Rice Lake MSI-7300 User manual

MSI-7300
Dyna-Link 2 Tension Dynamometer
Technical Manual
PN 152160 Rev E
May 24, 2021

An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Contents
© Rice Lake Weighing Systems ● All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4.1 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4.2 Annunciators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.5 Available Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.6 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Zero. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3.1 Tare and Display the Net Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3.2 Clear the Tare and Revert to GROSS Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Battery Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.0 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.1 Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.2 Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.3 Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.4 NET/GROSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2.5 Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2.6 Peak Hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2.7 2-Units/ 5-Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2.8 Hi-Res . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2.9 Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3 Auto Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.4 Setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.5 Total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7 Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8 Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1 Standard Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 Initial Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2.1 Guidelines for Capacity and Resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3 C-Cal Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.4 Calibration Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.4.1 Standard Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.4.2 Auto Zero Maintenance (AZM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.4.3 Zero on Power-up (0.P-UP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

MSI-7300 Dyna-Link 2
ii Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
6.0 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.1 Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1.1 Standard Print Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1.2 Printer Output Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2 RF Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.3 Comm Port Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.4 802.15.4 RF Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.4.1 RF Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.5 Setup Multiple Sensor Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.6 Radio Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.6.1 802.15.4 (XBee 3 and XBee 3-PRO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.6.2 802.15.4 (XBee 2SC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.6.3 Wi-Fi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.6.4 Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.6.5 FHSS (Frequency Hopper Spread Spectrum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7.0 Optional Rugged Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.1 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.1.1 Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.1.2 Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.1.3 Programmable Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.2 Conflict and Jamming Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.3 FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
8.0 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8.1.1 Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.2 Service Counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8.3 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.4 Standard Capacities and Resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.5 Firmware Update Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
9.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
The MSI-7300 Dyna-Link 2 is a reliable, accurate, easy to operate, multipurpose tension dynamometer. Designed with safety
factors exceeding the industry standard, the unit is ideal for situations in which headroom is at a minimum. The unit is fully
sealed for outdoor use in any weather.
A remote display option is available to further enhance the safety and usability of the Dyna-Link 2. The optional RF remote
display allows tension monitoring from a distance and adds the ability to print and store data.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
1.1 Features
• Designed to meet or exceed all U.S. and International safety and environmental standards.
• Greater than 150 hours operation with two standard Alkaline C cells. Greater than 300 hours with two standard Alkaline
D Cells (25000 lb/12500 kg capacities and above). Also works with off the shelf NiMH rechargeable cell batteries.
• Automatic power off conserves battery life by turning the unit off when sensing no activity for a set time.
• Rugged construction throughout. IP65/NEMA Type 4 for outdoor use.
• Designed for use with U.S. made Crosby shackles (optional).
• Shackle holes reinforced with steel sleeves (25000 lb/12500 kg capacities and above) to reduce wear.
• Shackle stops ensure ease of mounting. The stops prevent the shackles from falling to the side of the unit and are held
in position for easy rigging.
• ScaleCore technology provides precision, high resolution (2500 division standard, up to 10,000 possible) 24 bit A/D
conversion coupled with an advanced RISC micro-controller. ScaleCore technology provides quick and easy firmware
updates, setup, calibration and backup.
• Five, 1.22'' (31 mm) LCD digits for clear tension readings. Six digits, 1'' (26 mm) on units 100,000 lb and over.
• Easy to maintain. Full digital calibration ensures reliable, repeatable measurements. Can be calibrated without test
weights using C-Cal technology.
• Selectable kg/lb/tons (U.S. Short)/metric tons/kilo-newtons.
• Automatic or manual weight totalization for loading operations.
• Easily customized for special applications.
• Hi speed peak mode for stress and drop test analysis.
• Two setpoints can be set for any in-range tension/weight value for operator alerts or process control.
• Two service counters ensure load train safety by warning the user to perform safety checks when the lift count gets high
or the Dyna-Link 2 has been overloaded repeatedly. Counter 1 (Lift Count) records the number of lifts above 25% of
capacity. Counter 2 (Overload Count) records the number of times the unit was overloaded.
1.2 FCC Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Canada
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la Class A prescites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des
Communications du Canada.

