RIOTEC RIOSCAN iLS6303AS User manual

1
RIOSCAN Laser Barcode Scanner
Quick Guide
Model no.:
iLS6303AS
Introduction
Designed primarily for smartphone, the iLS6303AS is a 1D
barcode scanner that allows you to scan various barcoded
items and send data to smartphone.
Its in-built 1D Laser Engine allows you to reliably read 1D
barcodes on various shapes and is a great space-saver for
busy or limited workspaces.
It supports not only iOS devices through Bluetooth
communication, but also Android OTG devices through USB
cable
Delivery content
* Bluetooth Barcode scanner x 1
* Charging cradle x 1
* PCB material board+3 screws x 1
* Holder for smartphone x 1
* USB cable x 1
* Quick instructions x 1
Limited Warranty
Riotec provides a one year limited warranty.
This warranty does not cover any product which has been subject
to improper use, neglect or unauthorized repair or installation.
This warranty does not cover consumable parts. (Cables &
batteries are consumables.)
Safety instructions
* The product is equipped with a Class 1 laser.
* Never look into the laser beam and never point it at people or
animals. Laser radiation can seriously damage your eyes.
* Do not point the laser beam at mirrors or other reflective surfaces.
The uncontrolled, reflected beam may strike people or animals.
* Don’t put scanner in places excessively high temperatures, such as
expose under direct sunlight.
* Don’t use scanner in extremely humid area or drastic temperature
change
* The rechargeable battery is permanently built into the product and
cannot be replaced.
* Never damage the rechargeable battery. Damaging the casing of
the rechargeable battery might cause an explosion or a fire!
Charging:
1. Please switch on and charge scanner for 3~4 hours before first use
as shown on Fig.
2. When user charge smartphone & scanner, please use smartphone
original USB power adapter
3. The cradle functions as a charger for the scanner. Even if the
scanner’s battery is full, the cradle will continue to supply power to
the scanner. We suggest removing the scanner from the cradle
when fully charged.
4. When you charge scanner & smartphone, please enter Wired OTG
mode & switch to “C- Charging mode”.

2
iLS6300FS supports BT communication mode (for iOS) and wired
OTG communication mode (for Android OTG devices)
If you want to switch to another mode, please read the below configuration
code first.
Bluetooth communication
wired OTG communication mode
(default)
Operating elements
* Please switch ON and charge scanner for 3~4 hours at first
time before use.
How to Connect to Smartphone via BT
1. Make sure the default is BT mode (page #2) & your device
has BT HID or SPP profile
2. Turn off Power-Saving mode on your smartphone/tablet
3. Then, choose HID or SPP profile and scans the following 2
settings codes before connecting to smartphone/tablet.
(A1  A2 or B1  B2)
If you don’t know which profile to choose for your device, try
HID first, then, SPP.
HID profile SPP profile
A1 B1
A2 B2
4. Please complete the connection procedures as the above
photos.
5. After the devices are paired, the screen will show
“Connected”. (see step #6 above)
6. Before using WordPad file or appropriate APP, please set
keyboard language of device to US English. Then, scan the
barcodes and the barcode data will show on the cursor side. If
the data cannot be sent to smartphone/tablet, please scan the
“Reset Configuration to Defaults” setting codes (on page #3).
1. click the “Settings” 2. click “General”
3. click “Bluetooth” 4. Turn it ON, and search the
Devices
5. Select “Rxxxxxx” to connect 6. When see the “Connected”
means the connection is OK.
(example: pairing with iPhone)
Tri
gg
er / Power ON
Button
(For iOS Device ONLY)
Press the trigger for 4~5
seconds to raise and
lower soft-Keyboard
Exit
Window
Micro USB port
Use Micro USB cable to
connect to smartphone.
Char
g
in
g
cradle
Indicator
(LED)

