Eaton Sure-Lites XR6C-LED User manual

INS #
IB505020EN 049-276 SURE-LITES
Installation Instructions for the Sure-Lites XR6C-LED Emergency Light
WARNING
Risk of Fire/Electric Shock
If not qualified, consult an electrician.
WARNING
Risk of Electric Shock
Disconnect power at fuse or circuit breaker before
installing or servicing.
Important Safeguards
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING
THE FOLLOWING.
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Do not use outdoors.
3. Do not use in hazardous locations, or near gas or electric
heaters.
4. Do not let power supply cords touch hot surfaces.
5. Use caution when servicing batteries. Battery acid can
cause burns to skin and eyes. If acid is spilled on skin or in
eyes, flush acid with fresh water and contact a physician
immediately.
6. Do not use this equipment for other than the intended use.
7. Installation is to be performed only by qualified personnel.
8. Install in accordance with National Electric Code and local
regulatory agency requirements.
9. The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
10. Equipment should be mounted in locations and at heights
where it will not readily be subjected to tampering by
unauthorized personnel.
11. SAVE THESE INSTRUCTIONS
MAX MOUNTING HEIGHT: 27.6 ft.
INSTALLATION
1. De-energize the circuit at the junction box (J-box) where
the emergency light is to be installed.
2. Open the emergency light by inserting a screwdriver in the
two slots on either side of the unit, then tipping the cover
up off of the backplate (See Fig. 1).
3. To mount to a junction box - Knock out the appropriate
mounting pattern and the wire pass hole in the backplate
to fit the J-box being used.
4. To mount to conduit – Select either the top or side
mounted knockout on the housing, then attach the 1/2”
conduit hub to the housing.
5. Once the backplate is secured, the housing can be held in
place during installation using the EZ Hang feature. (see
Fig. 2)
6. Connect the incoming wires to the fixture’s power supply
wires using the wire nuts provided. Connect the white
wire to neutral. If using 120V, connect the black wire to the
hot lead. If using 277V, connect the orange wire to the hot
lead. Cap the unused lead (see Schematic).
7. Snap the housing onto the backplate.
8. Remove the EZ key battery disconnect.
9. Energize AC supply. The test button should illuminate, and
LED heads will illuminate briefly when the test button is
pushed.
10. Adjust the heads as needed.
11. If the fixture is to be powered down for an extended
period after initial installation, replace the EZ Key. This
will prevent the battery from discharging when AC power
is removed. However, it will also prevent the battery
from charging when AC power is restored, so it must be
removed once the unit is ready for regular operation.

Installation Instructions for the Sure-Lites XR6C Emergency Light
© 2016 Eaton
All Rights Reserved
Printed in USA
Impreso en los EE. UU.
Publication No. IB505020EN
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
Eaton es una marca comercial
registrada. Todas las marcas
comerciales son propiedad de sus
respectivos propietarios.
Warranties and Limitation of Liability
Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions.
OPERATION
Depress the test switch. The LED heads will remain lit and the
charge LED will extinguish. LED heads will illuminate as long
as the button is pushed. Release the test switch. The charge
LED will illuminate and the LED heads will turn off.
MAINTENANCE
Replace the batteries as needed according to ambient
conditions. However, we recommend that the equipment be
Figure 2
Slide hooks through slots
in housing for temporary
mount when wiring.
Figure 1
Insert screwdriver
in slots on side of
fixture to open.
SCHEMATIC
c
J1
LED/SW
N 120 277
RMT
-
LAMPS
BATT
+
CN4
U2
U1
SW1
R16
R15
R14
R13
R12
R11
R10
R9
R8
R7
R6
R5
R4
R3
R2
R1
Q5
Q4
Q3
Q2
Q1
MOV2
MOV1
LED1
JK5
JK4
JK3
JK2
JK1
F1
D9
D8
D7
D6
D5
D4
D3
D2
D1
CN3
CN2
CN1
C3
C2
C1
F2
R17
R18
+
BLACK -
120VAC
WHITE -
NEUTRAL
ORANGE
- 277VAC
BATTERY
LED
HEADS
CHARGER /
DRIVER PCB
Installation Instructions for the Sure-Lites XR6C-LED
Emergency Light.
tested regularly in accordance with local codes.
NOTE: Servicing of any parts should be performed by qualified
personnel. Only use replacement parts supplied by Eaton
Lighting.
CAUTION: This equipment is furnished with a sophisticated low
voltage battery dropout circuit to protect the battery from over
discharge after its useful output has been used. Allow 24 hours
recharge time after installation or power failure for 90 minute
testing.
TROUBLE SHOOTING GUIDE
If LED heads or charge indicator LED does not illuminate, check
the following:
1. Check AC supply – verify that unit has 24 hour AC supply.
2. Unit is shorted or battery is not connected.
3. Battery discharged. Permit unit to charge for 24 hours and
then re-test.
4. If following the above trouble shooting hints does not
solve your problem, contact your local Eaton Lighting
representative for assistance.