RIOTEC iDC9270J User manual

1
Quick Guide
- iDC9270J
1
Connect to micro USB port of
Smartphone
2
3
*Before you use scanner, please switch to "C- Charge
mode" and charge inside battery for 3~4 hours first.
*Under “C- Charge mode”, you can raise/lower
soft-keyboard easily. (For HID profile only)
4
iDC9270J is with Li-Ion battery inside. When in charging,
please use the original USB power adaptor of Smartphone
(recommended). Through it, it charges both smartphone
& iDC9270J batteries at the same time.
When in low battery (Orange LED flashing), please charge
it immediately.
In case the power consumed out totally; the RTC (Real
Time Clock) will back to original setting 01012000.
Attention: Please don’t charge iDC9270J when in Operation
mode. Otherwise, the smartphone’s battery will charge back
to iDC9270J’s battery.
5
** When pressing Left button + Right button for 8~9 seconds,
iDC9270J will enter deep sleeping mode.
** Please press Left button + Right button + Touch trigger for
8~9 seconds to activate iDC9270J.
** The touch sensor area is around the central area.
Please check the above drawing for your reference.
LED Indicator Information
Orange LED ON
Full charged
Orange and Red LED Flashing
Charging
Orange LED Flashing
Low battery
Red LED ON
Off line / out of service
Green LED ON
Good read
Orange LED ON
Good read (Batch mode)
O=Operation mode
C=Charge mode
Left Button
Under BT HID Profile, press Left button to raise/lower
soft-Keyboard; press the left button for 4 seconds to
un-pair. Then, scanner can be connected with other
BT devices (Please check page #2, left column)
Touch Trigger Area
SCAN/ Power ON
Press 1 second to wake it
up from power saving
mode
Right Button
Power Saving button:
Press the button for 4 second
then enter power saving mode
Indicator
(LED)
Charge port
Suction Cup
PU Glue
(Can be used
repeatedly)
Micro USB
cable (OTG)
Exit Window
Li- Ion Battery inside
Indicator (LED)

2
How to Connect to Smartphone
1. Make sure your device has BT HID or SPP profile
2. Turn off Power-Saving mode on your smartphone first
3. Then, choose HID or SPP profile and scans the following 2 setting
codes before connecting to smartphone.
(a1 a2 or b1 b2)
If you don’t know what profile your device is, please try HID
profile first, then, SPP profile.
HID profile
SPP profile
a1
%H%I%D
b1
%S%P%P
a2
%B%R%C
b2
%B%R%C
4. Please complete the connection procedures as the right photos.
5. After the connection is completed, the RED light will be OFF.
6. Before using WordPad file or appropriate APP, please set
keyboard language of device to User’s language. Then, scan
the barcodes and the barcode data will show on the cursor side.
Soft-Keyboard setting code for Android / iOS
%A%N%R
For Android
%I%O%S
For iOS
*Under Android system, if you want to raise/lower soft-keyboard, please read
the above setting code first. Then, press left button (refer to drawing #5 on
page #1) to raise keyboard (LED is RED /Bluetooth is offline), press it again
to lower keyboard (LED is off/ Bluetooth is online)
*It will take 5~10 seconds to make BT online/offline.
*Please be noted that when BT is offline, scanning function is
stopped.
*Or, switch “C” to “O” to make BT online. (Drawing 3, page #1)
*Under iOS system, press Left button to raise/lower soft-Keyboard;
*Press the left button for 4 seconds to un-pair. Then, scanner can be
connected with other BT devices
1. click the “Settings”
2. click “General”
3. click “Bluetooth”
4. Turn it ON, and search the
Devices
5. Select “Rxxxxxx” to connect
6. When see the “Connected” means
the connection is OK.
(example: pairing with iPhone)
Reset Configuration to Defaults
(scan from A1 to A4 for HID profile or B1 to B3 for SPP profile)
HID profile
SPP profile
A1
DEFOVR
B1
DEFOVR
A2
SERIAL
B2
SERIAL
A3
RETURN1
B3
Demo
%D%F%T
A4
Demo
%D%F%T

