Ritelite Lpl601xldbzrc User manual

Location of Controls

1. 8 Super Bright LEDs

2. ON/OFF Switch with Selectable Dimmer

3. Folding Neck

4. Dual Adjustable Light Heads

5. Remote Control Signal Receiver

6. EZ-Mount Bracket

7. Built-In Bubble Level

8. Battery Compartment*

9. Remote Control

10. Remote Control Signal Transmitter

11. Battery Compartment*

12. ON/OFF Switch with Selectable Dimmer

13. EZ-Mount Bracket

*behind EZ-Mount Bracket

Getting Started: Remove plastic insulator tab from battery compartment.

EZ-Mount Bracket

1. First remove printed paper mounting template from back of unit.

2. Drill two (2) pilot holes in the location where you want to mount the picture light.

Place screws (included) in pre-drilled holes. Tighten slightly until secure, but do not tighten all the way.

Slide EZ-Mount Bracket keyhole slots over screw heads and into position.

3. Use the built-in bubble level to make sure the mounting bracket is level before securing it to the wall.

4. Once you conﬁrm that the bracket is level, tighten the screws to secure it to the wall.

Take care to not over tighten.

5. To hang the picture light on the mounting bracket, align the picture light with the mounting bracket and slide

the unit down. Light will lock into position.

6. To remove the picture light from the mounting bracket;

A) Hold the picture light by the base (not light head).

B) Slide the unit up.

C) Once the body releases from mounting bracket, pull the unit towards you.

Mounting the Remote Control Hook and Loop Tape (included):

1. Check the location of where you want to place the Remote. Make sure it is clean and that there is no debris or dust.

2. The two sides of the hoop and loop tape come pre-attached for ease of mounting. Remove the paper covering on one

sticky side of the tape.

NOTE: Hook and loop tape may be cut to desired size for easier removal.

3. Place the tape in the recessed area in the center on the back of the Mounting Bracket.

4. Remove the paper covering on the other sticky side of the tape.

5. Place the Mounting Bracket in the desired location. Press ﬁrmly and hold for ﬁve (5) seconds so that the tape adheres to

the surface.

CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or damage surface.

Screws (included):

You can secure the EZ-Mount Bracket to almost any surface using 2 screws. To do so, remove the Remote from the bracket by sliding it up and out of the bracket. Use the

printed paper mounting template for pilot hole positions.

1. Drill two (2) pilot holes in the location where you want to mount the Remote Control

making sure you are within 16 feet (5 meters) of the LED lighting system.

2. Place screws (included) in pre-drilled holes. Tighten slightly until secure, but do not tighten all the way. Slide the EZ-Mount Bracket keyhole slots over screw heads and

into position.

3. Tighten screws to secure the bracket to the wall. Take care to not over tighten.

4. Place the Remote Control in the mounting bracket.

Operating Directions

Light Positioning

Your wireless LED picture light ships ﬂat. To extend light head into proper position hold base in one hand and hold

light head at center with other hand (where neck attaches to light head). Rotate base backward until base and light

head are at farthest point from each other. Pivot each light head independently to desired angle.

NOTE: Each light head can only be turned 180° up or down

(Fig 1). To prevent damage to the unit, do NOT overturn the light heads. Doing so may damage the unit and will void the warranty.

YOU CAN OPERATE AND CONTROL THE WIRELESS PICTURE LIGHT TWO WAYS:

Manual Operation Using ON/OFF Switch On Light

1. Press once for full brightness.

2. Press and hold until the LEDs reach the desired brightness then release the button.

3. Press a third time to turn the light OFF.

LPL601XLDBZRC/LPL601XLGRC/LPL601XLBRC Owner’s Manual

Unit Back

REMOTE CONTROLLED

WIRELESS LED PICTURE LIGHT

MOUNTING

SURF A CE

UNIT

Picture Frame

Mounting Bracket

Unit Slides Down

Onto Mounting Bracket

Screw

Mounting Bracket

Keyhole Slots

UNIT BACK

Built-In

Bubble Level

Fig 1

LPL601XLDBZRC-LPL601XLGRC-LPL601XLBRC Manual.indd 2 6/20/11 3:10:48 PM

Remote Operation Using Wireless Remote Control

Where you mount the remote control in relation to the picture light will determine how is best to control the light using the remote control. The remote uses Infra

Red technology. This is the same type of technology used in most TV remote controls. As such, physically removing the remote from its mounting bracket and

pointing it at the picture light may be necessary. For best operation, use the remote control within 16 feet of the LED picture light.

1. Press the bottom of the switch once to turn the LED lights ON.

2. Press and hold the bottom of the switch until the desired level of brightness is reached then release the switch.

3. Press the bottom of the switch a third time to turn the LED lights OFF.

Positioning the Remote Control

For best operation, we recommend mounting the remote control with the “ ” graphic pointing upwards (Fig 1). Depending on

where you mount your picture light, you may need to physically remove the Remote Control from it’s bracket and point it directly at

the Remote Control Signal Receiver.

When doing so, the “Signal” graphic on Remote Control

should be pointed in the direction of the Power Module.

Inserting/Replacing the Batteries

If the LEDs appear to be dim this is an indication that your batteries need to be replaced.

1. To remove the picture light from the mounting bracket;

A) Hold the picture light by the base (not light head).

B) Slide the unit up.

C) Once the body releases from mounting bracket, pull the unit towards you.

2. Open the battery compartment cover.

3. Remove old batteries and replace with 3 new AA batteries.

4. Make sure to follow battery polarity guide when installing new batteries.

5. Replace battery compartment cover and remount the light.

Changing the Remote Control Batteries

If the Remote Control does not work to turn the LED lights ON, this may be an indication that the battery needs to be replaced.

Replacing the Batteries:

1. Remove the Remote from the EZ-Mount Bracket by pulling it up and out of the bracket.

2. Using a coin or similar object, remove battery compartment cover on the back of unit to open the battery compartment.

3. Remove the old battery (if replacing).

4. Insert new CR2032 battery. Be sure to match the battery polarity guide when installing new battery.

5. Replace the battery compartment cover.

Battery Precautions:

1. Use only the size and type of batteries speciﬁed.

2. Always purchase the correct size and grade of battery most suitable for the intended use.

3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device.

4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.

5. Replace all batteries of a set at the same time. Do not mix old and new batteries.

6. Clean the battery contacts and also those of the device prior to battery installation.

7. Do not dispose of batteries in ﬁre.

8. Remove batteries if consumed or if product is to be left unused for an extended period of time.

062011

Limited 1 Year Warranty

If you recently purchased the item the quickest option is to return the product to the retailer where the item was purchased. Return policies vary by retailer. If returning the item to the retailer is not possible,

please contact Customer Service at (800) 527-0195 or at [email protected]

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.