3
Notes 1:
* This product complies with Bluetooth standards. This device used
with this product must support the same SPP or HID standard. For
Bluetooth devices with other profiles we cannot guarantee a
connection before the product has been tested.
* The communication speed and range of the product may vary due to
obstacles and radio interference between the product and device.
Condition on the host device may also effect the communication
speed and range of the scanner
Note 2:
* When the battery power is too low, the Orange LED will flash
and beep once. Scanner should be charged immediately. If
scanner shuts down it is recommended to charge it fully then
power it back on.
Reset Configuration to Defaults
(scan from A1 to A3 for HID or B1 to B2 for SPP profile)
HID profile SPP profile
A1 B1
A2 B2
A3
How to Connect to Smartphone via OTG cable
1. Make sure you enter wired OTG mode (page #2) and your
Android device supports OTG functionality.
2. Make sure scanner is in ”O” (OPERATION MODE) (see below)
3. Connect scanner to Android OTG device through micro USB cable.
4. Scan the barcode
5. Open app on smartphone/tablet & data will be sent to the app
directly
After the scanner connects to your iOS device and is inserted into
cradle, it may display the above message.
If this happens, remove and reinsert device into cradle.
LED Indicator Information
Orange LED ON Full charged
Orange LED Flashing Charging / Low battery
Red LED ON Offline / out of service
Green LED ON Good read
Orange LED ON Good read (Batch mode)
Before enterin
g
BT mode, you
must switch to right
“
Charging mode” first.
T
hen, cradle can supply
power to iOS / Android device
(through micro USB cable) &
scanner simultaneously.
Indicator (LED)
Please check the “LED
Indicator Information” on
page #3
Switch to left:
“
O” (Operation mode)
(data transmission)
Switch to right:
“
C” (Charging mode)
Indicator (LED)
Please check the
“
LED Indicator
Information”

4
Wired OTG- configuration code
Before use wired OTG communication, you must read the below
setting code according to your application.
HID USB Serial
HID mode:
 Plug & Play. No extra driver is needed.
SPP mode:
 must install PL-2303 driver to smartphone first.
 Smartphone will recognize scanner automatically under
USB Serial mode
** Data output must be under “O – operation mode”
How to charge
(through Micro USB port or Type- C port)
A. Configuration code for charging
According to your charging cable (micro USB cable or type-C
cable), please scan the below setting code first.
Type C Micro USB
B. Attention:
1. Please use the ORIGINAL USB cable & power adapter (of
smartphone) to charge device.
2. According to different smartphones, you must use corresponding
USB cable & configuration code for charging.
3. Cannot plug micro USB cable & Type C cable to cradle for
charging at the same time.
4. If you don’t follow the above instruction, quick charging or OTG
function will lose their functions.
Keyboard Country
(Wired OTG mode only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
USA
(Original setting)
Italian
Norway France
Germany Vietnam
Sweden Spain
Denmark
P
ortu
g
al
Switzerland Hun
g
ary
1. Place the mobile device holder by having the side of open and
close red switch on the right side of the scanner as presented on
the above image.
2. CAUTION: Please do not pull or press on any of the 4 extensions
or legs of the holder, for it can unbalance and disrupt the normal
function of the holder’s 4 extensions.
Place the mobile device holder lightly on the top of the base, so the 4
elevated studs fit into the 4 holes of the holder.
Holder’s back with 4 holes to fit on
and lock up with the 4 studs the
scanner. 
4 Elevated Studs to fit into the
4 holes of the Holder’s back.
Holder’sfrontside:Makesurethered switchisontheright
side(exactlyastheabovepictureshows),whenfittingthe4
holesoftheholdertothe4studsofthescanner
Micro USB
Charging port
Type C
Charging port

5
3. Press the holder to the scanner firmly and draw back very
carefully until you hear a low clicking sound.
4. To separate the holder from the scanner: Press on the holder
towards the scanner firmly, then push it forward carefully.
5. IMPORTANT: We do not recommend the repetitive action of
detaching and reattaching the holder.
6. Place the smartphone onto holder (Recommendation: use
mobile device less than 14.5 cm in length), plug the micro usb to
the mobile device, then close in the extensions.
7. Push in the tiny rectangular switch at the bottom of the handle,
then switch the scanner to Operation mode, now it can scan
directly to the mobile’s APP. The user may choose to connect
through Bluetooth as well (Please review the different ways of
connection at page 2 and 3, for a more detail explanation).

There are two operating modes on the scanner
1.Data Transmission mode(Default)

It is a necessary to scan
“
clean memor
y
data
”
when
switching between these two modes.
Within Bluetooth radi
o
ran
ge
Beyond Bluetooth radio ran
ge
Data
read
Transmit data to
smartphone/tablet directly
Save data in scanner’s memory,
scanner will transmit data to
smartphone/tablet automatically
after getting back to Bluetooth
radio range.
Enter Data Stora
g
e mode
LED Green/ Oran
g
e LED flashes,
followed by 3 beeps.

