Richmar HydraTherm User manual

INITIAL SET-UP
• Clip shelves onto dividers, then place dividers in tank
and arrange packs as desired. See illustrations below
for recommendation on how to maximize space for
use with 12 packs.
• Find drain hose in rear of device. Ensure the valve*
is closed (turned perpendicular to the hose) before
filling the device with water.
FILLING WITH WATER
• To fill the device, first pour in 3 cups of tap water, followed
by up to 12 gallons of distilled water, stopping when the
water level has reached 2” from the top of the tank.
NOTE: Exact amount of distilled water varies depending
on quantity of packs being used.
NOTE: Distilled water helps to maintain a clean device,
but doesn’t conduct electricity. For this reason tap water
is needed for the Low Water Sensor to operate properly.
POWERING ON THE DEVICE
• Ensure power switch on back of device is in the
OFF or O position.
• Connect the included power plug into the rear of the
device, and then into the nearest available outlet.
• If using a Deluxe HydraTherm™, ensure the Heat/Drain
switch on the rear of the device is toggled to HEAT.
• Toggle the power switch to the ON or I position.
When powered on, the power switch will illuminate, and
the digital display on the front of the device will display
the current water temperature.
Front Rack
3x Universal
Clip
Clip
2x Standard 1x Standard + 1x Cervical 2x Cervical 2x Oversize
1x Oversize
*Standard valve is green/blue. Deluxe valve is gray.
Thank you for purchasing the HydraTherm™. This Quick-Start Guide will help you to get started
quickly, but does not replace the Operating Manual. Be sure to read, understand, and practice
the operating instructions, warnings, and cautions included in the manual.
QUICK-START GUIDE
HydraTherm™

LOW WATER INDICATOR
• Check Temperature Display. If enough tap water
was added, the Low Water Indicator should NOT
be illuminated at this time. If Low Water Indicator is
illuminated, add more tap water until the indicator light
turns o.
TEMPERATURE SETTING
• Do not exceed 140° F (60° C) for best therapeutic eect,
patient comfort, and HydraHeat Pack longevity.
• It can take several hours for the water to reach the Set
Temperature. The default Set Temperature is 135°F (57°C),
to change the Set Temperature refer to instructions below.
To enter Temperature Set Mode:
• Press “SET” key on control panel,
“HSP” will then be displayed.
• Press “SET” key again and the and the current
Set Temperature will display. (e.g. 135°/57°C).
• Press UP or DOWN arrows until desired temperature is
reached. (e.g. 140°F/60°C).
• Once desired temperature is displayed, press and
release the “SET” button. The new Set Temperature is
now saved.
• To exit Temperature Set Mode, press the SET and
DOWN arrow together, or the device will exit
Temperature Set Mode automatically after
1 minute of inactivity.
WARNING: The scalding temperature of water is
140° F (49° C). Never place hands into the scalding water.
Use plastic-coated tongs to retrieve hot pack if necessary.
HYDRAHEAT PACKS
• HydraHeat Packs absorb heat, not water,
and provide therapeutic heat up to 45 minutes.
• Placing a towel or pillowcase between between
HydraHeat Pack and patient is recommended.
• Terry covers are not recommended when
using HydraHeat Packs.
Have questions? Contact Richmar:
Phone: [phone]
Email: [e-mail]
HSP
135
140
Low Water Indicator illuminated Low Water Indicator not illuminated
135 135
3000.15.09.C ©2019 Compass Health Brands Corp.
Compass Health Brands Corp.
Toll Free 1.888.549.4945
6753 Engle Road
Middleburg Heights, OH 44130
richmarweb.com
Manufactured for