Robert Juliat TIBO User manual

LED SINGLE LENS LUMINAIRE /
VALIDATION : 18/05/17
DN41043201-A
Robert Juliat S.A.S. 32, rue de Beaumont, F 60530 Fresnoy-en-Thelle - phone : [phone] - fax : [phone] - [email protected]
www.robertjuliat.com
Manual / Manuel
535 CW - Version V4 – 01/2017
535 WW - Version V4 – 01/2017
535 NW - Version V4 – 01/2017
535 VW - Version V4 – 01/2017
Temperature Standard North American
Température Standard Nord-Américain
6500 K (COOL WHITE) 535 CW 535 CCW
3000 K (WARM WHITE) 535 WW 535 CWW
4000 K (NEUTRAL WHITE) 535 NW 535 CNW
2700 K --> 5700 K (VARIABLE WHITE) 535 VW 535 CVW

Robert Juliat reserve the right to change or alter any of the items detailed on this page,
to increase or improve manufacturing techniques without prior notice.
Table of Contents
1 User’s instructions..........................................................................................................................................................1
2 Presentation ....................................................................................................................................................................2
2.1 Functions.............................................................................................................................................................. 2
2.2 Identication label.............................................................................................................................................. 2
2.3 Accessories included ........................................................................................................................................... 3
2.4 Optional accessories........................................................................................................................................... 3
3 Set-up ...............................................................................................................................................................................4
3.1 Mechanics ............................................................................................................................................................ 4
3.1.1 Operating positions....................................................................................................................................................4
3.1.2 Minimum distance between a ammable material and the lighting unit...................................................4
3.1.3 Instructions for use .....................................................................................................................................................4
3.1.4 Hanging ........................................................................................................................................................................5
3.1.5 Safety cable..................................................................................................................................................................5
3.2 Electrical data...................................................................................................................................................... 6
3.2.1 LED source ....................................................................................................................................................................6
3.2.2 Power Supply................................................................................................................................................................6
3.2.3 Data ...............................................................................................................................................................................8
3.3 Accessories ......................................................................................................................................................... 10
3.3.1 Front lter holder ......................................................................................................................................................10
3.3.2 Barndoors ...................................................................................................................................................................10
4 Operation.......................................................................................................................................................................11
4.1 Light intensity.................................................................................................................................................... 11
4.1.1 Range...........................................................................................................................................................................11
4.1.2 Control.........................................................................................................................................................................11
4.1.3 Parameters .................................................................................................................................................................11
4.2 Strobe ................................................................................................................................................................. 12
4.2.1 Range...........................................................................................................................................................................12
4.2.2 Control.........................................................................................................................................................................13
4.3 CCT adjustment (only for Variable White version, 535 VW) ......................................................................... 13
4.3.1 Range...........................................................................................................................................................................13
4.3.2 Control.........................................................................................................................................................................13
4.4 Beam size adjustment....................................................................................................................................... 14
4.4.1 Range...........................................................................................................................................................................14
4.4.2 Control.........................................................................................................................................................................15
4.5 Orientation ........................................................................................................................................................ 15
4.5.1 Range...........................................................................................................................................................................15
4.5.2 Control.........................................................................................................................................................................16
4.6 Colour ................................................................................................................................................................. 16
4.7 Beam shaping (Barndoors) .............................................................................................................................. 17
4.7.1 Range...........................................................................................................................................................................17
4.7.2 Control.........................................................................................................................................................................17
4.8 Control................................................................................................................................................................ 18
4.8.1 Display and Controls................................................................................................................................................18
4.8.2 Menus and parameters..............................................................................................................................................18
4.8.3 DMX chart...................................................................................................................................................................18
4.8.4 Reset.............................................................................................................................................................................19
4.8.5 Feedback information .............................................................................................................................................19
5 Service ............................................................................................................................................................................19
5.1 Preventive maintenance ................................................................................................................................... 19
5.1.1 Frequency ...................................................................................................................................................................19
5.1.2 General cleaning.......................................................................................................................................................19
5.1.3 General visual check ................................................................................................................................................19
5.1.4 LED source ..................................................................................................................................................................20
5.1.5 Optics...........................................................................................................................................................................20
5.2 Analysis .............................................................................................................................................................. 20
5.3 LED reaction according to LED temperature.................................................................................................. 20
5.4 Adjusting the maximum light output level .................................................................................................... 20
5.5 Exploded view / Spare parts list....................................................................................................................... 20
6 Troubleshooting ...........................................................................................................................................................21