MSI-7300 Dyna-Link 2
2 Visit our website www.RiceLake.com
1.3 Safety
Safety Signal Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not stand on, under or near the load being lifted as it is a potential falling hazard. Keep a safe distance.
Do not use for purposes other then weight taking or dynamic load monitoring.
Do not use any load bearing component that is worn beyond 5% of the original dimension.
Do not use the dynamometer if any of the components of the load train are cracked, deformed, or show signs of fatigue.
Do not exceed the rated load limit of the dynamometer, rigging elements or the lifting structure.
Do not allow multi-point contact with the shackles of the dynamometer unit.
Do not allow high torque on the dynamometer unless it is specifically designed for high torque.
Do not make alterations or modifications to the dynamometer or the shackles.
Do not use improperly rated or sized shackles. Use only Rice Lake recommended shackles.
Do not remove or obscure warning labels. Replace labels when worn. Contact MSI for replacement labels.
For guidelines on the safe rigging and loading of overhead scales and dynamometers, read the Crane Scale Safety and Periodic
Maintenance Manual.
Keep hands, feet and loose clothing away from moving parts.
There are no user serviceable parts within the Dyna-Link 2. Repairs must be performed by qualified service personnel only.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 3
1.4 Display
Figure 1-1. Dyna-Link 2 Front Panel
1.4.1 Keys
1.4.2 Annunciators
Item No. Key Description
15 Power – Turns the Dyna-Link 2 on and off. In setup mode, it returns the unit to tension display without saving settings
16 Zero – Used to zero out residual tension on the link; In setup mode, it saves settings and drops back one menu level
17 F1 – Programmable to user functions (Section 4.2 on page 9)
18 F2 – Programmable to user functions (Section 4.2 on page 9)
Table 1-1. Key Descriptions
Item No. Description
1 F1 and F2 LEDs – Indicates the function of the associated F-key is active;
Example: In Peak Hold mode the associated LED will blink whenever a new peak reading is captured.
2 Setpoints – User programmable setpoints for early overload warnings
3 Center-of-Zero – Indicates the tension is within 1/4 d of zero
4 Standstill – Indicates the tension force has settled within the motion window (usually ±1d)
5 Low Battery – Displays when approximately 10% of battery life remains and blinks when automatic shutdown is imminent
6 Peak – Indicates Peak Hold mode
7 Total – Displays the total accumulated weight for less than five seconds
8 Net – Indicates the unit is in the net tension mode (Gross - Tare = Net)
9 Metric Ton – In conjunction with the ton annunciator, indicates the unit is displaying metric tons;
When used with the total display, it is used for X1000 to allow accumulation of weight beyond the five digit display capacity;
It is also used with the service counters when the number of lifts exceeds five digits
10 Ton – Illuminated alone, indicates the unit is displaying in U.S. short tons (1 ton = 2000 lb);
When illuminated along with the metric ton, the unit is displaying in metric tons (1 metric ton = 1000 kg)
11 Kilogram– Indicates the tension display is in kilograms
12 Kilonewton – Indicates the tension display is in kilonewtons
13 Pound Key – Indicates the tension display is in pounds
14 Five digit 1.22'' (31mm), sunlight visible, LCD Tension Display;
Units with maximum capacity of 100,000 lb and up come with a six digit 1'' (26 mm) display
Table 1-2. Annunciator Descriptions
BT
1
3 4 5 6 7 8
2
9 10
1
11 12 13
14
15 16 17 18

MSI-7300 Dyna-Link 2
4 Visit our website www.RiceLake.com
1.5 Available Configurations
Table 1-3. Available Configurations
Part No. Description
Dyna-Link 2 Digital Tension Dynamometer
139162 MSI-7300 1000 Lb Final Assembly
139163 MSI-7300 2500 Lb Final Assembly
139164 MSI-7300 5000 Lb Final Assembly
139165 MSI-7300 10000 Lb Final Assembly
139166 MSI-7300 25000 Lb Final Assembly
139167 MSI-7300 50000 Lb Final Assembly
139168 MSI-7300 100,000 Lb Final Assembly
Dyna-Link 2 Digital Tension Dynamometer With Integrated RF Module For Connectivity To MSI-8000 RF Remote Display
139441 MSI-7300RF 1000 Lb Final Assembly
139442 MSI-7300RF 2500 Lb Final Assembly
139443 MSI-7300RF 5000 Lb Final Assembly
139444 MSI-7300RF 10000 Lb Final Assembly
139445 MSI-7300RF 25000 Lb Final Assembly
139446 MSI-7300RF 50000 Lb Final Assembly
139447 MSI-7300RF 100000 Lb Final Assembly
152794 MSI-7300RF 120,000 Lb Final Assembly
152795 MSI-7300RF 180,000 Lb Final Assembly
152796 MSI-7300RF 260,000 Lb Final Assembly
152797 MSI-7300RF 380,000 Lb Final Assembly
152798 MSI-7300RF 550,000 Lb Final Assembly
Dyna-Link 2 Digital Tension Dynamometer With Integrated Bluetooth RF
176806 MSI-7300 1,000lb F/A with Bluetooth RF
176807 MSI-7300 2,500lb F/A with Bluetooth RF
176808 MSI-7300 5,000lb F/A with Bluetooth RF
176809 MSI-7300 10,000lb F/A with Bluetooth RF
176810 MSI-7300 25,000lb F/A with Bluetooth RF
176811 MSI-7300 50,000lb F/A with Bluetooth RF
176812 MSI-7300 100,000lb F/A with Bluetooth RF
176822 MSI-7300 120,000lb F/A with Bluetooth RF
176823 MSI-7300 180,000lb F/A with Bluetooth RF
176824 MSI-7300 260,000lb F/A with Bluetooth RF
176825 MSI-7300 380,000lb F/A with Bluetooth RF
176826 MSI-7300 550,000lb F/A with Bluetooth RF
Dyna-Link 2 Digital Tension Dynamometer With Integrated Wi-Fi RF
176813 MSI-7300 1,000lb F/A with Wi-Fi RF
176814 MSI-7300 2,500lb F/A with Wi-Fi RF
176815 MSI-7300 5,000lb F/A with Wi-Fi RF
176816 MSI-7300 10,000lb F/A with Wi-Fi RF
176817 MSI-7300 25,000lb F/A with Wi-Fi RF
176818 MSI-7300 50,000lb F/A with Wi-Fi RF
176819 MSI-7300 100,000lb F/A with Wi-Fi RF
176827 MSI-7300 120,000lb F/A with Wi-Fi RF
176828 MSI-7300 180,000lb F/A with Wi-Fi RF
176829 MSI-7300 260,000lb F/A with Wi-Fi RF
176830 MSI-7300 380,000lb F/A with Wi-Fi RF
176831 MSI-7300 550,000lb F/A with Wi-Fi RF

