RH BEZIER SHELTER BED User manual

Thank you for choosing this quality product. Be sure to check all packaging materials carefully for small parts that may have
become loose during shipment and place all parts on a non-abrasive surface.
These bed parts can be cumbersome and heavy; the assistance of two or more people is recommended in order
to prevent personal injury and ensure the bed parts are not damaged during the assembly process.
PARTS INCLUDED
A [1] HEADBOARD
B [1] FOOTBOARD
C [2] SIDE RAILS
D [1] SUPPORT SLAT
E [3] LEG
F [2] FLAT FORM PANEL
NO. ITEM DESCRIPTION QTY.
3
8 pcs.
Threaded rod
1
2
4
5
Hex nut
Lock washer
Curved slotted washer
Wrench
6Screws
8 pcs.
8 pcs.
8 pcs.
1 pcs.
2 pcs.
A
F
BC
E
D
STEP 2:
Repeat the above procedure with the other side
rail (C) to attach it to the headboard (A).
Repeat to connect the side rails (C) to the
footboard (B).
FIGURE 01
Page 1 of 2
10/1/18
BEZIER SHELTER BED INSTRUCTIONS
STEP 1:
Place the headboard (A) upright in the location
you wish the bed to be in when fully assembled.
The headboard (A) fast hardware should be
facing the inside, toward the mattress. Secure
the threaded rods (1) to the fixed nuts in the
headboard (A) by turning manually. Raise the
side rail (C) up and align the threaded rods (1)
with the bore holes on the end of the side rails
(C). Put the side rails (C) up against the
headboard (A) so the threaded rods (1) go
through the bore holes. Insert the curved slotted
washers (4), lock washers (3) and hex nuts (2)
onto the threaded rods (1). Tighten with the Allen
wrench (5) provided. Refer to FIGURE 01.

Thank you for choosing this quality product. Be sure to check all packaging materials carefully for small parts that may
have become loose during shipment and place all parts on a non-abrasive surface.
These bed parts can be cumbersome and heavy to some people, therefore the assistance of two or more
people is recommended in order to prevent personal injury and ensure the bed parts are not damaged during the
assembly process.
COMPONENTS
A [1] HEADBOARD
B [1] FOOTBOARD
C [2] SIDE RAILS
D SUPPORT SLATS
E [3] LEG
F [2] FLAT FORM PANEL
NO. ITEM DESCRIPTION QTY.
3
8 PCS
Threaded Rod1
2
4
5
Hex Nut
Lock Washer
Curved Slotted Washer
Wrench
6Screws
8 PCS
8 PCS
8 PCS
1 PCS
2 PCS
A
F
BC
E
D
STEP 1:
Place the Headboard (A) upright in the position
you wish the bed to be in when fully assembled.
The Headboard (A) fast hardware should be
facing the inside, toward the mattress. Secure
the Threaded Rods (1) to the fixed nuts in the
Headboard (A) by simply turning manually. Raise
the Side Rail (C) up and place the Threaded
Rods (1) to align with the bore holes on the end
of the Side Rails (C). Put the Side Rails (C) up
against the Headboard (A) so the Threaded Rods
(1) go through the bore holes. Insert Curved
Washers (4) Lock Washers (3) and Hex Nuts (2)
onto Threaded Rods (1) and tighten with Allen
Wrench (5) provided, as shown in FIGURE 01
STEP 2:
Repeat the above procedure with the other Side
Rail (C) to attach it to the Headboard (A) and
then repeat to connect Side Rails (C) to the
Footboard (B).
FIGURE 01
STEP 3:
On the inside face of both the headboard
(A) and the footboard (B) are pre-installed
cleats with cavities for the support slats (D).
Install the legs (E) on the support slats (D), as
shown in FIGURE 02-A. Secure the support
slats (D) on the cavities of the headboard (A)
and footboard (B) with the screws (6) provided, as
illustrated in FIGURE 02-B.
FIGURE 02
FIGURE 02-A FIGURE 02-B
FIGURE 03
STEP 4:
Set the flat form panel (F) in the middle, as
shown in FIGURE 03. Assembly is
complete.
Page 1 of 2
Bezier Shelter Bed - Page 2 of 2
10/1/18