RioOutdoors 6S-SC User manual

1 | Page
Installation Instructions
6S-SC
6x6 Surface Mount Single Cubic Pergola Kit
Pergola Kits
WARNING: If the information in these instructions is not followed exactly, weakening or failure of the erected
structure may result causing property damage, personal injury, or loss of life.
All brackets designed and sold by RioOutdoors.com are to be used for building pergolas only and are not to be used for
other structure construction purposes.
•
Thoughtfully engineered
Brackets eliminate all wood-
joinery skills requirements.
•Skills required: drill holes
in concrete and hammer
in anchors, drilling pilot
holes and driving lag
screws into lumber.
•Easy lift and place U-
channels eliminate need
for lifting equipment.
Super-easy assembly
work.
•Self-aligning design
squares up structure
automatically.
•Estimated Assembly
Time is less than 1-hour.
Figure 1: Items included in the kit, (

 ).
Items not included in this kit: wood, tools, some hardware.

2 | Page
Table of Contents
1.1 SAFETY AND WARNING INFORMATION........................3
1.2 TOOLS REQUIRED...................................................4
1.3 CONTENTS OF KIT #6S-SC .......................................5
1.4 LIST OF MATERIALS THAT YOU WILL SUPPLY ..................5
1.5 SURFACE MOUNT SYSTEM........................................6
1.6 SIDE ELEVATION DIAGRAM....................................... 9
1.7 FLOOR ANCHOR BRACKETS INSTALLATION....... 10
1.8 INSTALLING PERGOLA POSTS........................... 12
1.9 POST-TOP BRACKETS INSTALLATION ........................ 14
1.10 6X6HEADERS INSTALLATION ................................. 17
2.1 CONDITIONS ...................................................... 20
2.2 EXCLUSIONS....................................................... 20
2.3 LIMITATIONS OF LIABILITY ..................................... 21
2.4 HOW TO OBTAIN WARRANTY SERVICE ..................... 21
Proper pilot hole diameter and hole depth for various lag screws and wood types
Lag Screw Type
Wood Type
Pilot hole drill diameter and hole depth
¼” X 1-1/4” Lag Screw
McMasterCarr.com SKU 92351A546
Soft Wood 3/32” drill bit diam., 1-1/4” depth
Hard Wood 3/16” drill bit diam., 1-1/4” depth
3/8” X 3” Lag Screw
McMasterCarr.com SKU 92351A636
Soft Wood 11/64” drill bit diam., 3” depth
Hard Wood ¼” drill bit diam., 3” depth
A properly sized pilot hole must be drilled before you attempt to drive lag screws into any pergola lumber member.
See Table, below. Driving lag screws into lumber, without first drilling a pilot hole, can prevent the lag screw from
driving fully into the wood or can lead to crack formation while driving the lag screw in, or later, as the wood dries
naturally. This can result in a weakened pergola structure.

3 | Page
GENERAL INFORMATION
1.1 SAFETY AND WARNING INFORMATION
1.1.1 Building Permit & Inspection Requirements
We recommend that you consult with your local building permit office and obtain advice and any required building permits and
inspection approvals from the local building inspection department or the local authority over building codes.
1.1.2 Other Cautions
CAUTION: Adhere to all safety requirements. Wear safety glasses/goggles when working. Wear safety gloves
when handling brackets, hardware, and lumber. Wear hearing protection when using a circular saw, miter
saw, table saw, or hammer drill.
INSTALLER: Leave this manual with the consumer. CONSUMER: Retain this manual for future reference.

