Rice Lake 880 Performance Series User manual

880 Performance™ Series
Analog Output Option Card Installation
The Analog Output Option Card provides a single analog output port for an 880 indicator when installed. The Analog Output
Option Card attaches to the 880 CPU board and is configured in the Analog Output Menu (ALGOUT) within the Setup Menu of
the 880. Configuration and calibration instructions for analog output are provided in the 880 Technical Manual (158387).
The indicator automatically recognizes all installed option cards when the unit is powered on. No hardware-specific
configuration is required to identify an installed option card to the system.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
Always disconnect power before opening an enclosure or controller assembly. Option card is not hot swappable.
Procedures requiring work inside the indicator must be performed by qualified service personnel only.
A grounding wrist strap must be worn to protect components from electrostatic discharge (ESD) when working
inside an enclosure or controller assembly.
Parts Breakdown
The Analog Output Option Card kit (179156) contains the necessary items used for installation of the option card.
Figure 1. Analog Output Option Card Parts Breakdown
Item No. Part No. Description Qty. Item No. Part No. Description Qty.
1 181658 Faceplate, Analog Output 1 – 53075 Clamp, Ground Cable Shield, 0.078'' 1
2 164704 Board Assembly, Analog Output 1 – 67550 Clamp, Ground Cable Shield, 0.125'' 1
3 14822 Screw, Machine 4-40 x 1/4 4 – 15139 Washer, No. 10 Lock 1
4 157173 Label, Analog Option 880 1 – 14621 Nut, Keps 6-32 Hex 1
–153878 Connector, 4 Position Screw Terminal 1 – 200273 Addendum, Analog Output Card 1
Table 1. Analog Output Option Card Parts List
WARNING
CAUTION
3
2
1
4
3
PN 200273 Rev BJuly 20, 2021

880 Analog Output Option Card Installation
2 Visit our website www.RiceLake.com
Panel Mount Installation
1. Disconnect power to the indicator.
2. Unhook the controller assembly from the front panel DIN rail by inserting a flat blade screwdriver into the bottom tab
and sliding the mounting plate down (Figure 2). Due to the angle of the hook portion of the DIN bracket, it may be a
little tight as it is disconnected.
Carefully separate the controller assembly from the front panel. The display cable harness still connects the
front panel to the controller assembly.
3. Disconnect the display cable harness from the controller assembly.
Figure 2. Front Panel and Backplate Removal
4. Remove the four screws securing the controller assembly backplate to the enclosure and carefully pull the backplate
straight out from the enclosure.
Removing the backplate from the enclosure voids the Legal for Trade status if enclosure is sealed.
5. Remove the two screws securing the power supply board to the backplate and carefully lay the power supply down.
Figure 3. Power Supply Board and Faceplate Cover Removal
6. Remove the two screws securing the option opening faceplate cover to the CPU board standoffs.
7. Carefully align the J5 connector on the bottom of the option card board with the J8 connector on the 880 CPU board.
IMPORTANT
Display Cable
Harness
Screwdriver
Opening Tab Backplate
IMPORTANT
Power Supply
Board
Power Supply
Board
Option Opening
Faceplate Cover
J8 Connector

880 Analog Output Option Card Installation
© Rice Lake Weighing Systems ● All Rights Reserved 3
8. Press down on the option card board until it is seated on the 880 CPU board connector.
Figure 4. Option Card Board and Faceplate Installation
9. Use three provided option kit screws to secure the option card board to the threaded standoffs on the 880 CPU board.
10. Use the remaining screw provided in the option card kit to secure the option card faceplate to the threaded mounting
block on the option card board within the option opening of the 880 panel mount backplate.
11. Reconnect the power supply board to the backplate with the two previously removed screws.
12. Slide backplate with boards into the controller assembly enclosure, ensuring that each board is seated correctly in the
grooves of the enclosure.
Before securing the backplate, verify the display connector aligns properly with the front cutout. If not aligned,
remove the backplate with boards and re-insert so the display connector aligns with the front cutout.
Figure 5. Backplate with Boards Reassembly
13. Secure backplate to controller assembly enclosure with the four previously removed corner screws.
14. Reconnect the display cable harness and then reconnect the controller assembly to the front panel DIN rail.
15. Connect necessary cable(s). See Connection Pin Assignments on page 5 for additional information.
16. Shield ground the cable(s) using a cable clamp, washer and nut provided in the option card kit and a grounding stud
on the controller assembly backplate.
See the 880 technical manual (158387) for additional information on shield grounding.
17. Reconnect power to the indicator.
18. If needed, see the 880 technical manual (158387) for additional information on Analog Output configuration.
J8 Connector
Option Card
Board
Option Card
Faceplate
Note
Option Card
Groove
Note

880 Analog Output Option Card Installation
4 Visit our website www.RiceLake.com
LED Status Indicators
Figure 6. Analog Output Option Card Faceplate
Universal Mount Installation
1. Disconnect power to the indicator.
2. Remove the backplate of the enclosure as instructed in the 880 technical manual (158387) to access the CPU board.
3. Carefully align the J5 connector on the bottom of the option card board with the J8 connector on the 880 CPU board.
Figure 7. Option Card Board Installation
4. Press down on the option card board until it is seated on the 880 CPU board connector.
5. Use three provided option kit screws to secure the option card board to the threaded standoffs on the 880 CPU board.
The provided faceplate is not needed when installing the option card inside of the 880 universal enclosure.
6. Route and connect necessary cable(s). See Connection Pin Assignments for additional information.
7. Shield ground the cable(s) using a cable clamp, washer and nut provided in the option card kit and a grounding stud
on the enclosure.
See the 880 technical manual (158387) for additional information on shield grounding.
8. Secure the backplate and then reconnect power to the indicator.
9. If needed, see the 880 technical manual (158387) for additional information on Analog Output configuration.
LED Status
1 LED Card Status
2 Green LED – Channel is good when lit
3 Red LED – Channel is faulty when lit
Table 2. LED Status Descriptions
CHANNEL 1
V
-
V
+
I
-
I+
LED
1
LED
2
LED
3
Threaded
Standoffs
J8
Connector
Note
Note

880 Analog Output Option Card Installation
© Rice Lake Weighing Systems ● All Rights Reserved 5
Connection Pin Assignments
The indicator automatically recognizes installed option cards when the unit is powered on. No hardware-specific
configuration is required to identify the newly-installed card to the system.
Figure 8. Analog Output Option Card Board
Specifications
Resolution: 16-bit, monotonicity over temperature
Linearity: ±0.03% of full scale input
Current Output: 0–20 mA or 4–20 mA (20% offset)
Maximum Load Resistance: 840 Ω
Voltage Output: 0–10 VDC
Minimum Load Resistance: 1.1 KΩ
Input Protection: Short circuit protection, 300 W transient voltage suppression
Protection for ESD, EFT (electrical fast transients), tertiary lightning, and system-generated transients
per IEC 60001-4-2, 60001-4-4, and 60001-4-5; European Standards EN50082 and EN61000-4
J1 Pin Signal
1 I+ (Current Out)
2 I – (Current Out)
3 V+ (Voltage Out)
4 V – (Voltage Out)
Table 3. Pin Assignments
Note
J4
J3
LED2
LED1
LED3
LED8
J1
CHANNEL 1
V -
V +
I
-
I+
J6
S1

230 W. Coleman St. • Rice Lake, WI 54868 • USA
U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe [phone]
Rice Lake Weighing Systems is an ISO 9001 registered company.
© Rice Lake Weighing Systems Specifications subject to change without notice.
www.ricelake.com
PN 200273 Rev BJuly 20, 2021