3
There are two operating modes on the scanner
1.Data Transmission mode (Default)
Demo
%M%A%F
It is a necessary to scan “clean memory data" when
switching between these two modes.
Within Bluetooth radio
range
Beyond Bluetooth radio range
Data
read
Transmit data to PC/terminal
directly
Save data into scanner’s memory,
scanner will transmit data to PC/
terminal automatically when back to
Bluetooth radio range.
Enter Data Storage mode
LED
Green/ Orange LED flashes
followed by 3 beeps.
2.Data Storage mode (Batch Mode)
Demo
%M%A%N
It is a necessary to scan “clean memory data" when switching
between these two modes.
Data
read
Save data directly to scanner’s memory, It will transmit the data to PC/
terminal after you scan the Transmit memory data code. To delete
data please scan the Clean memory data code.
Enter Data Transmission mode
LED
Green/Orange LED flashes followed by 3 beeps.
Always Clean memory data before switching to Data Transmission
Mode. Otherwise Red/ Orange LED will flash with one long beep and
will not switch modes.
Under Data storage Mode
The data can be keep or delete by option after transmit
Demo
%M%D%K
Demo
%M%D%E
Keep the data
(Default)
Delete the data
Demo
%R%E%C
Transmit memory data
Green/Orange LED Flashes followed by 3 beeps
Demo
%E%R%A
Clean memory data
Green/Orange LED flashes followed by 3 beeps
The barcode data which is stored in the memory will be deleted.
Trigger Mode
Demo
%R%T%E
Trigger always
(Trigger available at any time)
Demo
%R%T%D
Trigger standard (Default)
(Trigger available, after data sent to the device)
Transmission Speed
Transmission speed is dependent on your device. In order not to lose data,
please choose the correct speed. Middle-speed is the Default.
Demo
%B%T%H
Demo
.
High-speed
Ultra Slow-speed
transmission
1transmission
Demo
.
Demo
.
Middle-speed
Ultra Slow-speed
transmission
2transmission
Demo
%B%T%L
Demo
.
Slow-speed
Ultra Slow-speed
transmission
(Default)
3transmission
Power-saving Mode
Demo
%P%D%T00
Power-saving mode OFF
Demo
%P%D%T05
Power-saving mode ON (Default):
Enter power-saving mode after 5-minute
inactivity. This function converses battery
power. When you press "SCAN/Power ON"
button, it will wake up and begin to scan.
Demo
%P%D%T10
Power-saving mode ON:
Enter power-saving mode after 10-minute
inactivity. This function converses battery
power. When you press "SCAN/Power ON"
button, it will wake up and begin to scan.
*When charging, the scanner will not enter power-saving mode
automatically.
RTC (Real-time clock),
please set the punctuation mark at the same time
You must scan the below configuration barcode to set the date & time
stamp on the scanner.
Demo
%D%I%N
Demo
%D%I%F
Date information:
ENABLE
Date information:
DISABLE (default)
Demo
%T%I%N
Demo
%T%I%F
Time information:
ENABLE
Time information:
DISABLE (default)
The format of Date setting
Demo
.
Date format 1: mm/dd/20yy (default)
For example: 01/23/2011
Demo
.
Date format 2: dd/mm/20yy
For example: 23/01/2011
Demo
.
Date format 3: 20yy/mm/dd
For example: 2011/01/23
The punctuation marks for the intervals among
barcode data, date, time
Demo
%T%S%C,
, comma (default) –FOR Android/iOS use
For example:
ABCD,01/23/2011,12:34:56
Demo
%T%S%C
Tab –FOR iOS use
For example:
ABCD 01/23/2011 12:34:56
Demo
%T%S%C;
; semicolon –FOR Android/iOS use
For example:
ABCD;01/23/2011;12:34:56

