Rivers Edge Fast Stick RE711 User manual

TREESTANDS
HuntRiversEdge.com
CLIMBING AID INSTRUCTIONS
Fast
StickTM
Model
raw
Certified to
TMA Standards
by Independent
Test Lab
Parts Online
HuntRiversEdge.com
FAST STICK
Model RE711 (3 pack)
Model RE715 (single pack)
OMRE71509
Rev. 12/09/08
2009 Rivers Edge Treestands, Inc.
All Rights Reserved.

r!'

1/4' washer
tree hugger
weldment
1/4-20 x 3' bolt
HuntRiversEdge.com
Fast Sticks
RIVERS EDGE
TREESTANDS
Rivers Edge Treestands are engineered with you the hunter in mind.
We appreciate your purchase of one of our world class climbing aids.
Follow these few simple instructions and your climbing aid will pro-
vide you many years of trouble-free pleasure. Instructions should be
kept in a safe place and reviewed at least annually.
If for any reason you have a problem with your product, DO NOT
return to the retailer, contact the Rivers Edge customer service
department at 800-450-EDGE (3343) for assistance.
ASSEMBLY INSTRUCTIONS
Tools needed — two 7/16" wrenches
IMPORTANT ASSEMBLY TIP- DO NOT TIGHTEN NUT & BOLT
COMBINATIONS COMPLETELY UNTIL ALL PARTS ARE AS-
SEMBLED TOGETHER! FINGER TIGHTEN ONLY PLUS ONE TURN
OF A WRENCH ONLY! THIS WILL TEMPORARILY HOLD THE
LOCK NUT ON THE BOLT WHILE HELPING ALIGNMENT OF ALL
PARTS! AFTER ALL PARTS ARE ASSEMBLED TOGETHER, ALL
NUT & BOLT COMBINATIONS MUST BE COMPLETELY TIGHT-
ENED!
Attach (2) tree huggers (5512) to each fast stick weldment (48161) using
(2) provided 1/4-20 x 3" bolts, (2) locknuts and (2) 1/4" washers. SEE
FIGURE 1.TIGHTEN ALL NUT AND BOLT ASSEMBLIES COMPLETELY!
REPEAT FOR EACH ADDITIONAL FAST STICK SECTION.
NOTE: Head of bolts should be on the front side of step and locknuts
should be on back side of tree hugger.
Attach the provided anti-slip tape (48104) to the top side of each step.The
step must be clean and at room temperature to assure proper adhesion.
a. Using (1) of the provided cam strap assemblies (48302), insert the loop
end of the short strap through slot of strap attachment bracket located on
to the vertical post of Fast Stick weldment. You may choose either slot,
depending on left or right hand preference.
Take the entire cam strap assembly and feed it through the loop and
pull tight forming a cinch knot. This permanently attaches the strap to the
Fast Stick section. SEE FIGURE 2.
Repeat steps 3a and 3b to attach remaining strap assemblies to
remaining Fast Stick sections.
locknut
FIGURE 1
A
WARNING
YOU MUST PURCHASE AND ALWAYS USE A FULL BODY
HARNESS (FALL ARREST SYSTEM) WITH A CLIMBING
BELTTHAT MEETS TMA STANDARDS WHILE USING THIS
PRODUCT. SINGLE SAFETY FILETS AND CHEST HAR-
NESSES ARE NO LONGER ALLOWED AND SHOULD
NEVER BE USED. 
I
,
IF YOU ARE NOT WEARING A !
FULL BODY HARNESS
WITH A CLIMBING BELT THAT IS PROPERLY ATTACHED
TO THE TREE THAT IS PROTECTING YOU FROM A FALL,
DO NOT LEAVE THE GROUND. 1 .
READ, UNDERSTAND AND FOLLOW ALL ASSEMBLY,
INSPECTION, MAINTENANCE, a,
USE INSTRUCTIONS
PROVIDED BEFORE EACH USE. FAILURE TO FOLLOW
ALL WARNINGS AND INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH.I
I
ALL ASSEMBLY MUST BE DONE IN THIS ORDER AT
GROUND LEVEL BEFORE SETUPAND USE.
DO NOT CRUSH TUBING WHEN TIGHTENING BOLT AS-
SEMBLIES!