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 5
1.6 Options
Part No. Description
151361 Shackle 175 Ton G2140
151357 Shackle Anchor 3.25 Ton Bolt Type
151355 Shackle Anchor 6.5 Ton Bolt Type
141992 Shackle Anchor 17 Ton Bolt Type
151356 Shackle Anchor 25 Ton Bolt Type
146336 Shackle Anchor 55 Ton Bolt Type
151359 Shackle, Bolt Type 160000lb (85 Ton) G-2140
151360 Shackle, Bolt Type 220000lb (120 Ton) G-2140
151361 Shackle, Bolt Type 350000lb (175 Ton) G-2140
151358 Shackle, Bolt Type 500000lb (250 Ton) G-2140
139381 MSI-8000 Remote Display RF (Requires an MSI Crane Scale or MSI-7300 equipped with a RF Modem)
153591 Final Assembly Remote Display AC Power 8000HD
165313 MSI-7300 Carry Case with Foam for use with 1K-10K MSI-7300 and MSI-8000
145076 MSI-7300 Transport Case For Use With 25k And 50k DynaLink 2 Digital Tension Dynamometers
145073 MSI-7300 Shipping Crate For Use With 100k Dyna Link 2 Digital Tension Dynamometers
139470 Cable Assembly Heavy Duty Serial Dyna-Link 2 MSI-7300
178004 LaserLight2, 4'' (101 mm) Six-digit RF Scoreboard (requires MSI-7300 equipped with optional RF modem)
178006 LaserLight2, 6'' (152 mm) Six-digit RF Scoreboard (requires MSI-7300 equipped with optional RF modem)
150964 Cable Assembly, Serial I/O DCE D9 Sockets 8000
Table 1-4. Available Options

MSI-7300 Dyna-Link 2
6Visit our website www.RiceLake.com
2.0 Operation
This section includes the basic operation of the Dyna-Link 2.
2.1 Power
Turn on the Dyna-Link 2 by pressing . The LCD displays all segments for a display test and the software version number
will briefly display. When  displays, the unit is ready for use.
2.2 Zero
Press to remove small deviations in zero when the Dyna-Link 2 is unloaded. See Section 2.3 for zeroing (taring)
package or pallet weights.
• Zero works in GROSS or NET modes.
• Zeroing while in NET mode will zero the gross tension causing the display to show the negative tare value.
• The Dyna-Link 2 must be stable within the motion window. The unit will not zero until displays. The unit holds a
zero request for two seconds. If the motion clears in that time, the unit will zero.
• The unit will accept a zero setting over the full range of the Dyna-Link 2. Zero settings above 4% of full capacity will be
subtracted from the overall capacity.
Example: If 100 lb is zeroed on a 1000 lb Dyna-Link 2, the overall capacity will reduce to 900 lb plus the allowed
over-range amount.
The tension reading must be stable within the motion window for the zero function to work.
The backup memory stores the zero reading in the event of power failure.
2.3 Tare
2.3.1 Tare and Display the Net Tension
1. Program an F-key to tare (Section 4.2.5 on page 10).
2. Press the Tare F-key.  displays and the tension mode changes to NET Tension.
The tension reading must be stable within the motion window for the tare function to work. The backup memory stores the tare
reading in the event of a power failure.
2.3.2 Clear the Tare and Revert to GROSS Tension
Press the Tare F-key. The NET annunciator turns off. The absence of the NET annunciator is the only indication the Dyna-Link
2 is in the GROSS Tension mode.
To view GROSS tension without clearing the tare value, program the remaining F-Key to the function NET/GROSS.
• Only positive gross tension readings can be tared
• The tension/force reading must be stable and must be on
• Setting or changing the tare has no effect on the gross zero setting
• The Dyna-Link 2 stores the tare value in non-volatile memory and is restored when power is cycled
• Taring will reduce the apparent over range of the Dyna-Link 2
Example: When taring 100 pounds of rigging on a 1000 lb Dyna-Link 2, the unit will overload at a net tension of
900 lb (1000-100) plus any additional allowed overload (usually about 4% or 9d).
Note
Note

