RIOTEC iLS6303XBU User manual

1
Programming Q uick Guide
iLS6303XBU/iLS6303XB
Connecting the Scanner
Be sure that PC is turned OFF, before Connect scanner cable to
the PC USB port on the PC as below described, Ensure that all
connections are ready, turn on your PC
1. Please switch ON and charge scanner for 4~5 hours at first time
before use. Scanner switch shown on Fig. 2.
2. After switch ON, the Orange LED will flash following with 3
beep-sounds. The RED LED will be OFF while it links to cradle
within 2.4GHz radio range.
3. If RED LED is continual ON, please re-plug USB cable, then, scan
the 3 barcodes on the bottom of cradle sequentially. (Shown on
Fig. 3 from 1 to 3). If you are unable to complete this setting within
1 minute, please re-plug USB cable & re-start the scanner, and try
again.
4. Charging issue: Cradle works as charger when putting scanner on
it. Even if the scanner's battery is full, the cradle will continue to
supply power to the scanner. We suggest you to remove scanner
from cradle when scanner is charged fully
*Note: Please install PL-2303 driver for iLS6303XB
LED Indicator Information
Orange LED ON
Full charged
Orange LED Flashing
Charging / Low battery
Red LED ON
Off line / out of service
Green LED ON
Good read
Remark:
*When the battery power is too low, the Orange LED will flash
and beep once. Scanner should be charged immediately.
*If scanner shuts down it is recommended to charge it fully
before turning it back on.
*Under power-saving mode, there will not be LED indication
when charging.
Reset Configuration to Defaults
(scan from A1 to A2 for iLS6303XBU or B1 to B3 for iLS6303XB)
iLS6303XBU
iLS6303XB
A1
www.tec-it.com
.
B1
www.tec-it.com
.
B2
Demo
.
A2
Demo
%D%F%T
B3
Demo
%D%F%T
*Note: Please install PL-2303 driver for iLS6303XB
Trigger Mode
Demo
%R%T%E
Trigger always
(Trigger available at any time)
Demo
%R%T%D
Trigger standard (Default)
(Trigger available, after data sent to the
device)
Transmission Speed
Transmission speed is dependent on your device. In order not to lose
data, please choose the correct speed. Middle-speed is the Default.
Demo
%B%T%H
Demo
.
High-speed
Ultra Slow-speed
transmission
1transmission
Demo
.
Demo
.
Middle-speed
Ultra Slow-speed
Transmission
(Default)
2transmission
Demo
%B%T%L
Demo
.
Slow-speed
Ultra Slow-speed
Transmission
3transmission
Bluetooth Auto-connection
Demo
%A%L%E
Bluetooth Auto-connection ON:
When out of range, it will keep trying to
connect to device, scanner will not enter
power-saving mode.
Demo
%A%L%D
Bluetooth Auto-connection OFF:
When you are out of BT signal range, scanner will
stop sending auto-connection signal to device
after 2 minutes. During this time, it will not enter
power-saving mode.
Once you are back within range, press trigger to
connect to the device. (Default)

2
Keyboard Country(For USB HID only)
Scan the appropriate country code as below to program the keyboard
layout for your country or language. As a general rule, the following
characters are supported, but need special care for countries other
than the United States: @ | $ # { } [ ] = / ‘ \ < > ~
%+-$.00
%+-$.06
USA
(Original setting)
Italian
%+-$.01
%+-$.07
Norway
France
%+-$.02
%+-$.08
Germany
Vietnam
%+-$.03
%+-$.09
Sweden
Spain
%+-$.04
%+-$.10
Denmark
Portugal
%+-$.05
%+-$.11
Switzerland (F)
Hungary
%+-$.12
%+-$.18
Latin America
Icelandic
%+-$.13
%+-$.19
Brazil
Poland
%+-$.14
%+-$.20
Belgium
Turkey F
%+-$.15
%+-$.21
Bulgarian Latin
Turkey Q
%+-$.16
%+-$.22
Finland
Japan
%+-$.17
%+-$.23
Netherlands
Korea
%+-$.24
%+-$.26
Thai
Russia
%+-$.25
Switzerland German
*The different keyboard language option starts from June. 2017.
Power-saving Mode
Demo
%P%D%T00
Power-saving mode OFF
Demo
%P%D%T03
Power-saving mode ON (Default):
Enter power-saving mode after 3-minute inactivity.
This function converses battery power. When you
press "SCAN/Power ON" button, it will wake up and
begin to scan.
Demo
%P%D%T10
Power-saving mode ON:
Enter power-saving mode after 10-minute
inactivity. This function converses battery power.
When you press "SCAN/Power ON" button, it will
wake up and begin to scan.
*When charging, the scanner will not enter power-saving mode
automatically
How to append a “prefix” or a “suffix” to the
barcode data
Demo
%C%P%S
Demo
%C%S%S
prefix
suffix
1. scan above configuration code for Prefix or Suffix
2. enter the required values (right, numeric barcode) for Prefix or
Suffix using the hex values for the desired HEX values from “Prefix
& Suffix TABLE (blew page)”
3. then, end by scanning Code X (below, right)
*The max. of special characters is 5.
*When you append 1~4 required values for Prefix or Suffix, it must
end with Code X.
*It doesn’t need Code X, if you append 5 values to barcode data.
How to delete Prefix or Suffix
1. scan above configuration code for Prefix or Suffix
2. enter the “0” “0” (above, right)
3. then end by scanning Code X (below, right)
Numeric barcode for settings
Demo
0
Demo
6
Demo
C
Demo
1
Demo
7
Demo
D
Demo
2
Demo
8
Demo
E
Demo
3
Demo
9
www.tec-it.com
F
Demo
4
Demo
A
Demo
5
Demo
B
Demo
X