IDENTIFY AND FAMILIARIZE YOURSELF
WITH ALL PARTS BEFORE YOU 'START.
I
HANG-ON CLIMBING AIDS MUST BE PLACED ON THE
TREE AT A HEIGHT ABOVE THEIPLATFORM WHERE THE
USER CAN MAINTAIN A HANDHOLD OF THE UNIT AND
STEP DOWNWARDS ONTO THE TREESTAND. NEVER
STEP UP FROM A CLIMBING DEVICE TO GET INTO YOUR
STAND. 
.
WHEN USING A CLIMBING/LINEMAN'S BELTTO ASCEND
THE TREE,THE FULL BODY HARNESS TETHER SHOULD
BE ATTACHED TO THE TREE BEFORE STEPPING DOWN
ONTO THE TREESTAND.
SECTIONAL LADDERS AND STEPS SHOULD BE SPACED
ON THE TREE TO INSURE EACH STEP IS NO MORETHAN
18-INCHES APART.
CHECK EVERY STICK LADDERISECTION CONNECTION
EVERY TIME YOU USE THE STICK LADDER BEFORE YOU
LEAVE THE GROUND. IF STICK LADDER SECTIONS ARE
SEPARATING, DO NOT USE THE STICK LADDER.
I
,.....'"  —
.6,, 
..
I  !.
—..• 
'  .....
...
FIGURE 2 
I
Page 2
800-450-EDGE (3343)
•
HuntRiversEdge.com

HuntRiversEdge.com
Fast Sticks
RIVERSEDGE
TR
E
A
WARNING
FAILURE TO USE OR IMPROPER USE OF A FULL BODY
HARNESS (FALL ARREST SYSTEM) WITH A CLIMBING
BELT THAT MEETS TMA STANDARDS MAY RESULT IN
SERIOUS INJURY OR DEATH! READ, UNDERSTAND AND
FOLLOW ALL INSTRUCTIONS. IF ANY INSTRUCTIONS
ARE NOT UNDERSTOOD OR IFYOU HAVE A PARTS ISSUE
CALL 800-450-EDGE (3343) BEFORE USING.
DO NOT EXCEED THE TOTAL FIELD RATING- 300 LBS.
DOUBLE CHECK ASSEMBLY STEPS TO BE CERTAIN YOU
HAVE CORRECTLY ASSEMBLED THIS PRODUCT.
' STUDY YOUR NEW CLIMBING AID TO BECOME FAMILIAR
WITH ALL OF ITS FEATURES AND DESIGN. AT GROUND
LEVEL, FOLLOWING PROVIDED USE INSTRUCTIONS,
PRACTICE ATTACHING CLIMBING AID TO TREE AND RE-
MOVING FROM TREE BEFORE ATTACHING OVERHEAD.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PROPERLY USE A FULL BODY HARNESS (FALL ARREST
SYSTEM) WITH A CLIMBING BELT THAT MEETS TMA
STANDARDS AT ALL TIMES INCLUDING ASCENDING TO
AND DESCENDING FROM A TREESTAND.
MAINTENANCE TASKS TO BE DONE BEFORE EACH & EV-
ERY USE. REPLACE ANY QUESTIONABLE COMPONENTS
IMMEDIATELY WITH RIVERS EDGE ORIGINAL PARTS.
A FULL BODY HARNESS WITH LINEMAN'S/CLIMBING
BELT MUST BE WORN AT ALL TIMES WHILE USING THIS
PRODUCT. IFYOU ARE NOTWEARING A FULL BODY HAR-
NESS WITH A CLIMBING BELT THAT IS PROPERLY AT-
TACHED TO THE TREE THAT IS PROTECTING YOU FROM
A FALL, DO NOT LEAVE THE GROUND.
A FULL BODY HARNESS WITH LINEMAN'S/CLIMBING
BELT MUST BE WORN AT ALL TIMES WHILE INSTALLING
OR REMOVING ANY HANG-ON CLIMBING AIDS.
NEVER ATTACH CLIMBING AIDTO A DEAD, ODD-SHAPED,
LEANING, DISEASED, LOOSE-BARKED TREE OR UTILITY
POLES.
SETUP AND USE INSTRUCTIONS
A
WARNING
ALWAYS ATTACH THE CAM STRAP ASSEMBLY SO THE
SPRING LOADED CAM LEVER OF THE STRAP IS FACING
AWAY FROM THE TREE. NEVER TOUCH THE CAM LEVER
WHILE PUTTING WEIGHT ON THE STICK AND/OR CLIMB-
ING THE STICK AS THIS COULD POTENTIALLY RELEASE
THE STRAP AND REMOVE THAT SECTION FROM THE
TREE.
NEVER HOLD ONTO ANY SECTION OR PULL ON ANY
SECTION THAT IS NOT SECURELY ATTACHED TO THE
TREE WITH THE PROVIDED STRAP AND BUCKLE.
BE CERTAIN TO ALWAYS LEAN FORWARD, TOWARD THE
TREE WHEN ASCENDING OR DESCENDING CLIMBING
AID.
ALWAYS HAVE THREE POINTS OF CONTACT WHILE
CLIMBING STICK.
WHEN HUNTING FROM A TREESTAND, FALLS CAN OC-
CUR ANYTIME AFTER LEAVING THE GROUND CAUSING
INJURY OR DEATH.
NEVER JUMP OR BOUNCE ON A CLIMBING AID TO SEAT
IT TO THE TREE.
PERFORM THESE TASKS BEFORE EACH AND EVERY
USE (REPLACE ANY QUESTIONABLE COMPONENTS
IMMEDIATELY WITH RIVERS EDGE ORIGINAL REPLACE-
MENT PARTS). DO NOT LEAVE YOUR STAND OUTDOORS
- REMOVE AFTER EACH USE AND STORE INDOORS!
REPLACE ANY AND ALL TREESTAND STRAPS EVERY
TWO YEARS OR WHEN ANY SIGNS OF DAMAGE OR
WEAR EXIST BEFORE.
NEVER USE ANY PRODUCT THAT HAS NOT BEEN MAIN-
TAINED OR INSPECTED PROPERLY - YOUR LIFE DE-
PENDS ON IT!
Standing on ground, with (1) Fast Stick section against tree, take the snap
hook end of strap and wrap it around the tree. Connect hook to opposite
slot of attachment bracket by snapping into slot. Pull the tail of cam strap
tight so that the section is snugly secured to the tree.
SEE FIGURE 3.
Be certain all (4) contact points of tree huggers, (2) on each hugger; are
contacting tree.
NOTE: Be sure you wrap the strap correctly so there are no twists
in the strap and cam lever of buckle is facing away from the tree.
Take the section and pull down on it so it feels stable and is settled into
using position before stepping on it. Check again to be certain all (4)
contact points of tree huggers are contacting tree. Redo as neccessary
to accomplish this.
Climb the Fast Stick section only far enough to attach the second section
to the tree. Repeat steps 1 & 2 for proper attachment of all remaining Fast
Stick sections.
Reverse setup and use instructions to remove Fast Stick sections from
the tree.
FIGURE 3
11•111.
•
Parts Online
800-450-EDGE (3343)
Page 3
HuntRiversEdge.com

