M4x25mm) 42 pcs.
Metal Bracket 3 pcs.
Concealed Metal Bracket 2 pcs.
Phillips Flathead Screw
(M3x15mm) 4 pcs.
NO. ITEM DESCRIPTION QTY.
6
7
8
9
NO. ITEM DESCRIPTION QTY.
10
B
AC
D
E
F
F
D
G
H
I
L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
Phillips Screwdriver 1 pc.
15
NO. ITEM DESCRIPTION QTY.
TOOLS REQUIRED (NOT INCLUDED)
NO. ITEM DESCRIPTION QTY.
11 4 pcs.
12 4 pcs.
13 4 pcs.
14 1 pc.
Allen Bolt
Plain Washer
Allen Key
Lock Washer
38
/

ASSEMBLY INSTRUCTIONS
1. Lay the headboard (A) and footboard (B) on a flat surface.
2. Attach the long guardrail (G) to the headboard (A) and the short guardrail (H) to the footboard (B). Refer to FIGURE 1.
3. Attach the threaded rods (1) into the fixed nuts in the post of the headboard/footboard by turning them manually. See FIGURE 2 and FIGURE 3.
NOTE: The shortguard rail can be installed at either end of the headboard or footboard depending on your desired ladder location. When short
guardraill (H) is installed into the left side of the headboard or footboard, refer to option A and B. If, the guardrail is installed into the right side of
the headboard or footboard, refer to option C and D.
6
FIGURE 1
OPTION A OPTION B
OPTION C OPTION D
FIGURE 2
1
FIGURE 3
1
Fig.1
Fig.2
Fig.3
Fig.1
Fig.2
Fig.3
L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
IMPORTANT
These bed parts can be cumbersome and heavy. Two people are therefore recommended for assembly to prevent personal injury and ensure the bed
parts are not damaged during the assembly process.
48
/

4. Attach the lower side rail (C) to the headboard (A/G) as shown in FIGURE 4.
5. Bring the upper side rail (D) in upright position and align the threaded rods on the headboard to the corresponding holes in the end of the upper side
rail. Attach the upper side rail to the headboard, as shown in FIGURE 5. KEEP HOLDING THE SIDE RAIL DURING NEXT STEP.
6. Repeat step 5 to attach the other upper side rail to the headboard. KEEP HOLDING BOTH UPPER SIDE RAILS DURING NEXT STEP.
7. Align the threaded rods on the footboard (B/H) to the corresponding holes at the end of lower side rail (C) and upper side rails (D). Align the locator
pins on the end of the side rails to the corresponding holes in the footboard. Insert the footboard into the side rails.
8. Repeat steps 4, 5 and 6 to attach the side rails to the footboard.
Fig.5
Fig.5
Fig.4
C
D
D
FIGURE 4
FIGURE 5
B
L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
2
3
4
1
13
12
11
14
58
/

9. Attach the metal bracket (7) onto the side rails and guardrails. Insert screws (6) provided to pass through holes on the metal bracket (7) to the
pre-drilled holes on side rails and guardrails. Refer to FIGURE 6.
10. Set the bed slats (E) into the loft. Secure each slat by using screws (10) provided. See FIGURE 7.
11. For shipping purposes, both of concealed metal brackets (8) were removed and placed in the hardware package. The headboard and footboard
have pre-drilled holes where the ladder will be installed. Determine the desired location of the ladder and install the concealed metal bracket (8)
into the pre-drilled holes and secure it with the Phillips screws (9) provided. Refer to FIGURE 8.
7
6
FIGURE 6
9
FIGURE 8
10
FIGURE 7
L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
68
/

12. Hook the ladder (I) on the footboard and simultaneously align the metal concealed bracket on the ladder with the bracket on the footboard.
Use screws (6) provided to affix the top of ladder with footboard as shown in FIGURE 9 and FIGURE 10.
13. Place the platform panels (H) on the upper bed, then affix them with screws (10). See FIGURE 11.
6
no screw
FIGURE 10
FIGURE 9
10
FIGURE 11
F
F
L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
78
/

LOFT BED MATTRESS DIAGRAM
5'' MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARDRAIL
6'' MAXIMUM
MATTRESS HEIGHT
PLATFORM PANEL SLAT SUPPORT
SIDE RAIL
GUARDRAIL
L A G U N A F U L L L O F T B E D - A S S E M B L Y I N S T R U C T I O N S
14. MATTRESS INSTALLATION
MATTRESS SPECIFICATION:
The following mattress and foundation sizes are specified for use with this loft bed.
Mattress: 53''W x 75''L x 6''H on Full loft bed.
**Note: TOP MATTRESS AND PLATFORM MUST NOT EXCEED 6'' TOTAL HEIGHT.
Be sure to adhere to these MATTRESS SPECIFICATIONS in order to avoid the possibility of falling or entrapment.
THESE SPECIFICATIONS MUST BE STRICTLY FOLLOWED!
88
/