RIOTEC DC9257LP User manual

1
Quick Guide
--DC9257LP (with Battery)
-DC9257LN (without Battery)
1
H92P
Connect to micro USB port of OTG device
2 H92P/H92N
3

* Before you use scanner, please switch to "C" for battery
charge for 3~4 hours.
*Under “C mode”, you can raise/lower soft-keyboard easily.
4

H92P Scan Holder is with Li-Ion battery inside. When in
charging, please use the original power adaptor of OTG
device (recommend). Through it, it charges both OTG
device and H92P internal battery at the same time. When in
low battery (Red LED flashing), please charge it
immediately.
LED Indicator Information
Green LED OFF Full charged (Charge mode)
Green LED ON Charging (Charge mode)
Red LED Flashing Low battery (Operation mode)
Attention: Under “Operation mode” please do not charging,
otherwise the OTG device's battery will be charging back to
H92P’s battery.
5


The touch trigger is in the central area of mini scanner. (for both side).
Please check the above drawing for your reference.
Installation
Before using scanner, please make sure that the OTG device is fully
charged.
1. Under USB HID interface
** When plugged into OTG device, it will be recognized and begin
to scan the barcode.
2. Under USB Serial interface
** Please install PL-2303 driver into your OTG device first. PL-2303
driver can be downloaded from Google Play
** Connect scanner to your OTG device, then, you can know which
serial port scanner connects to.
** The data you scan will be sent to serial port and your APP can
get the data from serial port directly.
Trigger
Area
O = Operation mode C = Char
g
e mode
LED Indicator

Suction Cup
PU Glue
(Can be used
repeatedly)
Micro USB
cable (OTG)
Mini
scanner
Micro USB
Micro USB
H92P with
Li- Ion Battery/
H92N without
Battery
LED Indicator
H92P only

2
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have scanned the
incorrect codes, please scan from A1 to A3 for USB HID or B1 to B5 for
RS232 or USB Serial. This will reset the scanner to its factory defaults.
A1 B1
A2 B2
A3 B3
B4
B5
*Note: Please install PL-2303 driver for USB Serial.
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
Keyboard Country (For USB HID only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
Bel
g
ium Spain
Germany
Austria
Russia
Sweden Portu
g
al
Keyboard Country (For USB HID only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
US
A
Japan
Denmark
Finland
France
U
K
Italy
Norway
T
urkey F
T
urkey
Q

3
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
1D Symbologies – 1
ENABLE
Code 93
DISABLE
ENABLE
Code 39 DISABLE
1D Symbologies – 2
ENABLE
UPC-E
DISABLE
ENABLE
UPC-A
DISABLE
ENABLE
Interleaved
2 of 5
DISABLE
ENABLE
Code 128
DISABLE
ENABLE
GS1-128
UCC/EAN-128
DISABLE
1D Symbologies – 3
ENABLE EAN-8 DISABLE
ENABLE EAN-13 DISABLE
ENABLE Codabar DISABLE
ENABLE ISSN DISABLE
ENABLE ISBN DISABLE
ENABLE
GS1-Databar
(RSS) DISABLE

4
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
2D Symbologies
ENABLE
Data
Matrix DISABLE
ENABLE
QR Code DISABLE
ENABLE
Micro
QR Code DISABLE
ENABLE
PDF 417 DISABLE
Inter-Keystroke Delay (For USB HID only)
This parameter specifies the delay between emulated keystrokes.
No Delay
Short Delay
(20ms)
Long Delay
(40ms)
 Information in this document is subject to change without notice.
 For more information, please visit:
www.riotec.com.tw
R_200225_01