EN
EN - 1 -
1 User’s instructions
GENERAL INSTRUCTIONS
1. Not for residential use.
2. These fixtures must only be serviced by a qualified technician.
3. In addition to the instructions indicated on this page, relevant health and safety requirements of the appropriate EU
Directives must be adhered to at all times.
4. This fixture is in compliance with section 17 - Lighting appliance for theatre stages, television, cinema and photograph
studios. Standards NF EN 60598-1 and NF EN 60598-2-17.
5. This fixture is rated as IP20, and is for indoor use only.
FIXTURE
6. Ensure fixture is correctly mounted on an appropriate support.
7. Protection screens and lenses must be replaced in the event of any damage, such as cracks or deep scratches, since
these might reduce performance.
8. When hung or flown the fixture must be secured by an additional hanging accessory (such as a safety cable or bond) of
suitable length.
9. Safety bonds or cables must be securely attached to the back of the fixture and be as short as possible, or
rolled up as necessary, to minimise travel distance should the fixture be dislodged.
10. Movable accessories (scroller, etc.) must also be secured with a suitable safety cable or bond at the front of the fixture.
11. The combined weight of both the fixture and the accessories must be considered when choosing the load-bearing
capability of safety cable or bond.
12. Do not open lighting fixture when the source is on.
13. WARNING: LED source become hot during use. Allow fixture to cool before servicing.
14. Do not tamper with design of fixture nor any of its safety features.
15. Tighten electrical mains cable connections regularly and replace with one of identical specification if damaged.
16. Use only with correct power supply.
VENTILATION
17. Keep well away from flammable material.
18. Not for outdoor use. Do not cover. Do not permit fixture to get wet.
19. To avoid overheating, do not obstruct air vents.
20. Ensure any cooling fans are in correct working order. If fans are not working, turn fixture off immediately and service as
necessary.
CLEANING
21. Do not touch LED source with fingers.
22. Clean all optical parts with alcohol-based cleaner.
23. Clean all filters regularly.
POWER SUPPLY
24. Disconnect from the mains before servicing.
25. Mains connection only. Do not connect to "electronic output" such as dimmer.
26. Not for outdoor use. Do not cover.
27. Ensure power supply circuit breakers, always remain accessible.
PLEASE NOTE
These products have been built to conform to European standards relating to professional lighting equipment. Any modification
made to our products will void the manufacturers' warranty.

