RH 18TH C. SPINDLE TURNED QUEEN BED User manual

3
Threaded Rod
4
Curved Washer
5
Hex Nut
Lock Washer
Wrench
NO. ITEM DESCRIPTION QTY.
2
18 pcs.
8 pcs.
1 pc.
PARTS INCLUDED
A
B
C
D
E
F1
F2
G
H
I
J
[1]
[2]
[1]
[7]
[1]
[1]
[1]
[4]
[4]
[4]
[4]
HEADBOARD
SIDE RAILS
FOOTBOARD
BED SLATS
SLAT SUPPORT
SHORT SUPPORT LEG
LONG SUPPORT LEG
FEET
SHORT POSTS
LONG POSTS
FINIALS
8 pcs.
8 pcs.
ASSEMBLY INSTRUCTIONS
1. Gently lay the headboard (A) and footboard (C) on a flat and
non-abrasive surface.
2. Attach the feet (G) to bottom of the headboard (A) and footboard (C). Refer
to FIGURE 1.
3. Place the headboard (A) upright in the location you wish the bed to be in
when fully assembled. Secure the threaded rod (1) to the fixed nut in the
headboard by simply turning it manually. Raise the side rail (B) and place the
rod (1) to align with the bore holes on the end of the side rails (B). Put the
side rail (B) up against the headboard (A) so the threaded rods go through
the bore holes. Insert curved washer (2) and lock washer (3), place hex nuts
(4) on threaded rod (1) and tighten hex nuts (4) with wrench (5). See FIGURE
2.
4. Repeat the above procedure with the other side rail (B) to attach it to the
headboard (A), and then repeat to connect both side rails (B) to the
footboard (C).
C
FIGURE 1
G
FIGURE 2
1
2
3
4
5
B
B
6Allen Wrench 1 pc.
Page 1 of 4
18TH C. SPINDLE TURNED QUEEN BED ASSEMBLY INSTRUCTIONS
10/1/18
HARDWARE INCLUDED

5. Attach the short support leg (F1) to the slat support (E) by turning it manually. See FIGURE 3.
6. There are pre-installed metal brackets on inside of both headboard (A) and footboard (C) for the slat support (E). Set the slat support (E) on the metal
brackets as shown in FIGURE 4. Check support rail leveling and adjust the leveler at the bottom of the support leg (F) if necessary. See FIGURE 5.
7. Set the bed slats (D) into the cavities on the slat holder rails of the side rails (B), as shown in FIGURE 6.
E
F1
FIGURE 3
Fig. 4
Fig. 3
Fig. 5
Leveler
FIGURE 4
FIGURE 5
E
D
D
FIGURE 6
18th C. Spindle Turned - Page 2 of 4
10/1/18
18TH C. SPINDLE TURNED QUEEN BED ASSEMBLY INSTRUCTIONS

NOTE: Before starting this step, securely remove all slats, support slat and short support leg from the assembled bed.
For the default setting, the slat support rail will be attached to the lower setting on the side rail. If you want to attach the slat support rail to the higher setting,
please unscrew all bolts and move the slat support rail to the top setting on side rail. Re-install the bolts and slat support rail to secure to the side rail. See
FIGURE 7.
For the default setting, the metal bracket will be attached to the lower setting at front of headboard and back of footboard. If you want to attach the metal bracket
to the higher setting, please unscrew and move the metal bracket to the top setting on headboard and footboard. Re-install the screws and metal bracket to
secure to the headboard and footboard. See FIGURE 8.
Remove the short support leg (F1) and change it to long support leg (F2). See FIGURE 9.
E
F2
FIGURE 9
18th C. Spindle Turned - Page 3 of 4
10/1/18
18TH C. SPINDLE TURNED QUEEN BED ASSEMBLY INSTRUCTIONS

8. Install all the posts (H / I) and finials (J) on the headboard (A) and footboard as shown
in FIGURE 10.
NOTE: You can remove segments of the posts (H / I) to shorten.
9. Assembly is complete.
CARE INSTRUCTIONS
1. Dust often using a clean, soft, dry and lint-free cloth.
2. Blot spills immediately and wipe with a clean, damp, cloth.
3. We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
IMPORTANT SAFETY INSTRUCTIONS
1. Please read all instructions carefully before assembling.
2. For your safety, assembly by two or more adults is strongly recommended.
3. Keep these instructions for future use.
4. Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural integrity of the item.
J
I
H
FIGURE 10
18th C. Spindle Turned - Page 4 of 4
10/1/18
18TH C. SPINDLE TURNED QUEEN BED ASSEMBLY INSTRUCTIONS