ritm RBR1-L User manual

Radio channel panic button
RBR1-L
868 MHz
Data sheet
Device ID

2
1. Overview
The radio channel panic button RBR1-L (hereinafter referred to as panic button)
is designed for generating an alarm event on button pressing and transmitting it to the
radio channel receiver RDK-L 868 MHz.
When the radio channel receiver RDK-L receives the alarm event, the state of the
appropriate receiver output changes.
2. Manufacturer
RITM Company
195248,
Energetikov avenue, building 30, block 8,
St Petersburg, Russia
Tel.: [phone]
www.ritm.ru/en [email protected]
3. Package content
The radio channel panic button RBR1-L 1 pc.
Battery CR2032 1 pc.
Fixing set 1
Data sheet 1 pc.
Package 1 pc.

3
4. Technical specifications
Parameter Value
Frequency range, MHz 868.7-869.2
Maximum receiver emitting power, mW 10
Alarm message delivery acknowledgement +
Maximum range of stable
communication, m, up to
Restrained urban conditions 300
Medium urban conditions 500
Open territory 2000
Line-of-sight range 3000
Single battery operation, number of button pressings, minimum 3001
Power supply voltage (battery CR2032), V 3
Average useful current, mA, up to
Standby mode 0.040
Event transmitting 40
Dimensions, mm 60×41×14
Weight (without battery), g, up to 60
Operating temperature range without battery, °С−30…+35
Operating temperature range with battery, °С−20… +35
1In case of transmitting up to 2 events per hour. Operating time directly depends on event
transmitting frequency as well as on temperature and signal reception quality. In case of sub-zero
temperatures the operating time is essentially decreased.

4
5. Unit designation
Unit
Designation
1
Small strap fixing.
2
Operation mode indicator (VD1).
3
Screw hole for enclosure fixing.
Panic button SA1.
Panic button SA2.
Panic button SA3.
XS1 Connector for battery CR2032 installing.
The command running if buttons SA1, SA2 and SA3 are pressed, is set in
the section “Outputs” of the radio channel receiver “RDK-
L” configuration
software.
6. Visual indication
Indicator color
State
Value
Yellow Blinks one time
The button is added to the radio system of
the radio channel receiver.
Flash for 2 seconds
The radio system is not found
Green Blinks one time
The transmitted alarm is received by the
radio channel receiver.
Red
Blinks up to 2 times2
Alarm transmitting
Blinks 2 times every
6 seconds
Battery is discharged.
2The panic button tries to transmit an alarm two successive times.
SA1
SA3
SA2
XS1
+
–
XS1
VD1
Enclosure
Front view
Enclosure
Rear view
Board
1
3
2
CR2032
+

5
7. Button designation
Button
Pressing
Operating mode
or or
At least 2 seconds Alarm transmitting.
+ At least 2 seconds
Mode for adding the radio channel receiver
“RDK-L” to the radio system.
8. Setting-up procedures
1. Open the enclosure.
2. Install the battery CR2032 into the connector XS1. Battery installation is shown on
the picture (see section 6).
3. Switch the radio channel receiver “RDK-L” intended to be used with the panic
button to the mode for adding devices. (see the receiver operating manual).
4. Switch the panic button to the mode for adding the receiver to radio system (see
section 8).
5. After adding the receiver to the radio system press any button (SA1, SA2 or SA3)
and ensure that the alarm is delivered to the receiver (see section 7).
For more details on successful adding of the panic button to the receiver radio system
and on alarm transmission, use the radio channel receiver RDK-L configuration software.
Detailed information about interoperation with the radio channel receiver RDK-L see in
the Receiver operating manual available on the official website www.ritm.ru/en.
9. Maintenance
On a regular basis but at least twice a year check safety of contacts and if necessary
dress bonding pads.
Change battery as and when necessary.
10. Safety measures
All works related to installation, configuration and maintenance of the panic button
should be performed in accordance with the Electrical installation code and by qualified
personnel.
The button is a safe device, the maximum power supply voltage level is 3 V.
11. Transportation and storage
The panic button should be transported in a package, in closed vehicles. Storage areas
should be free from current-conducting dust, acid and alkali fumes as well as active gases
able to corrode isolation.

6
12. Manufacturer warranty
The manufacturer warrants conformity of the button to the specification requirements
provided the transportation, storage, mounting and operation conditions are observed by
the consumer.
Warranty operating life — 12 months from the date of commissioning, but no more than
18 months from the date of manufacture.
Warranty shelf life — 6 moths from the date of manufacture.
The manufacturer reserves the right to make changes, not deteriorated of button
functionality without previous notice of consumers.
13. Reclamation details
In case of button failure or defect in the warranty period take a fault report stating the
date of button manufacture and commissioning, nature of a defect.
Send the faulty panic button with the fault report to the purchase address or to the
manufacturer.

7
Notes

8
Notes
Data sheet date 22.04.2019