EN
535 CW/NW/WW
535 VW
DE41013508
Uled =40V max
t°a = 40°C
t°c = 60°C
IP20
Iled = 0,7A max
Made in the EU - France -
kg
0,3m
6Kg
Fresnel
VW
Read the manual before use. Disconnect xture before servicing.
Not for residential use. Avoid contact with persons and materials.
Caution, hot surfaces. Service only by qualied technician. /
Lire le manuel avant utilisation. Débrancher l’appareil avant toute
intervention. Impropre à l’usage domestique. Eviter tout contact
avec les personnes et les objets. Attention surfaces chaudes.
Intervention par technicien qualié.
VW
Serial N°
1 2
USE ONLY / SEULEMENT AVEC
PSU / ALIM. : TT-MNW 36W
DE41013504
Uled = 58V max
t°a = 40°C
t°c = 60°C
IP20
Iled = 1,4A max
Made in the EU - France -
kg
0,3m
6,2Kg
Fresnel
LED
Read the manual before use. Disconnect xture before servicing.
Not for residential use. Avoid contact with persons and materials.
Caution, hot surfaces. Service only by qualied technician. /
Lire le manuel avant utilisation. Débrancher l’appareil avant toute
intervention. Impropre à l’usage domestique. Eviter tout contact
avec les personnes et les objets. Attention surfaces chaudes.
Intervention par technicien qualié.
L
Serial N°
USE ONLY / SEULEMENT AVEC
PSU / ALIM. : T-MNW 75W
1 2
EN - 2 -
2 Presentation
2.1 Functions
2.2 Identication label
Functions
1. Colour temperature version :
●CW = Cool White
●NW = Neutral White
●WW = Warm White
●VW = Variable White
2. Data connectors (IN and OUT)
3. Power connectors (IN and OUT)
4. Thermal breaker
5. Power switch
6. Control board
7. Wireless DMX antenna (option*)
(*) Not available for the VW version
8. Handle
9. Safety cable attachment point
10. Hanging yoke
11. Tilt index
12. Tilt locking handle
13. Focus adjustment
14. Front slot for accessory and gel frame
15. Front slot locking system
16. Safety cable attachment point for accessories
17. Unit rotation
Description
1. Serial number
2. Version

EN
EN - 3 -
2.3 Accessories included
2.4 Optional accessories
Reference Description
1 OmegaT2 Omega clamp with quarter turn bolt sets
2 W-DMX/T W-DMX wireless DMX*
(*) NOT available for the Variable White version.
3 CF100 4 rotating leaves on a barndoor 135 x 135 mm
(without safety cable)
4 872 Doughty Twenty clamp with M10 screw/nut for Ø48 to 51mm pipes –
SWL: 20Kg - TÜV approved
5 878 Hook clamp 25x6 with 23mm screw for Ø35 to 50mm pipes – SWL: 11Kg
6 CS2 Safety cable Ø3 mm L= 600mm - SWL: 75 Kg
7 EXT/TiboFW 12 pins extension cable - length 3.5m (138")
for Tibo LED 533 CW / WW / NW models
8 EXT/TiboVW 12 pins extension cable - length 3.5m (138") for Tibo LED VW model
1
4
2
56
3
Reference Description
1 PF100M 135x135 mm metal filter holder
2 Power cable with CEE7/7 type IN connectors (standard version)
3UL/CSA Power cable without connector
(North American version)
8
7
1
2 3

EN
EN - 4 -
3 Set-up
3.1 Mechanics
3.1.1 Operating positions
3.1.2 Minimum distance between a ammable material and the lighting unit
3.1.3 Instructions for use
Minimum :
40°C
104°F
5°C
41°F
IP20 - Indoor use only
Maximum :
0,3 m
1 ft

EN
EN - 5 -
3.1.4 Hanging
• Ensure fixture is correctly mounted on an appropriate support.
• Net weight for 535 CW, NW and WW versions :
- Fixture without power supply = 9,8 kg (21.6 lbs)
- Stand-alone power supply = 2,2 Kg (4.85 lbs)
• Net weight for 535 VW version :
- Fixture without power supply = 10 kg (22 lbs)
- Stand-alone power supply = 2,4 Kg (5.29 lbs)
3.1.5 Safety cable
• When hung or flown, the fixture must be secured by an additional hanging
accessory (such as safety bond or cable) of suitable length.
• Safety cables or bonds must be securely attached to the back of the fixture and be as
short as possible, or rolled up as necessary, to minimise travel distance should the
fixture be dislodged.
NOTA:
The indicated attachment points are symmetrical.
Warning : attachment point for
accessories only
Do not use as a hanging point
to secure the fixture.
M13 maxi
Ø13,20 mm
M13 maxi
Ø13,20 mm
M13 maxi
Ø13,20 mm
Position 1 Position 2 Position 3
Position 1 Position 2 Position 3