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 7
3.0 Installation
3.1 Unpacking
When unpacking the Dyna-Link 2 from the shipping container, ensure that all assembly parts are accounted for.
Check for any visible damage and immediately report any damage to Rice Lake Weighing Systems and the shipper. Retain the
original shipping container for future shipping or transporting of the unit.
3.2 Assembly
Two cotter pins and two batteries are included with the Dyna-Link 2, also required for installation are shackles and pins, they
can be supplied by the customer or they can be ordered from Rice Lake Weighing Systems (Table 1-4 on page 5).
1. Slide top shackle over load cell and insert the pin.
2. Screw the shackle nut onto the pin.
It is not necessary to tighten the nut too tight. Ensure the nut is down far enough to expose the cotter pin hole.
3. Lock the shackle pin in place with the supplied cotter pin and bend the cotter pin.
4. Repeat Step 2–Step 3 for the bottom shackle.
5. Remove the battery access port cover.
6. Insert the two batteries, positive end first, into the battery shaft.
7. Reinstall the battery access port cover.
The Dyna-Link 2 load train is unsafe for use if the shackle pins are not properly secured with cotter pins.
3.3 Battery Replacement
Disposable Batteries
The BT annunciator displays when the battery is getting low. When the BT annunciator starts to blink, the batteries are close to
being completely drained. For maximum life, use the batteries until the system shuts off.
After replacing the batteries, the battery cap should be tightened using a screwdriver to ensure a proper seal and not
just tightened by hand.
Rechargeable Batteries
When using Nickel-Metal-Hydride (NiMH) cells, it is recommended that the cells are recharged immediately after the BT
annunciator starts to blink. Do not allow the batteries to discharge completely as this may compromise the recharge life of the
battery.
NiMH Cells in C and D sizes have a lower capacity then the Alkaline C and D sizes. Rice Lake Weighing Systems recommends
having two sets of NiMH batteries, so one set can be charging while the other is in use.
NiMH D cells are often repackaged C cells. Therefore there is no increase in battery life for Dyna-Links large
enough for D cells.
The use of NiCad batteries is not recommended.
If the Dyna-Link 2 will not be used for an extended period, the batteries should be removed. A small current is used when
powered off which will discharge the batteries in about six months.
Note
WARNING
Note
IMPORTANT

MSI-7300 Dyna-Link 2
8Visit our website www.RiceLake.com
4.0 Setup
This section describes parameter settings on the Dyna-Link 2.
Use the following keys for navigating through the menus when setting up the Dyna-Link 2.
1. Press and simultaneously to enter setup menu.
2. Press to scroll through the parameters or settings.
3. Press to enter a selected parameter or to save a selection and return to previous menu.
4. Press to save a selection and return to previous menu or to the Weigh mode.
5. Press to cancel and return to Weigh mode.
4.1 Setup Menu
To enter the set up menu, press and at the same time.
Parameter Settings Description
Func1
Func2
F1 key – Configurable to listed parameters; Default is peak hold; In menu mode, functions as the enter/select key
F2 key – Configurable to listed parameters; Default is display and function test; In menu mode, functions as the scroll key
OFF The F-Key is disabled
tESt Test – Runs an LCD test (Section 4.2.2 on page 9)
TotAl Total – Accumulation of multiple weighments (Section 4.2.3 on page 9)
v-ttl View Total – Activates total weight display followed by the number of samples; With total displayed, press ZERO to clear
NetGr Net/Gross – Switches the display between Net and Gross modes (Section 4.2.4 on page 9)
tArE Tare - Zeros out a known weight (rigging, a packing container or pallet) (Section 4.2.5 on page 10)
P-HLd Peak Hold – Automatically updates the display when a higher peak weight reading is established (Section 4.2.6 on page 10)
2Unit 2 Units – Toggles the force units between pounds and kilograms (Section 4.2.7 on page 10)
5Unit 5 Units – Scrolls through all available units: lb, kg, Tons (US Short), Metric Tons and kiloNewtons (Section 4.2.7 on page 10)
HirES Hi Res – Makes the MSI-8000 RF Remote Display more sensitive to motion and movement resulting in a less stable display
Print Print – Outputs a configured text string to the RS-232 port (Section 4.2.9 on page 11)
A-OFF Off
15
30
45
60
Auto Off – Sets the amount of standstill time before the Dyna-Link 2 automatically turns off (Section 4.3 on page 11)
StPt1-8 GrEat Greater Than – Triggers when the tension exceeds the set value (Section 4.4 on page 11)
LESS Less Than – Triggers when the tension is less than the set value
OFF Off – Disables the setpoint parameter
Total Off Total Accumulation - Sets the choice for weight accumulation for a single scale;
Disabled when set to off (Section 4.5 on page 12)
ttlOn Total On – A manual choice for accumulation (Section 4.5 on page 12)
A. Load
A. LASt
H. HiGH Auto Total – Settings for automatic accumulations (Section 4.5 on page 12)
Filter Off
LO
H r1
H r2
Weight Filter – Allows the scale to adjust to situations where there may be movement (Section 4.6 on page 13)
Unit lb
kg
Ton
MTon
kN
Weight Units – Sets the weight units displayed (Section 4.7 on page 14)
b.LiFE Stand
Long Battery Life – Sets the options for standard or extended battery life (Section 4.8 on page 14)
Table 4-1. Setup Menu Parameters
F2
F2
F1
F2