HuntRiversEdge.corn
RIVERS EDGE
Fast Sticks
TREESTANDS
ALWAYS...
Be physically fit, mentally alert, and well rested before using this product.
Read, understand and follow all warnings and instructions before use, save for
future reference.
Use a Full Body Harness (Fall Arrest System) with a climbing belt that meets TMA
standards at all times including ascending to and descending from a treestand,
Be fully aware of foot placement.
Inspect for missing parts, all hardware condition, and damage before every
application, replace if necessary.
Remove after every use, store product indoors.
Use only Rivers Edge original replacement parts.
Lean forward, toward tree, when ascending or descending climbing aid.
 .
Lubricate all slide together points with powder raphite to prevent binding, wear,
rust & noise.
Avoid all electrical power lines.
Inform someone of the hunting location, where the treestand will be located and
the expected duration of the hunt.
Carry a signal device such as a mobile phone, radio, whistle, signal flare or
personal locator device (PLD) and it must be readily available at all times.
Inspect the climbing aic:Vireestand and all safety devices each time before use and
do not store outdoors when not in use.
NEVER...
Sleep in itreestand.
Exceed the total field rating of 300 lbs.
Attach to a dead, odd-shaped, leaning, diseased, loose-barked tree or utility pole.
Use on trees with a diameter smaller than 8 inches or larger than 20 inches.
Use a climbing aid/treestand during inclement weather such as rain, lightning,
windstorms or icy conditions and end your hunt and return to the ground if
inclement conditions arise.
Carry gun or bow when ascending or descending.
Alter the original design of your climbing aid.
Jump on or use in a careless manner.
Lean out over edge of device.
Use when intoxicated or using over-the-counter medication or ptescription drugs.
Use a climbing aid/treestand when feeling ill, nauseous or dizzy! or if you have a
prior medical condition that could cause a problem (i.e. heart condition, joints that
lock up, spinal fusions, etc.) or if you are not well rested.
Rely on a tree branch for support.
Use a damaged product, replace with new.
Loan your climbing aid to someone else.
Recommended for adult use only.
BE SURE TO RAISE
I
IAND LOWER YOUR WEAPON OR GEAR
WITH A HAUL LINE. GUN BARREL END OR ARROW TIPS MUST
BE POINTED DOWN -AWAY FROM YOU.
INSTRUCTIONS SHOULD BE KEPT IN A SAFE PLACE AND RE-
VIEWED AT LEAST ANNUALLY.
READ AND PERFORM ALL MAINTENANCE TASKS AS DE-
SCRIBED IN INSPECTION & MAINTENANCE.
READ, UNDERSTAND AND FOLLOW ALL ASSEMBLY, IN-
SPECTION, MAINTENANCE & USE INSTRUCTIONS PRO-
VIDED BEFORE EACH USE. FA LURE TO FOLLOW ALL
WARNINGS AND INSTRUCTIONS COULD RESULT IN SE-
RIOUS INJURY OR DEATH.
A
WARNING
Page 4
IMO
IMMEI
Parts Online
•
HuntRiversEdge.com
800-450-EDGE (3343)