EN
EN - 6 -
3.2 Electrical data
3.2.1 LED source
Do not touch the surface of the LED source
(no contact with your hands or any tools).
• Do not put compressed air directly on the source.
• Contact a certified RJ distributor in case of residuals or other objects located
on the surface of the LED source.
3.2.2 Power Supply
Power supply
Voltage Frequency Input power Connectors
CW
NW
WW
90 —> 264 V 47-63 Hz
0.42 A / 95 W @ 230V
0.8 A / 95 W @ 120V
0.95 A / 95 W @ 100V
Max. 1.2 A
Standby mode: 7 W
Neutrik®powerCON TRUE1
ref. NAC3PX (max. 20A)
VW 90 —> 264 V 47-63 Hz
0.17 A / 36 W @ 230V
0.3 A / 36 W @ 120V
0.36 A / 36 W @ 100V
Max. 0.38 A
Standby mode: 7 W
Neutrik®powerCON TRUE1
ref. NAC3PX (max. 20A)
• Class 1 product. This luminaire must be grounded.
• Must be connected directly to AC power. Do not connect to dimmer power.
• Automatic power detection.
• 4A breaker.
• Daisy chain: maximum of 35 units (230V) / 20 units (120V)
Daisy chain (with delivered power cable): Maximum:
35 units (230V)
20 units (120V)

EN
EN - 7 -
Power cable
Power cable Connector Mains plug Cable type Cable length Wiring
1 Standard
version Neutrik®
powerCON
TRUE1
NAC3FX
CEE7/7 3G1.5
H07RNF
3 m
9.8 ft
Live: Brown
Neutral: Blue
Ground: Yellow/Green
2
North
American
version
-
14AWG
SJ TYPE
(UL/CSA)
1.5 m
4.9 ft
Live: Black
Neutral: White
Ground: Green
21
In Out
Power up
CW / WW / NW
VW
T-MNW 75W
TT-MNW 36W
Set-up

EN
DMX OUT DMX IN
Daisy chain:Maximum:
32 units
EN - 8 -
3.2.3 Data
DATA
Voltage Input connector Output connector
USITT DMX 512-A XLR 5-pin XLR 5-pin
DATA connectors
PIN # DMX Description
1Shielding Foil & Braided Shield
2DMX (-) 1st conductor of 1st twisted pair
3DMX (+) 2nd conductor of 1st twisted pair
4Not used 1st conductor of 2nd twisted pair
5Not used 2nd conductor of 2nd twisted pair
Integrated terminal plug:
If no XLR connector is detected on DMX OUT connector, a 120Ω terminal plug is automatically activated.
Additional terminal plug on the last unit is not necessary.

EN
EN - 9 -
Wireless DMX option (not available for the Variable White version)
The first unit receives the DMX signal via the wireless network, then all the other units are connected to
the first one via DMX data cable.
DMX mode:
Maximum:
32 units
• Protocol: Wireless Solution W-DMX™
• Refer to the OEM User’s manual for general recommendations and
use of the transmitter: http://www.wirelessdmx.com
• The antenna must be clearly visible from the transmitter.
• Refer to RJ-LED Software manual for activation procedure (page EN-15).
• Do not connect a DMX IN data cable in case of wireless DMX use.
• In case of protocol errors, the wireless DMX is automatically
deactivated. To activate the wireless DMX again, disconnect the
DMX IN data cable, and then switch the unit off and on.

