Robert Juliat Dalis-862S User manual

EN
DALIS – 862S
Firmware V1.XX – 15/11/17
DN41136200
Robert Juliat S.A.S. 32, rue de Beaumont, F60530 Fresnoy-en-Thelle - phone : [phone] - fax : [phone] - [email protected]
Dalis – 862S
Footlight
Projecteur bain de pied LED 75 W - Blanc variable
LED 75 W - Variable White Footlight
For more information,
Please download the full manual online
http://www.robertjuliat.com/ambiance_lighting/dalis862.html
Package contents:
1x Dalis 862S
1x Neutrik PowerCon© True1 connector
(ref. NAC3FX-W)
Quick start guide

EN
EN -1-
1 User’s instructions
GENERAL INSTRUCTIONS
1. Not for residential use.
2. These fixtures must only be serviced by a
qualified technician.
3. In addition to the instructions indicated on this page,
relevant health and safety requirements of the
appropriate EU Directives must be adhered to at all
times.
4. This fixture is in compliance with section 17 - Lighting
appliance for theatre stages, television, cinema and
photograph studios. Standards NF EN 60598-1 and
NF EN 60598-2-17.
5. This fixture is rated as IP20, and is for indoor use
only.
FIXTURE
6. Ensure fixture is correctly mounted on an appropriate
support.
7. Protection screens must be replaced in the event of
any damage, such as cracks or deep scratches, since
these might reduce performance.
8. When hung or flown the fixture must be secured by
an additional hanging accessory (such as a safety
cable or bond) of suitable length
9. Safety bonds or cables must be securely attached to
the fixture and be as short as possible, or rolled up as
necessary, to minimise travel distance should the
fixture be dislodged.
10. WARNING: LED source become hot during use.
Allow fixture to cool before servicing.
11. Do not tamper with design of fixture nor any of its
safety features.
12. Tighten electrical mains cable connections regularly
and replace with one of identical specification if
damaged.
13. Use only with correct power supply.
14. Do not orientate the fixture towards a source of light
(sun, fixture), in particular for LED versions.
VENTILATION
15. Keep well away from flammable material.
16. Not for outdoor use. Do not cover. Do not permit
fixture to get wet.
17. To avoid overheating, do not obstruct air vents– do
not cover the unit.
PLEASE NOTE
These products have been built to conform to European
standards relating to professional lighting equipment. Any
modification made to our products will void the
manufacturers' warranty.
2 Installation
Floor installation only

EN
EN -2-
3 Electrical / Data connection
1
Power input :
• Connector: Neutrik powerCON TRUE1
• Voltage: 90 à 264V 50/60Hz
• Power consumption: 90 W max.
2
Power output:
• Connector: Neutrik powerCON TRUE1
• Daisy chain:
§ 230 V: 30 units max
§ 120 V: 15 units max
§ 100 V: 12 units max
3
Data In:
• Connector: XLR 5-pin
• Protocol: USITT DMX 512-A / RDM
4
Data Out:
• Connector: XLR 5-pin
• Protocol: USITT DMX 512-A / RDM
5
Ethernet:
• Connector: RJ45
• Protocol: Art-Net / sACN + software update
4 DMX control
DMX address and control mode selection:
Data Mode
DMX
DMX Address
Start addresss : XXX
Mode X : XXXXXXX
Main screen
Personality
1
2
4
3
5

EN
EN -3-
5 DMX chart
DMX
address
Mode 1:
Full4groupsmode
16b
Mode 2:
Full1groupmode
16b
Mode 3:
Full1groupmode
8b
Mode 4:
Presetmode
16b
Mode 5:
Presetmode
8b
Mode 6:
4groupsindividual
16bits
Mode 7:
4groupsindividualpreset
16b
1
Dimmer
Dimmer - US
Dimmer - US
Dimmer
Dimmer
Dimmer - US1
Dimmer - 1
2
Dimmer fine
Dimmer fine - US
Cool white - US
Dimmer fine
Balance
Dimmer fine - US1
Dimmer fine - 1
3
Cool white - US1
Cool white - US
Warm white - US
Balance
CCT
Cool white - US1
Balance - 1
4
Cool white fine - US1
Cool white fine - US
Dimmer - DS
CCT
Strobe duration
Cool white fine - US1
CCT - 1
5
Warm white - US1
Warm white - US
Cool white - DS
Strobe duration
Strobe speed
Warm white - US1
Blue position intensity - 1
6
Warm white fine - US1
Warm white fine - US
Warm white - DS
Strobe speed
Response time
Warm white fine - US1
Red position intensity - 1
7
Cool white - US2
Dimmer - DS
Strobe duration
Response time
Control mode
Dimmer - US2
Dimmer - 2
8
Cool white fine - US2
Dimmer fine - DS
Strobe speed
Control mode
Blue position
Dimmer fine - US2
Dimmer fine - 2
9
Warm white - US2
Cool white - DS
Response time
Blue position
Red position
Cool white - US2
Balance - 2
10
Warm white fine - US2
Cool white fine - DS
Control mode
Red position
Position Intensity
Cool white fine - US2
CCT - 2
11
Cool white - DS1
Warm white - DS
Blue position
Position Intensity
Warm white - US2
Blue position intensity - 2
12
Cool white fine - DS1
Warm white fine - DS
Red position
Warm white fine - US2
Red position intensity - 2
13
Warm white - DS1
Strobe duration
Position Intensity
Dimmer - DS1
14
Warm white fine - DS1
Strobe speed
Dimmer fine - DS1
15
Cool white - DS2
Response time
Cool white - DS1
16
Cool white fine - DS2
Control mode
Cool white fine - DS1
17
Warm white - DS2
Blue position
Warm white - DS1
18
Warm white fine - DS2
Red position
Warm white fine - DS1
19
Strobe duration
Position Intensity
Blue position intensity - 1
20
Strobe speed
Red position intensity - 1
21
Response time
Dimmer - DS2
22
Control mode
Dimmer fine - DS2
23
Blue position
Cool white - DS2
24
Red position
Cool white fine - DS2
25
Position Intensity
Warm white - DS2
26
Warm white fine - DS2
27
Blue position intensity - 2
28
Red position intensity - 2
Group 2
Group 1
US = Up Stage
DS = Down Stage