A
WARNING
READ BEFORE USING...SAVE THESE INSTRUCTIONS.
PERFORM THESE TASKS BEFORE EACH .AND EVERY
, USE. (REPLACE ANY QUESTIONABLE COMPONENTS
IMMEDIATELY WITH RIVERS EDGE ORIGINAL REPLACE-
MENT PARTS.) DO NOT LEAVEYOUR STAND OUTDOORS
- REMOVE AFTER EACH USE AND STORE INDOORS!
REPLACE ANY AND ALL TBEESTAND STRAPS EVERY
TWO YEARS OR WHEN ANY SIGNS OF DAMAGE OR
WEAR EXIST BEFORE.
NEVER USE ANY PRODUCTTHAT HAS NOT BEEN MAIN-
TAINED OR INSPECTED PROPERLY- YOUR LIFE DE-
- PENDS ON IT!
INNS
WINS.
•
HuntRiversEdge.com
Fast Sticks
1iERS EDG E .
INSPECTION AND MAINTENANCE SCHEDULE
FOR ALL RIVERS EDGE PRODUCTS
Inspect all webbing, rope, cord, and strap assemblies for wear or damage.
Inspect cables and cable ends for damage or kinking.
Inspect all hardware and chain components for,damage.
Inspect for any structural damage to product. (Return to factory for repair or discard
product if any damage is found.)
Inspect all nut and bolt assemblies to be certain none are loose.
Inspect for any missing parts.
lubricate BD pivot and side together points kWh powder graphite to prokent noise, wear, and
rust.
Inspect entire product for any rust, corrosion, cracks, freezing, excessive heat, or rolling
damage that may effect the safety of your product. Discard any questionable product.
Inspect entire product for any structural damage - pay close attention toall weld locations.
(Return to factory for repair or discard product it any damage is found.)
Using correct wrenches inspect all nut & bolt assembly locations and snug up any that
may be loose. Be careful not to crush tubing when lightening!
Inspect and check operation of all cables, cable ends, cord, rope, webbing, and strap or
chain assemblies. Replace with factory new any item
Or assembly that shows signs of
wear, damage, kinking, or functions incorrectly.
Inspect seat. Replace any seat with factory new that shows signs of structural damage
or wear.
Inspect all hardware for wear or damage, also be sure you have no missing parts.
Never modify your stand in any way by maldng repairs, replacing parts, or altering
adding or attaching anything to it except if explicitly authorized in writing by the
manufacturer.
WARRANTY
Rivers Edge Treestands, Inc., offers a lifetime warranty to be free from defects in materials and workmanship.This warranty applies to the original owner with a
proof of purchase. All items attached to our stands (seat, strap, rope, wood, etc.) that are degradable are warranted for a period of one year. There is no warranty
on paint. This warranty applies to products that are not modified, abused or misused in a manner that deviates from the products intended usage. Rivers Edge
Treestands offers no other warranty expressed or implied nor Is to be held liable for any damage that may result from any defect in a treestand manufactured by
them. Warranty work must be sent directly to Rivers Edge Treestands and performed by them.
To obtain warranty service and/or replacement instructions,
you must have prior approval from Rivers Edge Treestands before shipping your package to us by calling our customer service department at 800-
450-EDGE (3343) or by writing to: Rivers EdgeTreestands, Inc., P.O. Box 755,1690 Elm Street, Cumberland, WI 54829 bra return material authorization.
number (RMAti).
All items must be shipped prepaid. Rivers Edge Treestands will at no charge, repair or replace, at their discretion, any detective stand which
falls under the conditions stated above. Rivers Edge Treestands retains the right to change models, specifications and price without notice.
This equipment has been manufactured under strict quality guidelines. As with any equipment of this type, full understanding of the instructions and Cause is
mandatory for the safety of its user. Rivers Edge Treestands, Inc., is not responsible for any damages or injuries sustained due to improper use or modification
of any of its products, or due
to any use which deviates from the products intended usage. The manufacturer also is not responsible for any Injuries sustained
due to failure to adhere to the instructions for use. My misunderstanding of its operation should be directed to manufacturer prior to its use.
Owner is responsible to check product field rating and must never exceed maximum weight rating stated.
Rivers Edge Treestands, Inc., is not responsible
for any malfunction due to normal wear and tear and/or damage caused by improper use, improper maintenance or accidents. This product if used safely as
intended, will give you years of trouble free service. We hope you will enjoy the quality of our products for years to come, and have a safe hunt.
 -
For replacement parts, phone 800-450-EDGE (3343) or go online to www.HuntRiversEdge.com
.
A
800-450-EDGE (3343)
Parts Online
.Page 5
HuntRieersEdge.com

