RIUKOE SL-960 User manual

User manual
Please read the instructions carefully before use
This product manual contains important information about the safe installation and use of
this projector. Please read and follow these instructions carefully and keep this manual in
a safe place for future reference.
960 LEDs RGB 3in1 Strobe
SL-960

1
1. Safety Information................................................................................................. 2
2. Connecting to a DMX control device..................................................................... 3
3. Configuring the fixture for DMX control ............................................................... 4
4. Cleaning................................................................................................................ 5
5.DMX Channel........................................................................................................ 5
6. Control menu ........................................................................................................ 7
7. Specification ......................................................................................................... 8
TABLE OF CONTENTS

2
STATEMENT
Thank you for choosing RIUKOE. The product has well capability and intact
packing when leave factory. All of the user should comply with warning item
and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem
owing to ignore the manual.
1. Safety Informations
Review the following safety precautions carefully before installing or operating
the fixture. This fixture must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation of the
fixture and the hazards involved.
Preventing electric shock
⚫Always power off/unplug the fixture before removing any covers.
⚫Ensure that the power is turned off when connecting the fixture to the AC
mains supply.
⚫Ensure that the fixture is electrically connected to earth (ground).
⚫Do not apply power if the fixture is in any way damaged.
⚫Do not immerse the fixture in water or liquid.
Preventing burns and fire
WARNING! Risk of electric shock.
WARNING! Read the safety precautions in this section before
unpacking, installing, powering or operating this product.

3
⚫Install in a location that prevents accidental contact with the fixture.
⚫Install only in a well-ventilated space.
⚫Install only in accordance with applicable building codes.
⚫Do not paint, cover or modify the fixture.
⚫Keep all flammable materials away from the fixture.
⚫Allow the fixture to cool for 15 minutes after operation, before touching it.
⚫CAUTION: Exterior surface temperature after 5 min. operation = 45 °C
(113 °F). Steady state = 60 °C (140 °F).
Avoid personal injury
⚫Do not look directly at the light source from close range.
⚫Take precautions to prevent injury due to falls when working at height.
⚫For permanent installation, ensure that the fixture is securely fastened to a
load-bearing surface with suitable corrosion-resistant hardware.
⚫For temporary installation with clamps, ensure that the quarter-turn
fasteners are turned fully and secured with a suitable safety cable. The
cable must be approved for a safe working load (SWL) of 10 times the
weight of the fixture, and it must have a minimum gauge of 3 mm.
2. Connecting to a DMX control device
The fixture is controllable using a DMX control device and it can be connected
using a DMX cable.
WARNING! Ta ke measure to prevent personal injury.
WARNING! Ta ke measures to prevent burns and fire.

4
If using a cabled DMX system, connect the DMX in cable (with male 3-pin XLR
plug) and out cable (with female 3-pin XLR plug) to the DMX data link.
Terminate the DMX out cable of the last fixture in the data link. For outdoor
installations, use only IP-rated XLR connectors suitable for outdoor use.
The DMX512 is widely used in intelligent lighting control,with a DMX 512
controller.connect several lights together,dmx in and dmx out, 3 pin XLR
connectors: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
3. Configuring the fixture for DMX control
About DMX
The fixture can be controlled using signals sent by a DMX controller on a
number of channels (which varies depending on the DMX mode that has been
set).
The first channel used to receive data from a DMX control device is known as
the DMX start address. Each fixture must have a DMX start address set. For
example, if a fixture has a DMX address of 10 and it is in 4-channel DMX mode,
then it uses channels 10, 11,12 and 13. The following fixture in the DMX chain