Setup
© Rice Lake Weighing Systems ● All Rights Reserved 9
4.2 Function Keys
There are two function keys, and on the front panel of the Dyna-Link 2. These keys can be programmed to
several different functions. See Table 4-1 on page 8 for available functions.
To assign the F-keys:
1. Press and simultaneously to enter parameter setup menu.  displays.
To set  press again.
2. Press to enter F-key set up.
3. Press to scroll through the settings.
4. Press to select the desired choice and return to the parameter menu.
5. Press to save.  displays briefly and the Dyna-Link 2 returns to the Weigh mode.
This procedure also assigns the and on the optional RF remote display.
4.2.1 Off
When the F-Key parameter is set to , there is no user key function assigned and the F-Key is disabled.
4.2.2 Test
Set an F-Key as test (Section 4.2 on page 9). To run a test, press the Test F-Key and the display will automatically scroll
through the following:
• Light all LCD segments and the LEDs
• followed by the version number
• followed by the battery level in volts
• followed by counting from 00000 to 99999
• followed by the c-cal value
The test can be single stepped by:
1. Press the Test F-key and then immediately press the key to stop the auto scroll.
2. Press to scroll through each step and press to view the step value.
Internal tests are also performed and if any test fails, an error code displays. See Section 8.1.1 on page 33 for a description of
all error codes. Press to stop the test at any time.
4.2.3 Total
1. Ensure the total mode has been programmed in the setup menu. If this has not been setup the F-Key assigned to
TOTAL will not work.
2. Program an F-key to Total (Section 4.2).
3. Press Total F-key to perform the total function that was set in Section 4.5 on page 12.
This feature should not be confused with the ttl.rd (Total Remote Devices) function, which will add weight from two or
more load sensors.
4.2.4 NET/GROSS
Press the NET/GROSS F-key to switch between gross and net mode. The NET/GROSS F-key only functions if a tare value has
been established. The operator can switch back to gross from net without clearing the tare value. Only clearing the tare, or
setting a new tare, will change the tare value held in memory.
F1
F2
F2
F2
F1
F2
F1
Note
F1
F2
F2
F2
F1
Note

