Robe Robin ProMotion ADM User manual

1
Version 1.7

2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Fixture exterior view ...................................................................................................... 5
3. Installation....................................................................................................................... 6
3.1 Connection to the mains ............................................................................................ 6
3.2 Rigging the xture ...................................................................................................... 7
3.3 Positioning the Robin ProMotion ............................................................................... 8
3.4 Additional base covers installation ......................................................................... 10
3.5 Installing the wide-angle lens .................................................................................. 11
3.6 Installing the Automatic Distance Meter (ADM) ....................................................... 12
3.7 DMX-512 connection................................................................................................ 13
3.8 Ethernet connection ................................................................................................. 14
3.9. Wireless DMX operation ......................................................................................... 15
4. Control menu map........................................................................................................ 16
5. Control menu ............................................................................................................... 19
5.1 Fixture Address ........................................................................................................ 19
5.2 Fixture information .................................................................................................. 20
5.4 Manual Control......................................................................................................... 22
5.5 Stand- alone............................................................................................................. 23
5.6 Reset Functions ....................................................................................................... 23
5.7 User Media............................................................................................................... 23
5.8 Special functions ...................................................................................................... 25
6. Keystones ..................................................................................................................... 26
7. Using external HDMI input........................................................................................... 27
8. Ways of le transfer from/to the ProMotion............................................................... 27
9. NAS operation............................................................................................................... 31
10. Software update of the xture................................................................................... 32
11. RDM.............................................................................................................................. 33
12. Error and information messages .............................................................................. 34
13. Technical Specications............................................................................................ 35
14. Maintenance and cleaning......................................................................................... 38
14.1 Replacing a fuse .................................................................................................... 39
15. ChangeLog ................................................................................................................. 39
Robin ProMotion

3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR ROBIN ProMotion !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en-
sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
The Robin ProMotion was designed for indoor use and it is intended for
professional application only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the xture.
This xture should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the xture from AC power before cleaning, removing or installing the fuses, or any part.
The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords
as this can result in re or electric shock.
Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by
persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power
cord from time to time.
Refer servicing to qualied service personnel.
This xture falls under protection class I. Therefore this xture has to be connected to
a mains socket outlet with a protective earthing connection.
Do not connect this xture to a dimmer pack.
LED light emission. Risk of eye injury. Do not look into the beam at short distance from
the product. Do not view the light output with optical instruments or any device that
may concentrate the beam
If the xture has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched o󰀨 until
it has reached room temperature.
Do not shake the xture. Avoid brute force when installing or operating the xture.
This xture was designed for indoor use only, do not expose this unit to rain or use near water.
When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, moisture,
dust or entertainment smoke (haze)

4
Air vents and slots in the xture head and base are provided for ventilation to ensure reliable operation of the
device and to protect it from overheating.
Do not block the light output with any object when the xture is under operation.
The openings should never be covered with cloth or other materials, and never must be blocked.
This xture should not be placed in a built-in installation unless proper ventilation is provided.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.
Always use a secondary safety cable when mounting this xture.
Do not block the front objective with any object when the xture is under operation.
The xture becomes very hot during operation. Allow the xture to cool approximately 20 minutes prior to ma-
nipulate with it.
Operate the xture only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the xture. Most damages are the result of unprofessional operation!
Please use the original packaging if the xture is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
If this device will be operated in any way di󰀨erent to the one described in this manual, the product may su󰀨er
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-cir-
cuit, burns, electric shock, crash etc.
Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the stand-
ard EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and
entertainment lighting control apparatus for professional use. Part 2: Immunity.
The product (covers and cables) must not be exposed to a high frequency electromagnetic eld higher than 3V/m
The installation company should check levels of possible interferences above the tested levels E1,E2,E3 given
by this standard (e.g. transmitters in surrounding area) before installing the equipment.
Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia
equipment – Emission Requirements according to class B.
To avoid damage of the internal optical system of the xture, never let the sunlight or
other xture lights directly to the front lens , even when the xture is not working !
Warning for the ProMotion ADM (ADM = Automatic Distance Meter) only:
LASER DEVICE CLASS 1

5
2. Fixture exterior view
7 - Ethernet OUT (RJ45)
8 - Ethernet IN (RJ45)
9 - 2x USB input
10 - HDMI input
11 - DMX OUT (5-pin XLR)
12 - DMX IN (5-pin XLR)
13 - Power OUT (PowerCon True 1)
14 - Power IN (PowerCon True 1)
1 - Moving head
2 - Arm
3 - Base
4 - Display
5 - Pan lock
6 - Tilt lock
The head has to be locked for transportation - the pan lock (5) and the tilt lock (6) have to be in locked positions.
To unlock the head, move these latches to unlock positions before operating the xture.
Note: the Robin Promotion ADM is equipped with an
automatic distance meter which enables autofocus of
the xture.

6
3. Installation
Fixtures must be installed by a qualied electrician in accordance with all
national and local electrical and construction codes and regulations.
3.1 Connection to the mains
For protection from electric shock, the xture must be earthed!
The Robin ProMotion is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
Install a suitable plug on the power cord (if it is needed), note that the cores in the power cord are coloured
according to the following table. The earth has to be connected!
If you have any doubts about proper installation, consult a qualied electrician.
Core (EU) Core (US) Connection Plug Terminal Marking
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
This device falls under class one and must be earthed (grounded)!
Design of the Robin ProMotion allows to connect several xtures to AC mains power in one interconnected
daisy chain using power input and output connectors. Needed daisy chain cords are stated in the chapter
“Technical specications “
The max. number of connected xtures depends on the AC mains power voltage and xture version:
CE cETLus
24 xtures at power supply= 230V 14 xtures at power supply= 230V
22 xtures at power supply= 208V 13 xtures at power supply= 208V
12 xtures at power supply= 120V 7 xtures at power supply= 120V
Actual numbers of xtures may di󰀨er from values stated above as you have to take into account the length of
supply cables, circuit breaker etc. at projecting of the xtures installation Do not overload the supply line and
the connecting leads.
Do not overload the supply line and the connecting leads.
Wiring and connection work must be carried out by qualied sta󰀨!

7
3.2 Rigging the xture
A structure intended for installation of the xture (s) must safely hold weight of the xture(s) placed on it. The
structure has to be certicated to the purpose.
The xture (xtures) must be installed in accordance with national and local electrical and construction codes
and regulation.
For overhead installation, the xture must be always secured with a safety wire
When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
Allow the xture to cool for ten minutes before handling.
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working
load limits, installation material being used, and periodic safety inspection of all installation materials and the
projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional
companies.
CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the xture!
The xture has to be installed out of the reach of public.
The xture must never be xed swinging freely in the room.
When installing the device, make sure there is no highly inammable
material (decoration articles, etc.) in a distance of min. 0.5 m.
CAUTION!
Use an appropriate clamp to rig the xture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is xed properly! Ensure that the
structure (truss) to which you are attaching the xtures is secure.
The xture can be placed directly on the stage oor or rigged on a truss without altering its operation characte-
ristics .
For securing the xture a truss install a safety wire that can hold at least 10 times the weight of the xture. Use
only the safety wire with snap hooks with screw lock gates. Fasten the safety cable in the attachment point
and around the truss as shown on the picture.
.

8
Rigging via two omega holders:
1-Clamp
2-Omega holders with quarter-turn loks
3-Truss
4- Safety wire
5-Attachment point for safety wire
When installing xtures side-by-side, avoid illuminating one xture with
another!
3.3 Positioning the Robin ProMotion
The Robin ProMotion is designed to be installed in one of four possible installation locations:
1. Front Table - the xture is placed near the oor in front of the screen.
2. Front Ceiling - the xture is suspended upside-down from the ceiling (truss) in front of the screen.
Set Ceiling Projection at On in the menu Personality ("Personality--->"LED Engine" --->"Ceiling Projection"---
>"On").
3. Rear Table - the xture is placed near the oor behind the screen. Set Rear Projection at On in the menu
Personality ("Personality--->"LED Engine" --->"Rear Projection "--->"On")
Note that a special rear projection screen is required.
4. Rear Ceiling - the xture is suspended upside-down from the ceiling (truss) behind the screen.
Set Rear Projection in the menu Personality ("Personality--->"LED Engine" --->"Ceiling Projection"--->"On") and
Ceiling Projection at On ("Personality--->"LED Engine" --->"Rear Projection"--->"On")
Note that a special rear projection screen is required.
When determining the position of the xture and projection screen, you will need to account for the projected
image size, which is directly proportional to the projection distance.

9
Note: There is a tolerance among these numbers due to optical component variations. We recommend that if
you intend to permanently install the Robin ProMotion, you should physically test the projection size and dis-
tance using the actual xture before permanent installation.
There is a chart of throw distance ratio of 3.5 : 1 to assist you in determining the ideal location for your
xture.

10
3.4 Additional base covers installation
The additional base covers cover connectors and the display of the xture´s base.
Disconnect the xture from mains before base covers installing.
To install the base covers:
1. Remove the display cover (1) by loosening the two quarter-turn locks (2) on the cover.
2. Fasten the additional cover (3) on the base by means of the two quarter-turn locks (4) instead of the display
cover (1).
3. Fasten the additional cover (5) (this cover is open from its bottom side) on the rear side of the base by means
of the two quarter-turn locks (6).
.

11
3.5 Installing the wide-angle lens
Disconnect the xture from mains before the wide-angle module installing.
To install the wide-angle lens:
1. Remove both covers (1) by loosening the four quarter-turn locks (2) on each cover.
2. Remove the front part (3) of the head by unscrewing the four screws M4x8 (4) and disconnecting cables.
3. Screw the module of Wide-angle lens (5) to the tube (11) by means of the three screws M3x10 (6) with nuts (7).
4. Unscrew the screw (8) and screw the screw M3x25 (10) with spacer (9) instead of the screw (8).
5. Place back the front part (3) of the head and screw it by means of the four screws M4x8 (4) and connect cables.
6. Place back both covers (1) and secure them by means of the four quarter-turn locks (2) on each cover.

12
3.6 Installing the Automatic Distance Meter (ADM)
Disconnect the xture from mains before installing ADM.
To install the ADM
1. Remove both covers (1) by loosening the four quarter-turn locks (2) on each cover.
2. Remove the front part (3) of the head by unscrewing the four screws M4x8 (4) and disconnecting cables
from the control PCB (11)
3. Remove the grey box module (5) of the head by unscrewing the four screws M4x8 (6).
4. Remove the black glass (7) by unscrewing its glass holder with four screws 3x8 (8).
5. Place a new glass with two apertures and secure it by means of the glass holder with four screws 3x8 (8).
6. Place the ADM (9) on the grey box module (5) and screw it by means of two screws M3x18 (10) and one
spacer (11) .
7. Screw the grey box module (5) back to the front part (3) of the head by means of the four screws M4x8 (6).
8. Screw the front part (3) of the head by means of the four screws M4x8 (4) and connect disconnected cables.
The Automatic Distance Meter (ADM) allows you to keep the image on the screen (wall, ceiling) permanently
focused during Promotion´s head movement.
For correct function of the ADM do not use a fog in the room where the Promotion is operating and do
not block the space between the screen and the Promotion (e.g. by walking persons).
The channel Focus (8) has to be set at 0 DMX.

13
3.7 DMX-512 connection
The xture is equipped with 5-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair
cable designed for RS-485 and 5-pin XLR plugs and connectors in order to connect the controller with the
xture or one xture with another.
DMX output DMX input
XLR sockets: XLR plug:
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with
the DMX input of the rst xture in the DMX chain.
Building a serial DMX chain:
Connect the DMX output of the rst xture in the DMX chain with the DMX input of the next xture. Always
connect one output with the input of the next xture until all xtures are connected. Up to 32 xtures can be
interconnected.
Caution: At the last xture, the DMX cable has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a 5-pin XLR plug and plug it in the DMX output of the last xture.
1- Shield
2 - Signal (-)
3 - Signal (+)
4 - Used for wireless DMX
5 - Used for wireless DMX
1- Shield
2 - Signal (-)
3 - Signal (+)
4 - Used for wireless DMX
5 - Used for wireless DMX

14
3.8 Ethernet connection
The xtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control soft-
ware running on your PC (or light console) has to support Art-Net protocol.
Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow
transfer of large amounts of DMX 512 data over a wide area using standard network technology.
IP address is the Internet protocol address.The IP uniquely identies any node (xture) on a network.
The Universe is a single DMX 512 frame of 512 channels.
The Robin ProMotion is equipped with 8-pin RJ- 45 socket for Ethernet input.Use a network cable category 5
(with four “twisted” wire pairs) and standard RJ-45 plugs in order to connect the xture to the network.
RJ-45 socket (front view): RJ-45 plug (front view):
1- TD+ 5- Not connected
2- TD- 6- RX-
3- RX+ 7- Not connected
4- Not connected 8- Not connected
Patch cables that connect xtures to the hubs or LAN sockets are wired 1:1,that is,pins with the same numbers
are connected together:
1-1 2-2 3-3 4-4 5-5 6-6 7-7 8-8
If only the xture and the computer are to be interconnected,no hubs or other active components are needed.A
cross-cable has to be used:
1-3 2-6 3-1 4-8 5-7 6-2 7-5 8-4
Connect the Ethernet inputs of all xtures with the Ethernet network.
The option “ArtNet" has to be selected from the menu “Mode” at the xture (DMXA 001-->Mode-->ArtNet).
Set IP address, NetMask and the Universe.
(DMX address=144) (DMX address=25) (DMX address=1)
IP addres=002.168.002.006 IP addres=002.168.002.003 IP addres=002.168.002.002
Universe=1 Universe=1 Universe=1
An advised PC setting: IP address: 002.xxx.xxx.xxx (Di󰀨erent from xture IP addresses)
NET mask: 255.0.0.0
The Robin ProMotion is equipped with an internal Ethernet switch which allows Ethernet IN-OUT connection.
If you use the IN-OUT line for the Ethernet connection without an external Ethernet switch, max. 8 xtures can
be connected in this case.

15
3.9. Wireless DMX operation
The wireless version of the xture is equipped with the Lumen Radio CRMX module and antenna for receiving
DMX signal. CRMX module operates on the 2.4 GHz band.
To switch the xture to the wireles DMX operation, select the option "Wireless DMX" from the menu "Receiving
Mode" (Fixture Address--> Receiving Mode--> Wireless DMX).
The option is also available in a DMX chart on the channel 6 (channel "Special functions", the range of 15-
19 DMX, the range of 10-14 DMX is designated for wired DMX). If DMX receiving option is changed by DMX
command, the change is permanently written into the xture memory.
DMX range of 10-19 DMX of the channel "Special functions" switches xture to the wired/wireless
operation and is active only during rst 10 seconds after switching the xture on.
After switching the xture on, the xture checks both modes of receiving DMX in the following order:
1. For the rst ve seconds, the xture receives DMX signal from the wired input. If the channel "Special func-
tions" is set at some DMX input option, the xture will receive DMX value according to this option. If DMX input
option is set to the wired input , this option is saved and checking procedure is nished. If DMX input option is
not set, the xture continues next 5 seconds in scanning wireless DMX signal-see point 2.
2. For the next 5 seconds the xture receives wireless DMX signal and again detects if the Special functions
channel is set at some DMX input option, if not, the xture will take option which is set in the xture menu
"Receiving mode".

16
4. Control menu map
Default settings=Bold print
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7
Fixture Address DMX Address 1-255
ArtNet Universe 0-255
sACN Universe 1-63999
Receiving Mode DMX
ArtNet
ACN
Wireless DMX
IP Address
IP Net Mask
Reset Address
Fixture Information Fixture Times Total Power On Time
Lamp On Time
Resettable Power On Time
Lamp On Time
Air Filt. Remain. 10-300
DMX Values Pan 0-255
:
Dimmer 0-255
Temperatures Current CPU
Head
Projector
Highest CPU
Head
Projector
High Res. CPU
Head
Projector
Power Channel
State
Software Versions Graphic Engine
Module Pan/Tilt
Module Optics
Module Display
Space Usage Free
Used
Product IDs
Wireless State Signal Quality
Unlink Wireless
Personality Pan Reverse On, O󰀨
Tilt Reverse On, O󰀨
Pan/Tilt Mode Speed Mode
Time Mode
Pan/Tilt Feedback On, O󰀨
Blackout DMC On, O󰀨
Blackout While Pan/Tilt Moving On, O󰀨
Colour Mixing Mode CMY Mode
RGB Mode
Init E󰀨ect position Pan 0-255
:
Dimmer 0-255
Display Orientation Normal, Inverted

17
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7
Screen Delay 0-10
Intensity 0-9
LED Engine Ceiling Projection On, O󰀨
Rear Projection On, O󰀨
Colour Temperature 3200K, 4200K, 5000K,
5500K,
5600K,6500K, 7500K,
8000K,9050K Max.
Brightness
Gamma Curve 1.8, 2.2, 2.4, B&W,
Linear
Gaphics Engine Image Aspect Ratio Fill Screen
Keep Aspect Ratio
Edge Antialiasing On
O󰀨
Gobo Selection Mode Alphabetical Order
Numerical Order
Gobo Synchro Mode On, O󰀨
Slideshow Timer 0...3...300
Optics Module None
Wide Optics
Fans Auto, High
Stand Alone Input Overtake O󰀨 , On
WEB Server Activate Password O󰀨, On
Set Password 2479
Wi Access Point Activate O󰀨
On
Channel ID 1-9
NAS Client Activate O󰀨 , On
IP Address
Synchro Time 10-600
On PowerUp Sync. O󰀨
No Wait For Sync
Wait For Sync
Reset to Defaults
Manual Control Manual DMX Control Pan 0-255
:
Dimmer. 0-255
LED Engine External Input On, O󰀨
Keystone Horizontal 0...128....255
Keystone Verical 0...128....255
LED On/O󰀨 On, O󰀨
Test Program Static Pan 0-255
Tilt 0-255
Focus 0-255
Run
Dynamic
Stand Alone Auto Run Play O󰀨
Program 1-Program 9
Play Program Program 1-Program 9
Record Program Program 1-Program 9
Edit Program Program 1-Program 9 Step 1 Pan 0-255
: :
Step Dimmer 0-255
Step Time 0.1-999.9s

18
Add New Step
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7
Delete Step
Reset Functions Reset Grap. Engine
Reset Pan/Tilt
Reset Focus
Reset All
User Media Initiaize USB
Mirror Media
Mirror Program
Re-encode Internal
Media
Delete Internal Media
Special Functions Reinit Inner Flash
Drive
Calibration Pan Calibration 0-255
Tilt Calibration 0-255
Focus Calibration 0-255
Grey Box calibration 0--255
Store

19
5. Control menu
The Robin ProMotion is equipped with Robe Graphic Touch Screen (50x40mm / 1.97" x 1.57") which allows
you to set the xture´s behaviour according to your needs, obtain information on its operation and program it,
if it has to be used in a stand-alone mode.
After switching the xture on and performing xture reset, the following screen with DMX address will appear.
Touch the screen to display main menu of the xture.
Touch the Main Menu to enter main menu of the xture.
5.1 Fixture Address
DMX Address - Use the menu item to set desired DMX start address of the xture, which is dened as the rst
channel from which the Robin ProMotion will respond to the controller.
If you set, for example, the address 26, the Robin ProMotion will use channels 26 - 50 for control. Please, be
sure that you do not have any overlapping channels in order to control each Robin ProMotion correctly and
independently from any other xture on the DMX data link.
ArtNet Universe - Use the menu item to set desired ArtNet Universe (0-255).
sACN Universe - Use the menu item to set desired sACN Universe. (1-63999)
Receiving Mode - Use the menu item to set DMX operating mode (" DMX"), ArtNet operation mode ("ArtNet"),
sACN operating mode ("ACN") or wireless DMX ("Wireless DMX").
IP Addr - Set IP Address. Use this menu to set desired IP address of the xture.
IP NetMask - Use the menu item to set desired NetMask of the xture.
Reset Addreses - Use the menu item to set IP address, netmask and Artnet universe to default values.
Touching and holding nger on
the display rotates menu 180 degrees
from current orientation.

20
5.2 Fixture information
Fixture Times - Use the menu to read a number of xture operation hours.
Total
Power On Time - The menu item shows a total number of operation hours since
the Robin ProMotion has been fabricated.
Lamp On Time - The menu item shows a total number of LED source operation hours
since the Robin ProMotion has been fabricated.
Resettable
Power On Time - The item shows a total number of operation hours when the Robin
ProMotion has been powered on since the counter was last reset.
In order to reset this counter to 0, touch the item.
Lamp On Time - The item shows a total number of operation hours of LED source when
the Robin ProMotion has been powered on since the counter was last reset.
In order to reset this counter to 0, touch the item.
Air Filt. remains -The item allows you to read the time which remains to cleaning
air lter.The time period can be set in a interval of 10-300 hrs.
Regular cleaning of the air lter (placed in xture base) is very important for the xture´s
life and performance. Dust, dirt and fog uid residues reduces the xture´s light output
and cooling ability.
DMX Values -Use the menu item to read DMX values of each channel received by the xture.
Temperatures - The menu shows temperatures in the xture.
Current
CPU- A current temperature of the Raspberry in the xture base.
Head - A current temperature in the xture head.
Projector - A current temperature in the projector.
Highest
CPU- A maximum temperature of the Raspberry since the xture has been fabricated.
Head - A maximum temperature in the xture head since the xture has been fabricated.
Projector - A maximum temperature in the projector since the xture has been
fabricated.
High Res.
CPU- A maximum temperature of the Raspberry since the counter was last reset.
Head - A maximum temperature in the xture head since the counter was last reset.
Projector - A maximum temperature in the projector since the counter was last reset.
To reset desired temperature, touch its item on the screen.
Power Channel State - Select this item to see current setting of the functions, which can be set by menu items
in "Personality" as well as by DMX command at the channel "Special functions".
Software Versions - Use the menu item to read software versions of the xture modules.
Graphic Engine - A graphic engine.
Module Pan/Tilt - A pan/tilt/control module.
Module Optics - A focus/grey box control module
Module Display - A display control module
Space Usage - Use this item to read free and used space on the internal USB ash drive.
Free- A free space (MB).
Used - A used space (MB).
Product IDs - Use this item to read Mac address, RDM UID and LED Engine (version of LED module).
Wireless State - The menu serves for reading of the wireless operation status.
If the xture is linked to a DMX transmitter, the information about signal quality will be displayed and the option
Unlink Wireless serves for unlinking the xture from a DMX transmitter.
If the xture is unlinked from a DMX transmitter, the message "Wireless Module is Unlinked" will be displayed.
Unlink Wireless Adapter - The item serves for unlinking the xture from DMX transmitter.