3
Prefix & Suffix TABLE
HEX
HID
(SPP)
HEX
HID
(SPP)
HEX
HEX
HEX
HEX
01
CTRL A
(SOH)
19
CTRL Y
(EM)
20
SPACE
38
8
50
P
68
h
02
CTRL B
(STX)
1A
CTRL
Z(SUB)
21
!
39
9
51
Q
69
i
03
CTRL C
(ETX)
1B
ESC
(ESC)
22
"
3A
:
52
R
6A
j
04
CTRL D
(EOT)
1C
CTRL \
(FS)
23
#
3B
;
53
S
6B
k
05
CTRL E
(ENQ)
1D
CTRL ]
(GS)
24
$
3C
<
54
T
6C
l
06
CTRL F
(ACK)
1E
CTRL ^
(RS)
25
%
3D
=
55
U
6D
m
07
CTRL G
(BEL)
1F
CTRL _
(US)
26
&
3E
>
56
V
6E
n
08
Backspace
(BS)
27
'
3F
?
57
W
6F
o
09
Tab
(HT)
28
(
40
@
58
X
70
p
0A
CTRL J
(LF)
29
)
41
A
59
Y
71
q
0B
CTRL K
(VT)
2A
*
42
B
5A
Z
72
r
0C
CTRL L
(FF)
2B
+
43
C
5B
[
73
s
0D
Enter
(CR)
2C
,
44
D
5C
\
74
t
0E
CTRL N
(SO)
2D
-
45
E
5D
]
75
u
0F
CTRL O
(SI)
2E
.
46
F
5E
^
76
v
10
CTRL P
(DLE)
2F
/
47
G
5F
_
77
w
11
CTRL Q
(DC1)
30
0
48
H
60
`
78
x
12
CTRL R
(DC2)
31
1
49
I
61
a
79
y
13
CTRL S
(DC3)
32
2
4A
J
62
b
7A
z
14
CTRL T
(DC4)
33
3
4B
K
63
c
7B
{
15
CTRL U
(NAK)
34
4
4C
L
64
d
7C
|
16
CTRL V
(SYN)
35
5
4D
M
65
e
7D
}
17
CTRL W
(ETB)
36
6
4E
N
66
f
7E
~
18
CTRL X
(CAN)
37
7
4F
O
67
g
Reading Techniques
The view finder projects an aiming
beam that should be centered over the
bar code, but it can be positioned in
any direction for a good read.
*Hold the scanner over the bar code, pull the trigger, and center the
aiming beam on the bar code.
*The aiming beam is smaller when the scanner is closer to the code
and larger when it is farther from the code.
1D Symbologies On/OFF -1
ENABLE
Codabar
DISABLE
Demo
.
Demo
.
ENABLE
Code 39
DISABLE
Demo
.
Demo
.
ENABLE
Code 39
Full ASCII
DISABLE
Demo
.
Demo
.
ENABLE
Interleaved
2 of 5
DISABLE
Demo
.
Demo
.
ENABLE
NEC 2 of 5
DISABLE
Demo
.
Demo
.
1D Symbologies On/OFF -2
ENABLE
Straight 2 of 5
Industrial
DISABLE
Demo
.
Demo
.
ENABLE
Straight 2 of 5
IATA
DISABLE
Demo
.
ww w.tec-it.com
.
ENABLE
Matrix
2 of 5
DISABLE
Demo
.
Demo
.
ENABLE
GS1-128
DISABLE
Demo
.
Demo
.
ENABLE
UPC-A
DISABLE
Demo
.
Demo
.
ENABLE
UPC-E
DISABLE
Demo
.
Demo
.
ENABLE
Code 11
DISABLE
Demo
.
Demo
.
ENABLE
Code 93
DISABLE
Demo
.
Demo
.

4
1D Symbologies On/OFF -3
ENABLE
Telepen
DISABLE
ww w.tec-it.com
.
Demo
.
ENABLE
GS1 DataBar
Omnidirectional
DISABLE
Demo
.
Demo
.
ENABLE
GS1 DataBar
Limited
DISABLE
Demo
.
Demo
.
ENABLE
GS1 DataBar
Expanded
DISABLE
Demo
.
Demo
.
ENABLE
MSI
DISABLE
Demo
.
Demo
.
ENABLE
Trioptic
Code
DISABLE
Demo
.
ww w.tec-it.com
.
ENABLE
EAN-13
DISABLE
Demo
.
Demo
.
ENABLE
EAN-8
DISABLE
Demo
.
ww w.tec-it.com
.
ENABLE
Code 32
DISABLE
Demo
.
ww w.tec-it.com
.
*If you are going to scan Code 32, Trioptic Code must be off.
2D Symbologies On/OFF
ENABLE
Codablock A
DISABLE
Demo
.
Demo
.
ENABLE
Codablock F
DISABLE
Demo
.
Demo
.
ENABLE
PDF 417
DISABLE
Demo
.
Demo
.
ENABLE
Micro
PDF 417
DISABLE
ww w.tec-it.com
.
Demo
.
ENABLE
QR Code
DISABLE
Demo
.
Demo
.
ENABLE
Data Matrix
DISABLE
Demo
.
Demo
.
ENABLE
MaxiCOde
DISABLE
ww w.tec-it.com
.
Demo
.
ENABLE
Aztec Code
DISABLE
Demo
.
Demo
.
ENABLE
Chinese Sensible
(Han Xin) Code
DISABLE
Demo
.
Demo
.
Quick guide is subject to change without notice.
R_180808_01