MSI-7300 Dyna-Link 2
10 Visit our website www.RiceLake.com
4.2.5 Tare
Press the Tare F-key to tare out a known force, only positive and negative deviations from the tared force display.
In force measurement applications, tare is useful as a way to display differential force. It also increases accuracy as any initial
error is removed leaving only slope error.
In scale applications, tare is typically used to zero out a known weight such as rigging, a packing container or pallet.
Once zeroed, the load displays in NET tension/weight. To use tare, set an F-key to the TARE function.
• A tare value is entered by pressing the Tare F-key.
• The tare function in the Dyna-Link 2 is defined as a tare-in/tare-out operation.
• The first press of the Tare F-key stores the current tension/weight as a tare value. The Dyna-Link 2 subtracts the tare
value from the gross tension and changes the display to NET mode.
• The next press of the Tare F-key will clear the tare value and revert the display to GROSS mode.
• The optional RF remote display has a TARE key permanently available.
4.2.6 Peak Hold
The Peak Hold function uses a high speed mode of the A/D converter allowing it to capture transient tensions at a far higher
rate than typical dynamometers.
• Peak hold is cleared and enabled with the PeakHold F-key.
• When a new peak is detected, the F-key LED will flash three times.
• The accuracy of the system in Peak Hold mode is slightly reduced to 0.2% of capacity ± 5d
• The filter setting is turned off while in Peak Hold mode to ensure the fastest acquisition rate
Example: The Peak Hold function is useful in materials and fall tests. Common tests include Overall Breaking
Strain (OB€), Breaking Force, and Cycled Breaking Strain.
Capture Peak Force
1. Program an F-key to PeakHold (Section 4.2 on page 9).
2. Prepare the test stand and test a sample.
3. Press to zero out any residual strain on the link.
4. Press the PeakHold F-key. The Pk annunciator displays.
A small jump in the reading may occur depending on the stability of the test stand.
5. Apply the test force. The PeakHold F-key LED will blink tree times for each peak it detects.
6. Remove the test force and record the peak value.
7. Press the PeakHold F-key to clear the peak value.
8. To run a new test, confirm Pk is not displayed. Repeat Step 1–Step 6.
4.2.7 2-Units/ 5-Units
Program an F-key to either 2-UNIT or 5-UNIT (Section 4.2 on page 9).
Press the 2-UNIT F-key to switch the force units between lb and kg.
Press the 5-UNIT F-key to scroll through all available units: lb, kg, tons (U.S. short), metric tons, and kilonewtons.
4.2.8 Hi-Res
Program an F-key to Hi-Res (Section 4.2 on page 9).
Press the HiRes F-key to display the high resolution mode. The display will stay in high resolution mode until the HiRes F-key is
pressed again, or the power is cycled. While in the hi-res mode, the appropriate HiRes F-key LED will blink continuously at a
slow rate.
Hi-res mode does not increase the accuracy, but allows for smaller weight increments to be displayed.
Use Tare or to zero out any initial error. Hi-Res mode will make the Dyna-Link 2 more sensitive to motion and
movement resulting in a less stable display. When Hi-Res is on, the filter is automatically set to the Hi-1 setting (if Hi-2 is already
set, then the filter is not changed). This will have a small effect on settling time. When Hi-Res is turned off, the filter setting
resets to the previous filter setting.
Note

Setup
© Rice Lake Weighing Systems ● All Rights Reserved 11
4.2.9 Print
Program an F-key to Print (Section 4.2 on page 9).
Press the Print F-key to output a configured text string to the RS-232 port on the base of the unit.
If a Print F-key is programmed and the print setup is configured as continuous, then the Print F-key is used for Start Print/Stop
Print. See Section 6.3 on page 25 for more details on data output.
The print function is always available on the optional RF remote display, so it is not necessary to program a Print F-key if print
outputs will be triggered from the remote.
If the RF remote display option is installed, the Dyna-Link 2 built in comm port is used only for hard-wire connections to the RF
remote display or firmware updates.
4.3 Auto Off
The Auto Off feature prolongs the life of the battery by turning the power off when the Dyna-Link 2 is not in use. Any key press
or detected tension in motion exceeding 10d, resets the time limit and the unit remains on.
When set to , the Dyna-Link 2 will only turn off by pressing or if the battery is depleted.
Use the following steps to set the Auto Off function:
1. Press and simultaneously to enter setup menu.  displays.
2. Press to scroll to .
3. Press . The current auto off setting displays.
4. Press to scroll to the desired time.
5. Press .  displays.
6. Press to save and return to the Weigh mode.
4.4 Setpoints
The Dyna-Link 2 supports two setpoints. Common uses of set points are for warnings or process control. The unit comes
standard with two red LED outputs for a triggered set point. There is an audible output option that is triggered by setpoint 1.
Setpoints 3-8 are only for use with remote displays thats support eight setpoints.
Parameter Description
Off Setpoint is not set
GrEAt Greater Than – will trigger the setpoint when the tension exceeds the value
Less Less Than – will trigger the setpoint when the tension is less then the value
Selections for Greater Than and Less Than
nEtGr Net/Gross – responds to the tension on the display, net or gross weight
GroSS Gross – responds to gross tension regardless of the display mode
totAl Total – responds to the totaled weight
t-cnt Total Count – responds to the total count (number of samples)
LFcnt Lift Counter – counts the total number of lifts where the weight exceeded capacity by more than 25%
Table 4-2. Setpoint Parameters
F2
F2
F1
F2
F1
Note