4 | Page
1.2 TOOLS REQUIRED
Listed below, are common tools required for pergola projects. These tools are not included in this kit. Your pergola project may
not require all tools. Select and acquire the tools for your project from the “Required for” column in this table.
Description
Tool Purpose
Required for
Reference Image
Tape
Measure
Measure and verify
lengths. All pergola types
Framing
Level Verify Level/Plumb All pergola types
Hammer
Drill
Drill holes in concrete
pads or concrete
footing for securing
floor anchor brackets.
Drill pilot holes for lag
screws.
All pergola types
Ratchet
Socket
Driver
Drive lag screws into
Pergola lumber
members.
All pergola types
7/16” Hex
Socket
Drive ¼” X 1-1/4” Hex
Hd. lag screws. All pergola types
9/16” Hex
Socket
Drive 3/8” X 3” Hex Hd.
lag screws.
Raftered pergola (single,
dual, quad headers)
3/32” Drill
Bit
Drill pilot holes for ¼”
lag screws in soft wood. All pergola types
11/64” Drill
Bit
Drill pilot holes for 3/8”
lag screws in soft wood.
Raftered pergola (single,
dual, quad headers)
½” X 4”
Masonry
Drill Bit
Drill ½” X 2” deep holes
in concrete pads or
concrete footings.
Surface Mount styled
pergola
#2 Phillips
Screwdriver
Bit
Attaching pergola
rafter ties to rafters
and headers.
Raftered pergola (single,
dual, quad headers)
Circular
Saw/Miter
Saw
Cut headers to length;
cut rafters to length. All pergola types
Jig Saw
Cut rafter tail designs.
Raftered pergolas
Image not available.
Crescent
Wrench
Tighten down nut on
concrete anchors. Surface Mount Pergolas Image not available.
Hammer Various. All pergola types.

5 | Page
1.3 CONTENTS OF KIT # 6S-SC
The contents of this kit are shown in the table, below. Before you begin your project, take an inventory of all items that you
received from us. If any items are missing, contact us directly via email at [e-mail]. Include your name and
shipping address and your order number, if available. We will respond within 24 hours with a resolution to your problem.
Item SKU #, Description
Item Qty
Item Image
6x6 Post-Top/Floor 2-way Elbow Bracket
SKU# 6C2L 4
6x6 Fixed Floor Anchor Bracket
SKU# 6FA 4
¼ x 1-1/4” Lag Screw 64
1/2” X 2-3/4” (1/2-13 threads) Vibration Resistant
Hammer-On Stud Anchor for Concrete.
McMasterCarr.com SKU 92188A305
16
1.4 LIST OF MATERIALS THAT YOU WILL SUPPLY
This is the list of required materials which are not included in this kit. You will acquire these items locally for your project. Use
this table to help you calculate your total project budget.
Item Description Item Qty
Item Cost
($)
Total Item
Cost ($)
Item Image
6x6 Post Lumber (You determine length) 4
NA
6x6 Header Lumber (You determine length)
4
NA
3/8” x 3” SS Lag Screws (for deck mounting).
McMasterCarr.com SKU 92351A636 16
Tape, for marking drill bit depth
2”
NA
Grand Total Cost ($)
NA

6 | Page
1.5 SURFACE MOUNT SYSTEM
1.5.1 What is a Surface Mount system?
Surface Mount means that the vertical posts for a pergola are secured to the top of a concrete footings, concrete pad, or deck
cross-brace beams using Floor Anchor Brackets. You may bolt the floor anchor brackets directly on top of a concrete pad or on
top of a footing. If bolting on top of a deck, you must add cross-brace beams under the deck boards to fully support the weight of
the pergola.
For concrete footings, the required depth is determined by the maximum depth of the frost line for a particular area. The
diameter of the footing is determined by the weight that each footing is subjected to by the pergola structure. This pergola
weighs approximately 500 lbs. If you choose to use concrete footings or to add this pergola on top of an existing wooden deck,
consult your local building permit office to determine the required footing depth and diameter and the cross-brace beam
requirements. If you fail to follow local officials’ guidelines, permanent damage to the Pergola structure or the deck structure can
render them unsafe for use.

7 | Page
1.5.2 Study the Floor Anchor Brackets layout requirements.
First, study the Flooor Anchor Brackets layout requirements. Spend some time planning, yourself, so you are fully familiar with the
final size you desire for your pergola. Determine the exact location for each pergola Floor Anchor Bracket based on your pergola
size. We have designed our pergola systems to eliminate the need to cut any 6x6 post or header members. Plan accordingly to
minimize your work requiremens.
Mark each Floor Anchor Bracket location using colored chalk and tracing the outer profile of the Floor Anchor Bracket bottom
plate on top of the concrete pad or wood deck. Remeasure and verify the proper location for each post. If planning to use
concrete footings, mark the bracket locations on the ground using stakes or bright spray paint.

