rionet Joyton HB-G1E User manual

Battery Placement
1. Set the O-M2-M switch of the hearing aid to
"O" (power off).
2. Peel off the sticker on the positive side of
battery (PR48 or 13 zinc-air battery).
3. Open the battery holder with the tip of your
finger.
4. Insert the battery into the battery
holder. You do not have to worry
about the polarity.
5. Close the battery holder.
Battery life (PR48 or 13, for continuous use)
ANSI: Approx. 280 hours
IEC: Approx. 260 hours
- Battery life will change depending on the operating
condition.
Putting on Hearing Aid
1. Place the hearing aid on the ear.
zEarmold
HOW TO USE YOUR FIRST HEARING AID
zAny hearing aid cannot return level of your hearing to normal or
halt further hearing deterioration, but proper use of your hearing
aid can help you hear what is going on around you and let you
get more enjoyment of life.
zIf this is your first hearing aid, you - like most new users - will
probablybesurprisedattheloudnessofthesounds,andafterusing
itforashortwhile,youmayevenfeelthatitistoonoisy.Thefollowing
three tips are important in overcoming your concerns.
1) Read this manual and become familiar with the hearing aid's
various mechanisms and how to use them correctly.
2) First, use your hearing aid in a quiet place and listen to quiet
sounds and give yourself sufficient time to get accustomed to
the sound of your hearing aid.
3) If any physical problems develop, consult your doctor.
FOR KEEPING YOUR HEARING AID LONGER
zAlways keep the hearing aid clean. Clean the hearing aid with
dry cloth periodically and also remove earwax plugged in the
earpiece or earmold using eyebrush or toothbrush.
zDo not expose the hearing aid to the heat from stoves, etc. Also,
avoid leaving it in places with high humidity.
zOperate the controls with care. Do not press hard.
zIf the hearing aid is dropped in water, wipe with dry cloth and ask
the dispenser for check.
zDo not pick the microphone with nail, pin, etc., because this may
damage the microphone.
zDo not disassemble or attempt any repairs by yourself. Ask the
dispenser for repair.
OPERATING INSTRUCTIONS
Parts and Controls
3-20-41 Higashimotomachi, Kokubunji, Tokyo 185-8533, Japan
HB-G1E
zTube and earpiece shown above are not included as standard
accessories in some countries.
z* The communication connector serves for adjustment of the
hearing aid by the hearing aid professional.
DIGITAL
HEARING AID
zEarpiece
2. Turn the power on.
3. Adjust the volume control to a suitable level.
zVolume control
Higher numbers mean louder sound.
* Adjust the volume according to the situation (volume of
other voices, ambient noise, etc.).

TECHNICAL DATA (According to ANSI standard S3.22 2003)
Maximum-OSPL90 125 dB (1000 Hz)
HFA-OSPL90 122 dB
HFA-full-on Acoustic Gain 55 dB
Reference Test Gain 45 dB
Frequency Range 200 Hz to 5400 Hz
Equivalent Input Noise Level 21 dB
Total Harmonic Distortion 500 Hz: 2% 800 Hz: 2% 1600 Hz: 1%
AGC CRC (Input AGC)/OPC (Output AGC)
Operating Switch O-M2-M
Output Limiting Control OPC (range: 18 dB)
Tone Control TONE H, TONE L
Gain Control Main VR (range: 30 dB)
GAIN (range: 34 dB)
Battery Type/Supply Voltage 13/1.3 V
Battery Current 0.94 mA
Battery Life Approx. 280 hours
Dimensions/Weight 3.75 × 1.27 × 0.88 cm/4.0 g (excludingbattery)
(Typical value with E1 hook)
TECHNICAL DATA ()
Reference Test Frequency 1600 Hz
OSPL90 125 dB
500 Hz 122 dB
Peak 132 dB
Full-on Acoustic Gain 58 dB
Equivalent Input Noise Level 22 dB
Total Harmonic Distortion 500 Hz: 3% 800 Hz: 2% 1600 Hz: 2%
AGC CRC (Input AGC)/OPC (Output AGC)
Operating Switch O-M2-M
Output Limiting Control OPC (range: 18 dB)
Tone Control TONE H, TONE L
Gain Control Main VR (range: 30 dB)
GAIN (range: 34 dB)
Battery Type/Supply Voltage PR48/1.3 V
Battery Current 1.0 mA
Battery Life Approx. 260 hours
Dimensions/Weight 3.75 × 1.27 × 0.88 cm/4.0 g (excludingbattery)
(Typical value with E1 hook)
zMemory selection (using selector switch)
If sounds are hard to hear
depending on the environment,
such as in a noisy or quiet
environment, change the setting of
the memory selector to find the
position that yields best results.
* The memory selector switch (M2/
M) is programmed to match your
hearing pattern. Operate the switch
to find the position that yields best
results in a given situation.
zSwitch operation sound
Memory 1 Memory 2
M2ÆM: one beep M ÆM2: two beeps
Removing Hearing Aid
1. Set the switch to "O" (power off) before
removing the hearing aid. If the switch is left
No. 40240 04-10
in the "M" or "M2" position, acoustic feedback (howling) may
occur.
2. Be sure to set the switch to "O" and take out the battery,
when not using the hearing aid.
Turn-on precaution
If you switch the hearing aid off and then immediately on again,
there may be no sound, but this is not a defect. In such a case,
return the switch to "O" (Off), wait for at least 10 seconds, and
then set the switch to "M" or "M2" again.
Adjusting the Controls
This hearing aid is a digital type. To adjust it, a computer (with
NOAH and the Rionet Selector installed) and a HI-PRO unit are
required. Have the adjustment done at the dealer.
Factory Default Setting
zO - M2 - M switch : "O"
zVolume control (1 - 4) : "1"
According to IEC standard Pub. 60118-0-1983
Amendment 1-1994
Full-on gain curve
Frequency response curve and
effect of tone control OSPL90 curve and effect of
output limiting control
Full-on acoustic gain
frequency response curve
Basic frequency response curve
and effect of tone control OSPL90 curve and effect of
output limiting control