MSI-7300 Dyna-Link 2
12 Visit our website www.RiceLake.com
To setup a setpoint:
1. Press and simultaneously to enter setup menu.  displays.
2. Press to scroll to .
3. Press . The current setting displays.
4. Press to scroll to the desired setpoint mode (Table 4-2).
5. Press to enter the Setpoint mode.
6. Press to scroll to the type of tension or weight value the setpoint should be assigned.
7. Press to enter the tension or weight value.
8. Enter the number by:
• Pressing to move the cursor position and change the number
• With the desired number displayed, press to save the number
• Press to move the cursor to the next position
• To enter a decimal point, press , the decimal point will be entered after last number displayed
• To correct a number, press to go back to numbered that needs to be corrected
9. When the weight displays, press to save and return to previous menu.
10. Press to save and return to the Weigh mode.
4.5 Total
For the accumulation of multiple weighments, the Total function uses the displayed load, so gross and net readings can be
added into the same total.
There are four modes of totalizing, a manual and three auto modes.
All modes require that the weight on the scale return below 0.5% (relative to full scale) of Gross Zero or Net Zero before the
next weighment can be added. Applied weight must be ≥1% of full scale above Gross Zero or Net Zero before it can be totaled.
Manual Total
Manual Total () adds a current weight to a previously accumulated value manually. To add weight to the total it must be
greater than 1% of capacity and not yet totaled. This assures that a weight on the scale is only added to the total once.
1. Program a F-key to Total (Section 4.2 on page 9).
2. With the weight to be added on the scale, press F-Total. The acknowledge LED blinks to indicate the weight was
accepted and the TOTAL annunciator lights. Then the total weight displays for five seconds and the number of
samples displays for two seconds.
3. Repeat Step 1 and Step 2 until all weight samples have been added.
Total Mode will not function while the scale is in motion, ensure is on. If the system fails to achieve stable
readings, increase the filter setting or increase the size of the scale division (d) in the Init Cal procedure.
The F-Total functions as View Total only until the 1% threshold is exceeded to allow the addition to the total value.
F2
F2
F1
F2
F1
F2
F1
F2
F1
F2
F1
Note

Setup
© Rice Lake Weighing Systems ● All Rights Reserved 13
Auto Total
This mode has three variations which are programmed in the Setup menu.
Program an F-key to AUTO TOTAL, it functions as Auto Total On / Auto Total Off (Section 4.2 on page 9).
To set total Mode:
1. Press and simultaneously to enter setup menu.  displays.
2. Press to scroll to Total.
3. Press to enter the total mode. The current total mode displays.
4. Press to scroll through the available parameters.
5. When the desired setting displays, press .  displays
6. Press to save and return to the Weigh mode.
Reset Total Load
To reset the total load to zero, press Fx-Total again and while the total load is being displayed, quickly press .
4.6 Filter
Changing the filter settings allows the Dyna-Link 2 to adjust to situations where there is a lot of movement in the lift or the crane
structure. If the reading is not stable, it can often be improved by increasing the filter setting. Settling time will be longer as the
filter setting is increased. The Dyna-Link 2 employs algorithms that speed up large tension changes while still controlling
vibration even with higher filter settings.
To set the filter mode:
1. Press and simultaneously to enter setup menu.  displays.
2. Press to scroll to .
3. Press . The current filter mode displays.
4. Press to scroll through the available filters.
5. When the desired filter is displayed, press .  displays.
6. Press to save and return to the Weigh mode.
Setpoint Description
A.Load Auto Load – Ensures any settled load above the Rise Above threshold will be automatically totaled; The scale must fall below the Drop
Below threshold before the next total is allowed
A.Last Auto Last – Takes the last settled weight to auto total with; The total occurs only once the scale goes below the threshold; This allows the
load to be adjusted without a total occurring; Once the load is removed, the scale uses the last settled reading for total
 Auto High – Uses the highest settled reading; This is useful for loads that can’t be removed all at once
Table 4-3. Auto Load Selections
Parameter Description
Off Disables filtering function
Lo Low Filter
Hi-1 High Filter
Hi-2 Very High Filter
Table 4-4. Filter Parameters
F2
F2
F1
F2
F1
F2
F2
F1
F2
F1

MSI-7300 Dyna-Link 2
14 Visit our website www.RiceLake.com
4.7 Units
Units can be changed in two ways:
• Program an F-key to  or 
• Change the units with the setup menu using the following procedure
Change the units with the setup menu:
1. Press and simultaneously to enter setup menu.  displays.
2. Press to scroll to .
3. Press . The current unit displays above the word .
4. Press to scroll through the units.
5. When the desired unit is displayed, press .  displays.
6. Press to save and return to the Weigh mode.
To set the accessible units available by an F-key, set as 2Unit (lb/kg) or 5Unit (lb/kg/short tons/metric tons/kilonewton)
(Section 4.2 on page 9).
If the Dyna-Link 2 Calibration was originally in tons or metric tons, the 2Unit setting will switch from tons to metric
tons instead of lb/kg.
4.8 Battery Life
In Long battery life mode, the system is placed into a sleep state for several seconds at a time if there is no change in tension.
This disables the display in order to reduce power consumption and increase battery life. After several seconds, the MSI-8000
RF Remote Display will wake up to check for any changes in tension. If there is a change in tension, the unit will stay awake.
The unit will also stay awake if it is in configuration mode.
To set Total mode:
1. Press and simultaneously to enter setup menu.  displays.
2. Press to scroll to .
3. Press . The current total mode displays.
4. Press to scroll through the available parameters.
5. When the desired setting is displayed, press .  displays.
6. Press to save and return to the Weigh mode.
Units
lb Pounds
kg Kilograms
Ton Short Tons
MTons Metric Tons
kN KiloNewtons
Table 4-5. Units
F2
F2
F1
F2
F1
Note
F2
F2
F1
F2
F1