8 | Page
1.5.3 Call 811.
811 is the national call-before-you-dig phone number. Anyone who plans to dig should call 811 or go to their state 811 center's
website before digging to request that the approximate location of buried utilities be marked with paint or flags so that you don't
unintentionally dig into an underground utility line.
Consult with your local building permit office and obtain any required building permits and formal information related to
required footing depth and diameter for your locality.
1.5.4 Install the Surface Mount footing
system.
1. Excavate the required hole diameter and depth.
2. Pour concrete into the footing holes.
3. Work in 6” incremental depths. Tap concrete
with the tip of a trowel to remove air bubbles.
Work upward until you reach ground level or 1”
above ground level.
4. Along the outer 2-3 inches create a downward
tapered profile moving away from the footing
center in all directions on the concrete top
surface. This taper will help water flow away
from the post bracket.
5. Wait 7 days for the concrete footing to cure
before proceeding with the remaining
construction work. If quick-setting concrete is
used, cure times may be shorter; read the
information on the concrete bag or ask your
concrete supplier.
Figure 2: Tapered Footing Top
Surface.

9 | Page
1.6 SIDE ELEVATION DIAGRAM
Based on the height of the post used, the diagram below provides the side elevation profile for this pergola system.
POST HEIGHT
DIM A
DIM B
96
96
90.5
108
108
102.5
120
120
114.5
132
132
126.5
144
144
138.5
Dim A, above, is the height of the post used. Dim B is the inner ceiling height of the pergola. Dim B is measured to the bottom
surface of the header member.

10 | Page
1.7 FLOOR ANCHOR BRACKETS INSTALLATION
1.7.1 Concrete Footing or Concrete Pad Anchoring
1. Place a floor anchor bracket at the designated location and orient it in the proper way.
2. Apply tape to the drill bit to mark the 2” depth required for the 2-3/4” Vibration Resistant Hammer-On Stud Anchor you
will be using to anchor the bracket to the concrete footing or pad.
3. Drill into the concrete through the four holes in the bracket bottom plate and into the concrete using a hammer
drill and ½” masonry drill bit. Drill minimum 2-1/4” deep and maximum 2-3/8” depth. Do not drill less than 2-1/4”
depth as the anchor will not pinch the bracket down fully if the hole is less than 2” deep.
4. Using compressed air, blow out the drilling dust out of all holes. Compressed air cans are available at most stores.

11 | Page
5. Hammer in one concrete anchor (1/2” X 2-3/4”) into each hole you drilled through the hole in the Floor Anchor
floor bracket.
6. Tighten down the nut using a crescent wrench.
7. Repeat steps 1-6 for all Floor Anchor Brackets.
1.7.2 Anchoring on existing deck
Consult your local building permits office. Do not proceed without consulting your building permit office. It is important
to be cautious when installing a pergola on top an existing wooden deck. You must plan to add extra cross-support
beams for low weight pergolas, like cubic shaped pergolas. For heavier pergolas, like raftered pergolas, you must plan
and add additional support posts directly under the pergola posts which will transfer the pergola load to the ground. At
the ground level, a concrete footing must be added per local code requirements to provide permanent support to the
posts. Your building permit office is the best free information source.

12 | Page
1.8 INSTALLING PERGOLA POSTS
1. Slide one 4x4 post inside a Floor Anchor. Let gravity pull the post all the way down.
2. Identify the 5/16” holes in two opposite faces in the floor anchor square tube (two holes in each face).

13 | Page
3. Drill 3/32” x 1-1/4” holes at the center of each 5/16” hole (four holes total, see step 2).
4. Drive a ¼” X 1-1/4” lag screw through each pilot hole using a rachet and 7/16” socket. Tighten down all lag screws.
5. Repeat steps 1 to 4 for all vertical posts.

14 | Page
1.9 POST-TOP BRACKETS INSTALLATION
Begin by identifying the brackets and screws.
1. Slide the 2-way elbow bracket’s tube over the 6x6 post top after aligning the header receiver u-channels in the proper
direction. Let gravity work and pull the bracket all the way down on top of the post.
2. Identify the four 5/16” holes which are on the sides of the gussets in the bracket.
Figure 4: Identify four 5/16" holes.
Figure 3: Slide Elbow Bracket over Post-Top.

15 | Page
3. Wrap a piece of electrical tape around the drill bit, spaced 1-1/4” from the drill bit tip. This will act as a hole depth indicator
when you drill each pilot hole. Pilot holes should be drilled at least 1-1/4” deep. A little bit deeper is acceptable but do not
drill less than the required 1-1/4” depth.
4. Drill 3/32” X 1-1/4” deep pilot holes at the center of four 5/16” Holes. Locate pilot holes at the center of each 5/16”
hole.
Figure 5: Wrap tape around drill bit to mark hole depth.
Figure 6: Drill pilot holes.