Parts Online
800-450-EDGE (3343)
Page 6
•
HuntRiversEdge.com
HuntRiversEdge.com
Fast Sticks
RIVERSEDGE E
FAST STICKS PARTS

--- 8 RIVERS C
EDGE
CS TA N OS
HuntRiversEdge.com
Fast Sticks
15'
RAPID STICK PARTS-RE711
KEY # PART # DESCRIPTION
QTY.
1 48161 WELDMENT, STEEL FAST
STICK
3
2 48261B WASHER 1/4 BLK ZNC
6
3 48280B BOLT 1/4-20 X 3" HHCS BLK
ZNC
6
4 48752B NUT, FLANGED, TOP LOCK,
1/4-20
6
5
SS12
WELDMENT, TREE HUGGER,
BOLT-ON RAPID STICK
6
48302
CAM STRAP ASSEMBLY, FAST
STICK
3
48104 ANTI-SLIP TAPE 9
15' RAPID STICK PARTS-RE715,
KEY #
PART # DESCRIPTION
QTY.
1 48161 WELDMENT, STEEL FAST
STICK
1
2
48261B WASHER 1/4 BLK ZNC
2
3
4828013 BOLT 1/4-20 X 3" HHCS BLK
ZNC
2
4 487528 NUT, FLANGED, TOP LOCK,
1/4-20
2
5 SS12
WELDMENT, TREE HUGGER,
BOLT-ON RAPID STICK
2
48302
CAM STRAP ASSEMBLY, FAST
STICK
1
--
48104 ANTI-SLIP TAPE
3
BOLT IDENTIFICATION CHART
Not all bolt sizes shown are included with all treestands. Bolts
shown are for size reference only. Extra hardware may be
included in the parts bag.
1/4-20 x 1-1/4" grade 5 hex head bolt
1/4-20 x 1-1/2" grades hex head bolt
 1/4-20 x 1-3/4" grade 5 hex head bolt
1/4-20 x 2" grade 5 hex head bolt
 1/4-20 x 2-1/4" grades hex head bolt
1/4-20 x 2-1/2" grade 5 hex head bott
1/4-20 x 2-3/4" grade 5 hex head bolt
1/4-20 x 3" grade 5 hex head bolt
1/4-20 x 3-1/4 grade 5 hex head bolt
5/16-18 x 2-1/2" grade 5 hex head bolt
5/16-18 x 3-1/4" grade 5 hex head bolt
Parts Online
800-450-EDGE (3343)
Page 7
HuntRiversEdgesom

ACCESSORY CHART & REPLACEMENT PARTS
ITEM #
DESCRIPTION
MSRp*
RE750 Universal Treestand Canopy
Protect yourself from the elements. Has a strong
ratchet for attaching to trees along with a sturdy
steel construction. Exclusive Rivers Edge Fall
Camouflage. Universal design, will work on all
treestands
$59199
48302
Cam Strap rAssembly, Fast Stick
$7.99
48104
,
Anti-slip Tape
.60
Prices shown do not includeishipping & handling charges.
All prices are sub ect to change without notice, When ordering from manufacturer,
there is a $10.00 minimum order.
For replacement parts, phone [phone]-EDGE (3343) or
go online to www.HuntRiversEdge.com
.
RIVERS EDGE°
TREESTANDS
Rivers Edge Treestands, Inc.
1690 Elm Street; RO. Box 755
Cum l berland, Wisconsin 54829
800-450-E6GE (3343) Fax [phone]
E-mail: [email protected]
Parts Online
•
HuntRiversEdge.com
* All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact.