RH Teen 355-80 User manual

All Restoration Hardware
bunk beds are designed to
meet the highest safety
standards and comply with
all U.S. and Canadian Bunk
Bed regulations.
Page 1 of 13

Distributed in the U.S.A by:
Restoration Hardware
11640 Harrel St, SuiteBMira Loma
CA 91752
rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada Inc.
1500-1055 West Georgia Street,
Vancouver, British Columbia V6E
4N7
WARNING:
Read all Instructions before
assembling this product KEEP
INSTRUCTIONS FOR FUTURE
USE.
CUSTOMER SERVICE.
If you are missing parts or have any questions about this product, contact us first. You can also order
parts by writing to the address above. Include the product model number, color, and a brief descrip-
tion of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT use abrasive chemicals for cleaning. Dust often using aclean, soft dry cloth. Rinse and dry
thoroughly. If the Bunk bed is to be stored, store in a cool dry place and carefully package all origi-
nal hardware to protect from loss.
Page 2 of 13
Restoration Hardware Baby & Child
11640 Harrel St, Suite B Mira Loma CA 91752
rhbabyandchild.com
Made in Vietnam
Assembly Instructions Callum Storage Twin Bunk
Model No:
#355-80 Callum Storage Twin Bunk

IMPORTANT SAFETY INFORMATION FOR BUNK BED:
1. Follow the information onthe WARNINGS appearing on the upperbunk end structure and onthe
carton. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood
of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under6years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on thebed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts
10. Use of a night light may provide added safety precaution for a child using theupper bunk.
11. Use guardrails on both sides of theupper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use withthe bed: for example, but not limited to, hooks,belts,and jump ropes.
15. Keep these instructions for future reference.
Page 3 of 13
CAL L UM S T O R A GE T WIN BU N K

Parts Identification
Please note, Headboard and Footboard are interchangeable and can be installed on either end of bunk.
Page 4 of 13
(A) Headboard/ Footboard (x2 pieces)
(C) Front/ Back Guard Rails (x2 pieces) (D) Long Side Guard Rail (x1 piece)
(F) Bottom Side Rail (x1 piece)
(H) Top Platform Panels (x2 pieces)
(J) Slat Roll (x1 set)
(E) Short Side Guard Rail (x1 piece)
(G) Stretcher Bars (x4 pieces)
(I) Storage Box (x1 set)
(B) Ladder (x1 piece)
CALLUM STORAGE TWIN BUNK

ASSEMBLY INSTRUCTIONS:
Note:
- Bed must be assembled by at least two people.
- Please read instructions carefully before assembling bed.
- Use the parts and fittings list to identify each component.
- Keep all packing materials until assembly is complete to avoid loss of smaller parts.
- Do not completely tighten all bolts until all steps are finished.
Page 5 of 13
HARDWARE INCLUDED:
Phillips Head Screwdriver
(Not included)
TOOLS NEEDED:
1
2
3
4
5
5/16”
Curved Slotted Washer
5/16” x 12mm
Hex Nut
12 pcs.
12 pcs.
6 pcs.
3 pcs.
4 pcs.
4 pcs.
4 pcs.
1 pc.
12 pcs.
56 pcs.
1 pc.
58 pcs.
8 x 19mm Short Screw
12mm Wrench
51 x 38 x 1.5mm
Small Metal Bracket
200 x 52 x 4mm
Long Metal Bracket
5/16” x 19mm
Flat Washer
5/16” x 13mm
Spring Washer
5/16” x 2-1/2” Bolt
5/16”x2-1/2”
Threaded Rod
8 x 30mm
Medium Screw
NO. ITEM DESCRIPTION
QTY.
6
7
8
9
10
11
12
4mm Allen Key
CALLUM S T ORA G E TWIN BUNK

STEP 2:
Thread the Threaded Rod (1) into the insert nuts of the Headboard/ Footboard (A) (Refer to
Detail "AA").
STEP 1:
Remove [3] drawers by pulling them out of the Storage Box (I).
Page 6 of 13
CALLUM STORAGE TWIN BUNK