5
could then be set to a DMX address of 14. If two or more DMX fixtures of the
same type have the same DMX address, then they will mimic each other’s
behavior. Incorrect settings will result in unpredictable responses to the lighting
controller.
4. Cleaning
To maintain optimal performance, regular cleaning is essential. Cleaning
schedules will vary depending on the operating environment, and the
installation should therefore be checked at frequent intervals within the first
few weeks of operation to see whether cleaning is necessary. This procedure
will allow you to assess cleaning requirements in your par- ticular situation.
Clean the fixture using a soft cloth dampened with a solution of water and a
mild detergent. Do not use products that contain solvents, abrasives or caustic
agents for cleaning, as they can cause damage to both hardware, cables and
connectors.
5.DMX Channel
5.1 Built-in Effect
Built-In Effect Channels
Effect Speed
0-10 : None
0-255 : Slow-Fast
11-200 : Each 3 Values with 1 Auto Effect;(Effect
1- Effect 56)
200-255 : Each 15 Values with 1 Sound Control ;
(Sound Control 1- Sound Control 4)
5.2
Strobe Channel Details
Static Color Channel Details
0-10 : None;
0-10 : Auto color change when running

6
11-255 : Slow- Fast ;(1HZ-20HZ)
effect;
11-255 : Each 36 Values with 1 color (Color
1-7);
5.3 Channels Mode
CHs
7CH
10CH
12CH
24CH
CH1
Dimmer
Dimmer
Red 1
Red 1
CH2
Strobe
Strobe
Green 1
Green 1
CH3
Red
Red 1
Blue 1
Blue 1
CH4
Green
Green 1
Red 2
Red 2
CH5
Blue
Blue 1
Green 2
Green 2
CH6
Built-In Effect
Red 2
Blue 2
Blue 2
CH7
Effect Speed
Green 2
Red 3
Red 3
CH8
Blue 2
Green 3
Green 3
CH9
Built-In Effect
Blue 3
Blue 3
CH10
Effect Speed
Red 4
Red 4
CH11
Green 4
Green 4
CH12
Blue 4
Blue 4
CH13
Red 5
CH14
Green 5
CH15
Blue 5
CH16
Red 6
CH17
Green 6
CH18
Blue 6
CH19
Red 7
CH20
Green 7
CH21
Blue 7
CH22
Red 8
CH23
Green 8

7
CH24
Blue 8
6. Control menu
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions,
ENTER To confirm the selected functions
Set DMX Address Code
1. Press "Menu" to "Set DMX Address",and press "ENTER" keys to enter into
2. Show "Set DMX Address DMX Address:001",Press the "UP and DOWN"
keys to amended
3Press "ENTER" keys to save and Exit,Press the "MENU" Keys does not
save and Exit
Display Function Table
A001
DMX Addr
A001--A512
CHND
CH Mode
7CH/10CH/12CH/24CH
FAIL
DMX Hold
HOLD: DMX hold on when signal off
BLND: DMX black out when signal off
CL01--CL07
Macro Color
7 Macro Colors（ST01--ST16: Strobe Slow to
Fast）

8
E000--E100
Effect Mode
55 Auto Effects（SP01-- SP16: Auto Speed
Slow to Fast）
E000：Full Auto Effects
Long press ENTER to confirm color
SOU0-SOU3
Sound Control
SOU0:Sound Control Effect
SOU1: Sound control change color
SOU2:Sound control DB1
SOU3:Sound control DB2
（SE1—99: Sound sensitivity slow - high）
MANU
Manual Mode
d000--d255：Total dimmer
r000-- r255：Red dimmer
g000--g255: Green dimmer
b000--b255: Blue dimmer
s000-- s25: Strobe from slow to fast
TEST
Test mode
Test whether all lamp beads are normal
LED
Display On/Off
ON: The display screen is always on
OFF: Turn off the display after 60s of no
operation
VER
Software Version
1.0
7. Specification
Light Source:
LED: 960pcs of 5050 SMD LED
Voltage: AC100V~240V, 50/60Hz
Power consumption: 250W
Control:
Power sockets: in/out

9
XLR sockets:3-pin XLR IN/OUT
Display: LED display
Electronic dimming:0-100% 12bit linear dimming
Strobe:1-20 times/second strobe
Control model:DMX512 and Master/slav,Sound active
DMX Channels: 7CH/10CH/12Ch/24CH
Dimension: 500 x 275 x140 mm
Weight:7.5 kg

10
Add: No.619 Building C Jiahua Square Yingbin Avenue Guangzhou China
[phone]
[e-mail]
www.riukoe.com
Facebook
YouTube