4
Date and Time setting
www.tec-it.com
%T%S%D
SET DATE
Scan the SET DATE barcode, then, scan the six
numeric digits in the format mm/dd/yy, from the
numeric barcode.
For example: “01/23/2011”, please input
012311
Demo
%T%S%T
SET TIME
Scan the SET TIME barcode, then, scan the six
numeric digits in the format hh:mm:ss from the
numeric barcode. Time format: 24hr clock
For example: “PM 3:25:30”, please input
“152530”
Keyboard Country (For HID profile only)
Demo
.
Scan the appropriate country code as below
to program the keyboard layout for your
country or language. As a general rule, the
following characters are supported, but need
special care for countries other than the
United States: @ | $ # { } [ ] = / ‘ \ < > ~
Follow the steps mentioned below to program.
1. Keyboard Country setting code.
2. “Select Country Code”
Read numeric barcode (according to country code).
Country/
Language
No.
Country/
Language
No.
Country/
Language
No.
U.S.
10
Netherlands
26
Switzerland
French
45
Latin
America
11
Hungary
27
Switzerland
German
46
Brazil
12
Italian
28
Sweden
47
Belgium
20
Icelandic
29
Turkey F
48
Bulgarian
Latin
21
Norway
30
Turkey Q
49
Denmark
22
Poland
41
Japan
71
Finland
23
Portugal
42
Korea
72
France
24
Russia
43
Thai
73
Germany
25
Spain
44
Vietnam
74
How to append a “prefix” or a “suffix” to the
barcode data
Demo
%C%P%S
Demo
%C%S%S
prefix
suffix
1. scan above configuration code for Prefix or Suffix
2. enter the required values (right, numeric barcode) for Prefix or Suffix
using the hex values for the desired HEX values from Prefix & Suffix
TABLE (below page)”
3. then, end by scanning Code X (below, right)
*The max. of special characters is 5.
*When you append 1~4 required values for Prefix or Suffix, it must end
with Code X.
*It doesn’t need Code X, if you append 5 values to barcode data.
How to delete Prefix or Suffix
1. scan above configuration code for Prefix or Suffix
2. enter the “0” “0” (above, left)
3. then end by scanning Code X (below, right)
Numeric barcode for settings
Demo
0
Demo
6
Demo
C
Demo
1
Demo
7
Demo
D
Demo
2
Demo
8
Demo
E
Demo
3
Demo
9
www.tec-it.com
F
Demo
4
Demo
A
Demo
5
Demo
B
Demo
X
Prefix & Suffix TABLE
HEX
HID
(SPP)
HEX
HID
(SPP)
HEX
HEX
HEX
HEX
01
CTRL A
(SOH)
19
CTRL Y
(EM)
20
SPACE
38
8
50
P
68
h
02
CTRL B
(STX)
1A
CTRL
Z(SUB)
21
!
39
9
51
Q
69
i
03
CTRL C
(ETX)
1B
ESC
(ESC)
22
"
3A
:
52
R
6A
j
04
CTRL D
(EOT)
1C
CTRL \
(FS)
23
#
3B
;
53
S
6B
k
05
CTRL E
(ENQ)
1D
CTRL ]
(GS)
24
$
3C
<
54
T
6C
l
06
CTRL F
(ACK)
1E
CTRL ^
(RS)
25
%
3D
=
55
U
6D
m
07
CTRL G
(BEL)
1F
CTRL _
(US)
26
&
3E
>
56
V
6E
n
08
Backspace
(BS)
27
'
3F
?
57
W
6F
o
09
Tab
(HT)
HEX
HID
Only
28
(
40
@
58
X
70
p
0A
CTRL J
(LF)
80
F1
29
)
41
A
59
Y
71
q
0B
CTRL K
(VT)
81
F2
2A
*
42
B
5A
Z
72
r
0C
CTRL L
(FF)
82
F3
2B
+
43
C
5B
[
73
s
0D
Enter
(CR)
83
F4
2C
,
44
D
5C
\
74
t
0E
CTRL N
(SO)
84
F5
2D
-
45
E
5D
]
75
u
0F
CTRL O
(SI)
85
F6
2E
.
46
F
5E
^
76
v
10
CTRL P
(DLE)
86
F7
2F
/
47
G
5F
_
77
w
11
CTRL Q
(DC1)
87
F8
30
0
48
H
60
`
78
x
12
CTRL R
(DC2)
88
F9
31
1
49
I
61
a
79
y
13
CTRL S
(DC3)
89
F10
32
2
4A
J
62
b
7A
z
14
CTRL T
(DC4)
8A
F11
33
3
4B
K
63
c
7B
{
15
CTRL U
(NAK)
8B
F12
34
4
4C
L
64
d
7C
|
16
CTRL V
(SYN)
35
5
4D
M
65
e
7D
}
17
CTRL W
(ETB)
36
6
4E
N
66
f
7E
~
18
CTRL X
(CAN)
37
7
4F
O
67
g

5
Barcode Configuration Method:
(Flow chart for setup procedure :)
1D Symbologies –1
ENABLE
CODABAR
DISABLE
CODBAR1
CODBAR0
ENABLE
CODE 39
DISABLE
CODE391
CODE390
ENABLE
Interleaved 25
DISABLE
ITF251
ITF250
ENABLE
Industrial 25
DISABLE
IDS251
IDS250
ENABLE
ISSN
DISABLE
ISSN1
ISSN0
ENABLE
GS1 DataBar
DISABLE
RSS141
RSS140
ENABLE
GS1 Databar
Limited
DISABLE
GS1LMT1
GS1LMT0
ENABLE
GS1 Databar
Expanded
DISABLE
GS1LMT0
GS1EPD0
1D Symbologies –2
ENABLE
Matrix 25
DISABLE
MAT251
MAT250
ENABLE
CODE 93
DISABLE
CODE931
CODE930
ENABLE
GS1-128
DISABLE
GS11281
GS11280
ENABLE
UPC-A
DISABLE
UPCA1
UPCA0
ENABLE
UPC-E
DISABLE
UPCE1
UPCE0
ENABLE
EAN 8
DISABLE
EAN81
EAN80
ENABLE
EAN 13
DISABLE
EAN131
EAN130
ENABLE
ISBN
DISABLE
ISBN1
ISBN0
2D Symbologies
ENABLE
PDF 417
DISABLE
PDF4171
PDF4170
ENABLE
QR Code
DISABLE
QRCODE1
QRCODE0
ENABLE
Micro QR Code
DISABLE
MQRCOD1
MQRCOD0
ENABLE
Data Matrix
DISABLE
DATAM1
DATAM0
ENABLE
Aztec Code
DISABLE
AZTEC1
AZTEC0
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw
R_180807_01