Riverside Furniture 28032 User manual

F H
G1 pc.
5
16-18 x 44mm
Allen Head Bolt
5
16"x 19 x 2mm
Flat Washer
2 pcs. 10 pcs. 10 pcs. J
E
5
16-18 x 35mm
Allen Head Bolt
8 pcs. I2 pcs.
Components and Hardware List
Riverside
FURNITURE
email: [email protected]
Page 1 of 2
Made in Viet Nam
A
Perspectives
Wall Desk
Assembly Instructions
Desk Top
1 pc. 1 pc. 1 pc.
BCD
Left Leg Right Leg Stretcher
1 pc.
To remove the drawer if it ever becomes necessary:
A. Pull the drawer fully open so the black latch is visible in
the inside channel of the guides.
B. Release the latches by simultaneously pushing left side
lever up and the right side down.
C. At the same time, pulling the drawer forward until the
slides release.
To reinstall the drawers, carefully align the channels of the
guide and push drawer back into cabinet. Open and close
drawer fully a couple times to verify proper operation.
28032 / 28132 / 28232
Half Moon Washer
5
16"x 12 x 2mm
Spring Washer
J
EGH
B
C
A
5mm Allen Wrench
J
FG
HI
Bottom view
Be sure to check all packing material carefully for small parts, which may have come loose inside the carton during
shipment.
Step 1: Remove the drawers from the Desk Top (A) and lay them aside. Place the Desk Top on its back edge on a
clean, soft surface.
Step 2: Attach the Stretcher (D) to the Legs (B,C) by using 44mm long Allen Head Bolt (F), Spring Washer (G), Flat
washer (H) and Half Moon Washer (I), tighten with the 5mm Allen Key (J) as shown.
Step 3: Attach the Legs at the two sides of the Desk Top (A) using the 35mm long Allen Head Bolts (E), Spring
Washers (G) and Flat Washers (H). Tighten with the 4mm Allen Key (J).
Step 4: Carefully set the Desk upright and reinstall the drawers.
This is not A Stand-Alone Unit - Must Be Purchased With 2
Leaning Bookcases (One Bolted/Attached On Each Side)

Components and Hardware List
Riverside
FURNITURE
email: [email protected]
Page 2 of 2
Made in Viet Nam
Perspectives
Wall Desk and Learning Bookcase
Assembly Instructions
A
Wall Desk
1 pc. BC8 pcs.
Screw
Step1:Place the Bookcase (B) alongside to the Wall Desk (A), make sure the
three units are properly aligned
Step2: Secure Wall Desk to 2 Bookcases using the 4 Mending Plates.
Secure by using Screw (C). Tighten with your Phillips Head Screwdriver,
as seen in the illustration below.
Bookcase
2 pcs.
There are levelers underneath the Desk and Bookcase which can be adjusted to compensate for uneven
flooring. If the furniture wobbles, determine which corner does not touch the floor correctly. With
two people follow these steps:
1. Carefully elevate the item slightly to provide access to the levelers attached to the bottom.
2. Turn the levelers until adequate contact will be made with the floor. Gently set down the piece and
check stability.
Repeat steps until furniture sits firmly on the floor.
28032 / 28132 / 28232
28038 / 28138 / 28238
D4 pcs.
Mending Plates
B
B
C,D
For product and personal safety, an
Anti-Tip Restraint kit has been
included with this cabinet which can
help to minimize the risk of the
cabinet accidentally tipping forward,
if used and properly installed.