16 | Page
5. Drive one ¼ x 1-1/4” Hex Lag Screw through each 5/16” hole into the pilot holes you drilled in step 4, using a 7/16”
Socket and Rachet driver. Tighten down each screw.
6. Repeat steps 1 through 5 for each post top bracket.

17 | Page
1.10 6X6 HEADERS INSTALLATION
1. Lift and place one 6x6 header into the U-channels of adjacent post-top bracket.
2. Locate the two 5/16” holes on each vertical face of the U-channels holding the 6x6 header. Drill 3/32” X 1-1/4”
deep pilot holes at the center of four 5/16” Holes. Locate pilot holes at the center of each 5/16” hole.

18 | Page
3. Drive one ¼ x 1-1/4” Hex Lag Screw through each 5/16” hole into the pilot holes you drilled in step 8, using a 7/16”
Socket and Rachet driver. Tighten down each screw.
4. Repeat steps 1-3 for the remaining 3 headers.

19 | Page
Your Cubic Pergola construction project is now complete. Let us know how the construction project went for you.
Was it easy to do? Did parts fit easily and properly? Do you like the quality of our products and design styles? Is
your pergola structure sturdy and strong? Please go to RioOutdoors.com and provide us with your review.
You may add accessories such as a swing or hammock, 2x4 beams or 2x6 rafters on top for shielding direct
sunlight, or a sunshield fabric on top. Order accessories at RioOutdoors.com.
Thank you for being a RioOutdoors.com customer.

20 | Page
WARRANTY POLICY STATEMENT
RioOutdoors.com, extends this 1-Year Warranty to the original purchaser, automatically upon purchase from RioOutdoors.com.
The items covered by this warranty and the period of such coverage is set forth in the table below.
Some conditions apply (see below).
The policy is not transferable, amendable, or negotiable under any circumstances.
Part 1 year
Labor
Coverage
Welded Steel Brackets

Not Included
Painted Finishes

Not Included
All hardware

Not Included
2.1 CONDITIONS
Warranty protects against defect in manufacture only, unless herein specified otherwise.
Any part(s) found to be defective during the warranty period as outlined above will be repaired or replaced at RioOutdoors.com’s
option provided that the defective part is returned, if requested by RioOutdoors.com. Alternatively, RioOutdoors.com may at its
own discretion fully discharge all its obligations under the warranty by refunding the verified purchase price of the product to the
original purchaser.
RioOutdoors.com is not responsible for results or costs of workmanship of installers in the negligence of their construction work.
At all times RioOutdoors.com reserves the right to inspect reported complaints on location in the field claimed to be defective
prior to processing or authorizing of any claim. Failure to allow this upon request will void the warranty.
All claims must be complete and provide full details as requested by RioOutdoors.com to receive consideration for evaluation.
Incomplete claims may be rejected.
All pergola brackets must be installed according to all manufacturers’ instructions as per the installation instruction manual by a
RioOutdoors.com.
All Local and National required codes must be met.
Repair/replacement parts purchased by the consumer from RioOutdoors.com after the original coverage has expired will carry a
90-day warranty, valid with a receipt only. Any item shown to be defective will be repaired or replaced at our discretion. No labor
coverage is included with these parts.
2.2 EXCLUSIONS
This 1-Year Warranty does not extend to paint, rust, or corrosion of any kind due to corrosive chemicals (i.e., chlorine, salt, air,
etc.), physical damage to painted surfaces during installation or later.
Malfunction, damage, or performance-based issues of all components as a result of environmental conditions, location, chemical
damages, downdrafts, installation error, installation by an unqualified installer, abuse, misuse, use of improper tools, acts of God,
weather related problems from hurricanes, tornados, earthquakes, floods, lightning strikes/bolts or acts of terrorism or war,
which result in damage are not covered under the terms of this 1-Year Warranty.
RioOutdoors.com has no obligation to enhance or modify any part once manufactured (i.e., as products evolve, field
modifications or upgrades will not be performed on existing pergolas).
Any parts showing signs of abuse or misuse will not be covered under the terms of this warranty policy and may void this
warranty. This includes parts with rusted or corroded surface or welds which have not been reported as rusted or corroded
within three (3) months of installation/purchase.