RIGd Supply UltraSwing Multi-Fit User manual
INSTALLATION GUIDE
UltraSwing™ Multi-Fit
Congratulations on your UltraSwing! You’re only a few steps away from hitting the trail.
RIGd Supply 1533 W Orangewood Ave, Orange, CA 92868 | [email protected] | 714-820-9444
WARNING: Never exceed the 250 lbs total weight rating of the UltraSwing. In severe off-road
application we recommend reducing the total weight to 150lbs. UltraSwing is tow rated to
10,000 lbs (1,000 lb tongue). Never exceed your vehicle's towing capacity. Subtract the weight
of the UltraSwing (70 lbs) as well as the weight of your spare tire and all other products
mounted to the UltraSwing to determine your vehicle’s available tongue weight.
Installing the RIGd UltraSwing on your vehicle
1. Grease the sides of the UltraWedge (Figure 1)
2. Install UltraSwing into hitch
3. Check to make sure the hole the inner and outer hole are symmetrically aligned (Figure 2)
4. Tighten UltraWedge using a ¾” socket and 12” socket extension (Figure 3)
5. Tighten to 85 ft/lb
Figure 1
Figure 2
2
Figure 3
WARNING: The UltraWedge is only designed to
eliminate wobbling in the receiver. Always use a
hitch pin.
NOTE: The UltraSwing was fixtured to have
several degrees of upslope towards the passenger
side. This is in order to provide maximum
departure angle and improved aesthetics when
tire or other accessories are mounted to the
carrier.
Toyota 6-bolt Wheel Plate w/
corresponding hardware
Multi-Fit Wheel Plate w/
corresponding hardware
3
Full-Size Wheel Plate w/
corresponding hardware
Setting Multi-Fit Plate Lugs
Before mounting your wheel plate to the
UltraSwing, set your top lug to the proper
height. (Figure 4)
1. Place the wheel plate on the backside
of your rim and align the three lug
holes. (Figure 5)
2. Tighten the top lug (Figure 6)
3. Continue on to mounting the wheel
plate to the UltraSwing
Figure 4
4
Figure 5
Figure 6
Installing Wheel Plate
For 32-inch or smaller tires or plan to run an
Ultraplate we recommend starting at the
lowest set of holes.
For 33-34-inch tires we recommend to use
the middle set of holes.
For 35-inch tires we recommend to use the
highest set of holes.
(See Figure 7)
When mounting your wheel-plate and be sure
the bolts and washers are mounted from the
back side..
Tighten wheel support plate bolts to 75 ft/lb
Figure 7
5
Please note that the bolts and
washers go through the backside.
(This will ensure maximum clearance
for installing an UltraPlate in the
future.)
Please note that the full size wheel
plate uses 2 washers on the top right
bolt and the thin Nylock nut
License Plate Relocation
Your UltraSwing Multi-Fit includes a license
plate relocation bracket. (See Figure 8).
Extra thick spacers can be used to space the
plate as needed. (Figure 9)
Completed install of the license plate bracket
(Figure 10)
Figure 8
6
Figure 9
Figure 10
Compression Latch Adjustment
Washers
Your latch has been pre-adjusted by RIGd.
However, if you’d like to add more
compression to the latch silver washers have
been included to fine-tune the feel of the
latch. Do not exceed 2 washers. (Figure 11)
1. Remove bumper bolt using a 5/32” or 4mm
allen wrench
2. Add or remove washer
3. Reinstall
Figure 11
7
Limited Lifetime Warranty
RIGd Supply offers a Limited Lifetime Warranty on the structure of each UltraSwing to the
original purchaser.
Exclusions
1. UltraSwings that have been abused, crashed, altered, modified, or installed on vehicles
other than those approved by RIGd Supply
2. Damages and shipping charges
3. Pivot washers, bolts, nuts, and washers. (These parts are subject to wear and are not
considered defective when worn)
4. Cost of the original installation, removal, or reinstallation
Replacement Program
RIGd Supply will make replacement parts available to the original owner at a minimal charge
in the event of a crash or other non-warranty situation for the life of the UltraSwing.
Contact
RIGd Supply
1533 W Orangewood Ave
Orange, CA 92868
714-820-9444
8
Table of contents
Other RIGd Supply Automobile Accessories manuals
Popular Automobile Accessories manuals by other brands
Spinder
Spinder XPLORER Assembly instruction and safety regulations
Westin
Westin 25-2310 instructions
Classic Accessories
Classic Accessories QuadGear Extreme instructions
Whispbar
Whispbar K835W Fitting instructions
Pittsburgh Power
Pittsburgh Power Detroit DDEC III installation instructions
Cruz
Cruz 934-624 Assembly instructions