Calibration
© Rice Lake Weighing Systems ● All Rights Reserved 15
5.0 Calibration
The Dyna-Link 2 is calibrated using standard precision test weights. It is required that the weight used is at least 10% of full
capacity in order to achieve rated accuracy.
Example: Use at least a 500kg test weight to calibrate a 5000kg capacity unit.
The Dyna-Link 2 supports load cell linearization with up to four span points that can be calibrated in any order. Usually only one
cal span point is necessary and is sufficient to reach rated accuracy.
When adequate test weights are not available, the Dyna-Link 2 can be calibrated using a Constant Calibration (C-Cal).
To use C-Cal, the factory generated C-Cal number must be known.
There are three types of calibration:
• Standard calibration is used for maintenance and routine calibration (Section 5.1 on page 16).
• Initial calibration is used to setup both the capacity and resolution (d) of the Dyna-Link 2. It differs from standard
calibration only in the initial steps. Initial calibration is performed after a calibration reset which completely erases the
calibration and parameter settings.
• C-Cal can be used if C-Cal values are known, the Dyna-Link 2 can be calibrated without weights.
The calibration menu contains three items: Cal, C-Cal, and Setup. The following procedures start with entering into the Cal
menu, or for an initial calibration, resetting the Dyna-Link 2 and then going to the Cal menu.
Parameter Selections Description
 Standard and initial calibration parameter (Section 5.1 on page 16 and Section 5.2 on page 17)
 C-Cal parameter (Section 5.3 on page 19)
 See Section 5.4.1 on page 20 and Section 5.4.2 on page 21
SETUP Sub-menu

Industrial Standard Settings
Industrial
INDus
The common setting for the MSI-8000 RF Remote Display; With the Industrial standard, the unit has full range
zero, access to units switching, filters, and peak hold
Handbook 44
HB44
Sets the scale to enable only approved features per the NTEP HB-44 rules and regulations; Access is denied to
Peak Hold, and the zero range may be limited; The Filter menu is moved to the Cal Setup Menu, so filters are only
accessible through the Cal Seal
R-76
R-76
Sets the scale to enable only approved features per OIML R-76; Only kg weight units are available; The zero
range is limited to 5% (-2 +3% relative to Calibrate zero); Net/Gross function is temporary; Once Net weight is
established, pushing an F-key set for Net/Gross will cause a maximum 5 second display of the Gross weight; The
Tare must be cleared to display Gross weight constantly; Other meteorological aspects are changed to meet R-76
requirements
One Unit
1 Unit
The one unit standard is exactly the same as Industrial, except unit switching is inhibited; This is useful for Metric
only countries; Another use of the One Unit standard is to allow the scale to be calibrated in units other than lb or
kg, since conversions are eliminated
 On
OFF Auto Zero Maintenance
0.p-up On
OFF Set to On will cause the Dyna-Link 2 to 0 when it is powered on; Default is OFF
Table 5-1. Calibration Menu

MSI-7300 Dyna-Link 2
16 Visit our website www.RiceLake.com
5.1 Standard Calibration
1. Press and simultaneously to enter the calibration menu.  displays.
2. Press to start calibration.  displays.
3. Remove all weight from the scale.
Bottom fittings can be left on the link as long as they are always part of the load train.
4. Press to set zero calibration point. If zero is in range,  displays momentarily then  is displayed.
If the calibration point is not within the limits, the display will read FAIL and the procedure will need to be repeated.
5. Load the link with a test weight. For highest accuracy, a test weight of 10% or more of capacity is recommended.
6. Press , the capacity flashes on the display.
7. To use a weight different of capacity, enter the number by:
• Pressing to move the cursor position and change the number
• With the desired number displayed, press to save the number
• Press to move the cursor to the next position
• To enter a decimal point, press , the decimal point will be entered after last number displayed
• To correct a number, press to go back to numbered that needs to be corrected
8. When the weight is displayed, press to save.  displays momentarily and then  displays.
If the Cal Value is not within the limits, the display will read FAIL and the procedure will need to be repeated.
9. If more calibration points are desired (up to three) press and repeat Step 6–Step 8.
10. Press to store calibration constants. ’ will be displayed.
11. Press , the  number displays, note for future reference.
12. Press to exit calibration.  is displayed.
13. Press to return to Weigh mode.
To cancel and return to Weigh mode during calibration, press . The previous calibration will be reset.
F2
F1
Note
F1
Note
F1
F2
F1
F2
F1
Note
F2
F1
Note