Rimage Allegro 100 User manual

Allegro 100 服务手册

目录
Section 1 – 外壳 ................................................................................................................................. 1
Section 2 – 控制面板Control Panel .............................................................................................................................. 2
Section 3 - LED板（蓝色） ........................................................................................................................................... 3
Section 4 – USB3.0 Hub ............................................................................................................................................... 3
Section 5 – 主板 ............................................................................................................................................................ 5
Section 6 – 打印机托盘 ................................................................................................................................................ 7
Section 7 – 电源电阻器Power Resistor ........................................................................................................................ 9
Section 8 – 托盘进出编码轮传感器 .......................................................................................................................... 10
Section 9 – 托盘进出编码轮 ...................................................................................................................................... 12
Section 10 – 光驱支架 ................................................................................................................................................ 13
Section 11 – 电源 ........................................................................................................................................................ 14
Section 12 – 光驱位置风扇 ........................................................................................................................................ 16
Section 13 – 光驱 ........................................................................................................................................................ 18
Section 14 – 废墨收集海绵 ........................................................................................................................................ 19
Section 15 – 维护风扇 ................................................................................................................................................ 20
Section 16 – 墨水车编码条 ......................................................................................................................................... 21
Section 17 – 墨水车马达 ............................................................................................................................................ 22
Section 18 – 墨水车托架组件 .................................................................................................................................... 24
Section 19 – 打印机托盘马达 .................................................................................................................................... 28
Section 20 –废墨区底座 ............................................................................................................................................. 30
Section 21 – 墨水车 .................................................................................................................................................... 31
Section 22 – 墨水车位置对齐传感器 ......................................................................................................................... 35
Section 23 – 墨水车排线总成 .................................................................................................................................... 38
Section 24 – 机械臂 .................................................................................................................................................... 42
Section 25 – 机械臂马达 ............................................................................................................................................. 46
Section 26 – 机械臂控制板 & 柔性电缆 .................................................................................................................... 47
Section 27 – 抓手控制板 ............................................................................................................................................. 48
Section 28 – 抓手电磁阀 ............................................................................................................................................ 51
Section 29 – 故障排除 ................................................................................................................................................ 54
Rimage® is a registered trademark of Rimage Corporation. Allegro™ is a trademark of Rimage Corporation.
© 2017, Rimage Corporation
A100SVC - 0917

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 1
Section 1 - Cover
1.1
Loosen 4 screws securing back of cover.
1.2
Remove 3 screws securing front of cover. Slide picker and carrier to middle of printer.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 2
1.3
Unplug cable from control panel on underside of cover. While lifting cover off of printer, reach
in and unplug blue LED board cable from mainboard. Remove cover.
Section 2 - Control Panel
2.1
Remove cover (see Cover). Remove 3 screws securing control panel. After replacing control
panel, press buttons to verify they click properly.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 3
Section 3 - Blue LED Board
3.1
Remove cover (see Cover). Remove 2 screws securing blue LED board. Unplug cable from end of
board.
Section 4 - USB3 Hub
4.1
Remove 2 screws securing cover plate. Remove plate.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 4
4.2
Unplug any sata cables from hub. For 2 drive units, keep track of which cable is plugged into
which port. Remove 3 screws securing hub.
4.3
When replacing hub, be sure pins properly plug into connectors on mainboard. Plug any sata
cables back in.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 5
Section 5 - Mainboard
5.1
Remove USB3 hub (see USB3 Hub). Unplug all cables and flex cables from mainboard.
5.2
Remove 4 screws securing mainboard. Lift mainboard out of unit.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 6
Feed
Carrier
Fans
Post
5.3
Remove 2 screws securing static brush to mainboard. Remove 3 standoffs. Secure static brush
and standoffs to new mainboard.
5.4
When replacing mainboard, make sure hole in corner is resting on small post before replacing 4
screws. Attach USB3 hub and plug in all cables and flex cables. Be sure to plug carrier and feed
motors into correct location. Drive and maintenance fans can be plugged into either location.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 7
Section 6 - Print Tray
6.1
Remove mainboard (see Mainboard). Remove 2 screws securing print tray guide to print tray.
Lift guide up off of tray (leave attached to belt).
6.2
Lift back end of print tray slightly and pull back against rear cover plate.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 8
6.3
Remove screw securing front tray guide. Lift guide out of base.
6.4
Pull print tray out of printer.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 9
Section 7 - Power Resistor
7.1
Cut tie wrap securing power resistor cable to power supply cable. Unplug power resistor from
mainboard.
7.2
While holding resistor mount bracket with fingers or needle-nose pliers, remove 2 screws
securing to rear cover plate.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 10
7.3
Remove 2 screws securing power resistor to resistor mount bracket. Replace resistor.
Section 8 - Encoder Wheel Sensor
8.1
Cut tie wrap securing cables. Unplug encoder wheel sensor from mainboard.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 11
8.2
Remove 2 screws securing sensor to bracket.
8.3
When replacing sensor, be sure encoder wheel is centered in slot.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 12
Section 9 - Encoder Wheel
9.1
Peel encoder wheel off of gear. Clean area with alcohol before adhering new encoder wheel.
9.2
Be sure replaced encoder wheel is centered in sensor slot. Clean encoder wheel with alcohol
after handling.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 13
Section 10 – 光驱支架
10.1
如下图将打印机朝上。 拧下下图标示的6颗螺丝。
10.2
向前倾斜光驱支架，将光驱支架的卡槽与后盖板上的卡舌对齐，然后卸下。

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 14
10.3
拔下光驱背面的所有电缆，以从打印机上卸下光驱支架。 备注两组SATA电缆和光驱的位
置。
Section 11 - Power Supply
11.1
Remove drive mount (see Drive Mount). Unplug power supply from mainboard. Cut tie wraps
securing power supply cable.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 15
11.2
Remove 5 screws securing power supply to rear cover plate.
11.3
Lift power supply out of printer. Pull drive power cable out through opening on bottom of base.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 16
11.4
When replacing power supply route drive power cable to underside of printer. Be sure it is not
pinched beneath or on side of power supply.
Section 12 - Drive Fan
12.1
Remove drive mount (see Drive Mount). Cut tie wrap securing fan and sata cables. Unplug drive
fan from mainboard.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 17
12.2
Remove 2 screws securing fan to inside of rear cover plate.
12.3
Tip printer up and remove drive fan, pulling cable out through opening on base. When replacing
fan, be sure cable is oriented to lower left as shown.

Allegro 100 Disc Publishing System
Service Manual
Rimage Corporation
Page 18
Front Hole
Section 13 – 光驱
13.1
卸下光驱支架(see Drive Mount)。 如下图标示，拧下固定要更换的光驱的4个螺钉。
13.2
从前面将光驱滑出。 将新的光驱滑入支架并用4颗螺钉固定（使用前组孔）。