STEP 3:
1-Attach the Front/ Back Guard Rails (C), and Bottom Side Rail (F),and Storage Box (I) to the Head
board/ Footboard (A) by aligning pre-installed wooden dowels and pre-drilled holes on Back Panel
with the pre-drilled holes on the Headboard/ Footboard (A).
2- Attach the Front/ Back Guard Rails (C), and Bottom Side Rail (F) to the Headboard/ Footboard (A)
with Curved Slotted Washer (2) and Nut (3) onto Threaded Rod (1),and tighten loosely by Wrench
(5) (refer to Detail "BB").
3-Attach the Storage Box (I) to the Headboard/ Footboard (A) withFlat Washer (9), Spring
Washer (10), Bolt (11), and using Allen Key (12) tighten (refer to Detail "CC").
4-Tighten all bolts at this time.
Page 7 of 13
CAL L UM S T O R A G E TWIN BU N K
NOTE: Bunk must be assembled by at leat 2 people. Set all parts in final position for assembly,
in a straight line.

STEP 5:
1. Open end of Short Side Guard Rail (E) must be positioned against Headboard/ Footboard (A),
and closed end of Short Side Guard Rail (E) must be positioned against Ladder (B).
2. Attach Long Metal Brackets (8) to the Back Guard Rail (E) using 8x19mm Short Screws (6) that
are provided.
2. Install Short Side Guard Rail (E) as indicated below and in Detail "DD".
4. Attach the Cross Bar (F) to the Headboard/ Footboard (A) by using Flat Washer (9), Lock
Washer (10), Bolt (11) with Allen Key (12) provided (refer to Detail "DD").
5. Tighten all bolts at this time.
STEP 4:
Short Side Guard Rail (E) can be attached to headboard or footboard, depending on where you
would like the Ladder (B) to be positioned (use options below).
Page 8 of 13
CALLUM STORAGE TWIN BUNK

STEP 7:
Attach Small Metal Brackets (7) to top ends of all guard rails using 8x19mm Short Screws (6) that
are provided (refer to Detail "FF").
STEP 6:
Attach the Long Side Guard Rail (D) to the Headboard/ Footboard (A) by using Long Metal Brackets
(8) and Short Screws (6) that are provided (refer to Detail "EE").
Page 9 of 13
CALLUM STORAGE TWIN BUNK

STEP 8:
1. Lay the Stretcher Bars (G) inbetween the Front/ Back Guard Side Rails (C), thentighten using
Medium Screws (4) and Philips Head screwdriver (refer to Detail "GG").
2. Lay the Slat Roll (J) inbetween the Bottom Side Rail (F) and Storage Box (I), use Medium Screws
(4) to fasten four end slats (two on each end) to side rails with a screwdriver (refer to Detail "HH").
Page10 of 13
CALLUM S T ORA G E T WINBUNK
NOTE: If you need to move the unit, do not drag it. 2 or more people are needed to safely move the unit.

STEP 9:
Page 11 of 13
CAL L UM S T O R A GE TWIN BU N K
Position the Ladder (B) inthe opening between the Front/ Back Guard Rail (C) and the Short Side
Guard Rail (E). Hook the Ladder (B) over the top and bottom side rails and tighten withShort
Screws (6) using Phillips head screwdriver (refer to Detail "II", "JJ").

STEP 10:
Page12 of 13
CALLUM S T ORA G E T WINBUNK
1. Lay the Top Platform Panels (H) on top of the Stretcher Bars (G) and attach using Qty.40 Medium
Screws (4) withPhillips head screwdriver (refer to Detail "KK").
2. Place the drawers back into the Storage Box (I).

STEP 11: INSTALL BEDDING
BEDDING SPECIFICATIONS FOR TOP BUNK:
The following size mattress and Foundation are specified for use with this Bunk bed:
MATTRESS DIMENSION SPECIFICATIONS FOR TOP BUNK
Twin - over - twin Bunk: (74" - 75") long x (37 1/2" - 38 1/2") wide x 9" thick
PLATFORM :
-Twin - over - twin bunk: Upper bed consists of 2 pcs platform 37 3/4" long x 38 3/4" wide x 3/4" thick
& bottom bed consists of 14 pcs slats 38 3/4" long x 2 1/2" wide x 3/4" thick.
**Note: MATTRESS THICKNESS MUST NOT EXCEED MAX 9" FOR TOP BUNK.
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling or
entrapment. THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO !
Page 13 of 13
CALLUM STORAGE TWIN BUNK