EN
EN - 10 -
Step 1
3.3 Accessories
3.3.1 Front lter holder
3.3.2 Barndoors
Step 2

EN
0% 100%
EN - 11 -
4 Operation
4.1 Light intensity
4.1.1 Range
4.1.2 Control
Remotely with DMX512-A protocol Locally via control panel
4.1.3 Parameters
Resolution (RESOLUTION):
Curve (LIGHT CURVE): Linear / Square
HTP mode (Highest Takes Precedence):
Light output is the highest value of DMX512 command or local control
Focus mode: when standby screen displayed,
Push Exit →Light output = 100% for 1 minute
2x times Exit →Light output = 0%
Mode Resolution
8 bits 255 steps – 1 DMX channel
16 bits 65 535 steps – 2 DMX channels
DMX512-A

EN
EN - 12 -
Smoothing (SMOOTHING) :
Master mode (MASTER CONTROL):
→Mode required when simultaneous remote and local control are necessary (example: followspot)
4.2 Strobe
4.2.1 Range
DMX Local Light Output
8/16 bits Master
0 →100% 100% 0% 0 →100%
0 →100% 50% 0% 0 →50%
0% 100% 0 →100% 0 →100%
0% 50% 0 →100% 0 →50%
50% 100% 0 →100% 50 →100%
30% 80% 0 →100% 30 →80%
Mode Smoothing
Slow Slow transition between 2 levels – equivalent to 1000W filament
Fast Fast transition between 2 levels – equivalent to 600W filament
Without Deactivated – Very fast transitions
1
0 = OFF
255
1Hz 55Hz

EN
DMX512-A
EN - 13 -
4.2.2 Control
Remotely with DMX512-A protocol
4.3 CCT adjustment (only for Variable White version, 535 VW)
4.3.1 Range
Warm White Cold White
4.3.2 Control
Remotely with DMX512-A protocol Locally via control panel
HTP mode (Highest Takes Precedence):
Light output is the highest value of DMX512 command or local control
DMX512-A

EN
EN - 14 -
4.4 Beam size adjustment
4.4.1 Range
Model Angles Minimum angle Maximum angle
535 CW / CCW Beam angle 35° 31°
Field angle 55° 87°
535 WW / CWW Beam angle 34° 31°
Field angle 54° 87°
535 NW / CNW Beam angle 34° 33°
Field angle 53° 84°
535 VW / CVW Beam angle 35° 32°
Field angle 54° 87°
Beam angle
50%
Field angle
3%

EN
EN - 15 -
4.5 Orientation
4.5.1 Range
Function Range
PAN 0 —> 360°
TILT
TU = 0 —> 90°
TU = 0 —> 90°
4.4.2 Control

EN
EN - 16 -
4.5.2 Control
PAN TILT
Type Standard coloured gel filter
Dimensions
Installation See section 3.3.1
Values are in mm
4.6 Colour
Fixed colour:

EN
EN - 17 -
4.7.2 Control
4.7 Beam shaping (Barndoors)
4.7.1 Range
1 leaf 2 leaves 3 leaves 4 leaves
Open

EN
EN - 18 -
4.8 Control
4.8.1 Display and Controls
1 42 5 6 73
4.8.2 Menus and parameters
4.8.3 DMX Chart
Function
1Display
2Exit the current menu option and/or go back
3Scrolls through menus and/or Decrease blinking data value
4Scrolls through menus and/or Increase blinking data value
5Enter the current menu option and/or valid
6Hard CPU reset
7DMX and system LED feedback
Please scan this QR-Code for the software menu or go to :
www.robertjuliat.com/productSearch.html to nd the latest version.
Mode Theatre Studio Followspot Direct DMX (variable
white)
DMX ch.
1Dimmer (8 bit) Dimmer Coarse (8 bit) Dimmer Coarse (8 bit) WW Coarse (8 bit)
2Dimmer Fine (16 bit) Dimmer Fine (16 bit) WW Fine (16 bit)
3CCT
0255 : WW CW
CCT
0255 : WW CW CW Coarse (8 bit)
4Strobe
0 :OFF ; 1 255 : SLOW FAST
Strobe
0 :OFF ; 1 255 : SLOW FAST CW Fine (16 bit)
5Master
0 255 : 0 100% (FULL)
Strobe
0 :OFF ; 1 255 : SLOW FAST