RIGd Supply UltraSwing Swing Out Tire Carrier User manual
INSTALLATION GUIDE
UltraSwing™Swing Out Tire Carrier
Congratulations on your UltraSwing! You’re only a few steps away from hitting the trail.
WARNING: Never exceed the 250 lbs total weight rating of the UltraSwing. In a severe off-road
application, we recommend reducing the total weight to 150lbs. UltraSwing is tow rated to
10,000 lbs (1,000 lb tongue). Never exceed your vehicle's towing capacity. Subtract the weight
of the UltraSwing (70 lbs), as well as the weight of your spare tire and all other products,
mounted to the UltraSwing to determine your vehicle’s tongue weight.
Installing the RIGd UltraSwing on your vehicle
1. Grease the sides of the UltraWedge (Figure 1) As well as the top face of the wedge to allow it
to travel while tightening
2. Install UltraSwing into the hitch
3. Check to make sure the hole the inner and outer hole is symmetrically aligned (Figure 2)
4. Tighten UltraWedge using a ¾” socket and 12” socket extension (Figure 3)
5. Tighten to 85 ft/lb
Figure 1
Figure 2
WARNING: The UltraWedge is only designed to
eliminate wobbling in the receiver. Always use a
hitch pin.
NOTE: The UltraSwing was fixtured to have
several degrees of upslope towards the passenger
side. This is in order to provide maximum
departure angle and improved aesthetics when a
tire or other accessories are mounted to the
carrier.
2
Figure 3
Installing Wheel Plate
For 32-inch or smaller tires or plan to run an
Ultraplate we recommend starting at the
lowest set of holes.
For 33-34-inch tires we recommend to use
the middle set of holes.
For 35-inch tires we recommend to use the
highest set of holes.
(See Figure 7)
When mounting your wheel-plate and be sure
the bolts and washers are mounted from the
back side.
Tighten wheel support plate bolts to 75 ft/lb
Figure 4
Toyota 6-bolt Wheel Plate w/
corresponding hardware
3
Please note the bolts and washers go on
the back side with nuts facing the tire.
(This will ensure maximum clearance if
installing an UltraPlate)
Compression Latch Adjustment
Washers
Your latch has been pre-adjusted by RIGd.
However, if you’d like to add more
compression to the latch silver washers have
been included to fine-tune the feel of the
latch. Do not exceed 2 washers. (Figure 5)
1. Remove bumper bolt using a 5/32” or 4mm
Allen wrench
2. Add or remove the washer
3. Reinstall
Figure 5
4
License Plate Relocation
Use your Toyota factory license plate bolts to
relocate your license plate to the UltraSwing.
Before installing place double-sided adhesive
pad to UltraSwing gusset. (See Figure 6).
Figure 6
Limited Lifetime Warranty
RIGd Supply offers a Limited Lifetime Warranty on the structure of each UltraSwing to the
original purchaser.
Exclusions
1. UltraSwings that have been abused, crashed, altered, modified, or installed on vehicles
other than those approved by RIGd Supply
2. Damages and shipping charges
3. Pivot washers, bolts, nuts, and washers. (These parts are subject to wear and are not
considered defective when worn)
4. Cost of the original installation, removal, or reinstallation
Replacement Program
RIGd Supply will make replacement parts available to the original owner at a minimal charge
in the event of a crash or other non-warranty situation for the life of the UltraSwing.
Contact
RIGd Supply
1533 W Orangewood Ave
Orange, CA 92868
714-820-9444
5
6
Table of contents
Other RIGd Supply Automobile Accessories manuals
