Rich View 1-1/2" Headrail 1" Corded Aluminum Blind Installation guide

Aluminumblind
Lmax
Lmax Lmax
1-1/2" Headrail 1" Corded Aluminum Blind Installation and CareInstruction 1
1-1/2" Headrail 1" Corded Aluminum Blind Installation and Care Instruction
1. Identify your aluminum blind and parts (your parts may vary, depending on the custom request & size of the blind
you are purchasing.
Wand
Hidden brackets & screws Box brackets & screws
(optional)
Extension brackets
(optional)
Spacers (optional)
Optional - Add a spacer behind the
hidden bracket or the box bracket if
needed.
Hold down brackets
& screws (optional)
Center support & screws
(optional with the box brackets,
used on the larger blinds)
Cord cleat & screws
Aluminum Blind
2. Tools you may need (not included)
•Drill with bits
•Screwdriver
•Metal tape measure
•Pen
•Mark the bracket locations, making sure the brackets will not interfere with any mechanism
or other internal headrail parts. The outermost brackets should be installed about 1/4 inch
from each end of the blind. If you have more than 2 hidden brackets, install all remaining
brackets towards the center of the blind.
•Install the brackets using screws (included) and tighten them completely.
•Make sure all brackets are aligned and level with each other.
3A. Install the blind with the hidden brackets (or choose to install the blind with the box brackets, refer to step 3B~5B.)
•Install the blind with the extension brackets (optional)
oInstall the extension bracket with at least 2 screws.
oAttach the hidden brackets to the extension brackets
with the screws.
Inside Mount Outside Mount Extension bracket
4A. Install the blind
•Fit the front lip of the headrail over the hook on the front of the hidden brackets.
•Push the blind toward the back of the brackets with a "click".
5A. How to remove the blind from the hidden brackets
•Unlock the hidden brackets with a flat head screwdriver.
3B. Install the blind with the box brackets (or choose to install the blind with the hidden brackets, refer to step 3A~5A.)
• Install the box brackets at the ends of the headrail. Use 2 screws per box bracket.
• One center support is applied when the blind is wider than 48"W, or two center supports for the blind wider than 100"W.
• The spacer is optional and is installed behind the box bracket when needed.
Inside Mount
Outside Mount
Center Support Center Support

1-1/2" Headrail 1" Corded Aluminum Blind Installation and CareInstruction 2
4B. Install the blind
•Unlock the box brackets with a flat head screwdriver.
•Mount the blind in the brackets (also use the center support when blind is wider than
48"W)
•Close the door on the bracket and hear a "click".
5B. How to remove the aluminum blind from the box brackets
• Use a flat head screwdriver to open the door of the box bracket.
• Remove the blind.
Center Sport
6. Attach the tilt wand
•Attach the tilt wand onto the wand hook located on the headrail.
7. Install the cord cleat
•Use 2 included screws and install the cord cleat at your desired
height. For safety reasons, keep the cord being unreached by child
or pet.
•Always wrap the cord around the cord cleat to keep your cord tight.
8. Attach the optional hold down brackets
•Install the hold down brackets to the wall (for outside mount) or jamb
of the window frame (for inside mount), not on the sill of the window
frame.
•Tighten the screws.
9. Care and cleaning
• Wipe the blind periodically with a soft dust cloth or a dusting mitt, or vacuum with
a soft brush attachment.
• You may clean the blinds using a non-scratched sponge or dampened soft cloth
with a mild nonabrasive detergent. Never use hot water, solvents, or harsh or
abrasive cleansers to clean the blinds.
• Note: The warranty for your blinds does not cover damage caused by improper
cleaning.
To Operate Your Blind
Important: Always tilt the slats horizontally before raising or lowing the blind. This step increases the life of the
blind.
To Lower Your Blind
Move the cord to left pulling down gently until the cord lock releases. Allow the cord to slip slowly until the blind
reaches your desired level. Pull the cord to the right and then release. The blind locks automatically.
To Raise Your Blind
Pull the cord downward until the blind reaches desired height and then slightly to the right to release the cord. The
blind locks automatically.
To Tilt Your Blind
Rotate the wand to attain desired slat position.
Important Note
ALWAYS TIE THE CORD TO THE CORD CLEAT FOR SAFETY REASONS.