2. Data Storage mode(Batch Mode)



It is a necessary to scan
“
clean memor
y
data
”
when
switching between these two modes.
Data
read
Save data directly to scanner’s memory. It will transmit data to
smartphone/tablet after you scan the Transmit memory data
code. To delete data, please scan the Clean memory data code.
Enter Data Transmission mod
e

LED Green/ Oran
g
e LED
f
lashes followed by 3 beeps.
Always Clean memory data before switchin
g
to Data Transmission
Mode.
Otherwise Red/ Orange LED will flash with one long beep sounds
and will not switch modes.

A
. Data Transmission mode
(Default)
1. When you are out of BT signal range,
the data you scan will be saved to
memory. Once you are back within
range, the data will be sent to
smartphone/tablet automatically.
B. Data Storage mode(Batch mode)
1. Data Storage mode (Batch mode):
When you scan the barcodes, the data
will be saved directly to scanner’s
memory. After you scan the
“Transmit memory data” code
(above right), the data will be sent to
smartphone/tablet.
2. Before you can continue to scan or
switch modes, you must first delete
the data stored in the memory. To do
this, scan the “Clean memory data”
code. (below right)
Transmit memory data
Green/Oran
g
e LED flashes
followed by 3 beeps
The barcode data which is stored
in the memory will be sent to
smartphone/tablet directly.
(under Batch mode, within
Bluetooth service range)
Clean memory data
Green/Oran
g
e LED flashes
followed by 3 beeps.
The barcode data which is stored
in the memory will be deleted. You
can then switch modes.

Transmission Speed
Transmission speed is dependent on your device. In order not
to lose data, please choose the correct speed. Middle-speed is
the Default.
High-speed transmission
(for HID, SPP)
Middle-speed transmission
(for HID only, HID Default)
Slow-speed transmission
(for HID/SPP, SPP Default)
Ultra Slow-speed 1
transmission
(for HID only)
Ultra Slow-speed 2
transmission
(for HID only)
Ultra Slow-speed 3
transmission
(for HID only)
1.Holder’sfrontside:Shift
andHoldtheredswitchto
Openwhileyourotatethe
wheeleitherway,inorderto
shrinkorspreadthe4
extensions.
2.Donotpullorpushthe4
extensions,norextendthe
wheelacrossthelimit,forit
candisruptthebalanceand
functionalityoftheholder.
3.Usemobiledeviceless
than14.5cminlength.

6
Power-saving Mode
Power-saving mode OFF
Powe
r
-savin
g
mode ON
(Default): Enter power-saving
mode after one minute inactivity.
This function conserves battery
power. When you press the
"SCAN/Power ON" button, it will
wake up and begin to scan.
* When charging, the scanner will not enter power-saving mode
automatically.
Battery information
When you scan this settin
g
code, scanner will output the
battery information to device.
Output battery information
automatically – Enable
Will send data to device
every 30 seconds.
Output battery information
automatically – Disable.
The output format of battery information is as below:
For example: %^4^%
%^NUMBER^% Number is from 0~4.
4 means 80%~100%
3 means 55%~80%
2 means 30%~55%
1 means 10%~30%
0 means under 10% -- When output reads “0”, it means low
battery power and device should be charged immediately.
1D Symbologies -1
ENABLE CODABA
R
DISABLE
ENABLE Code 39 DISABLE
ENABLE Code 32 DISABLE
ENABLE Code 39
FULL ASCII
DISABLE
ENABLE Interleaved 25 DISABLE
ENABLE Code93 DISABLE
ENABLE Matrix 25 DISABLE
1D Symbologies -2
ENABLE MSI DISABLE
ENABLE CODE128 DISABLE
ENABLE GS1-128 DISABLE
ENABLE TELEPEN DISABLE
ENABLE UPC-A DISABLE
ENABLE EAN-13 DISABLE
ENABLE EAN-8 DISABLE

7
1D Symbologies -3
ENABLE
GS1
Omnidirectional DISABLE
ENABLE
GS1 DataBar
Limited DISABLE
ENABLE
GS1 DataBar
Expanded DISABLE
ENABLE
CHINA POST
DISABLE
ENABLE PLESSY CODE DISABLE
ENABLE INDUSTRIAL 25 DISABLE
ENABLE IATA 25 DISABLE
Quick guide is subject to change without notice. R_200326_01