ROBERTO FIORE Cabinets To Go BC12 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Base Cabinets
ITEM No.:BC12 BC15 BC18 BC21
Page 1

►Items Quantity
Item Description Qty
Door 1
B
Drawer Front 1
C Side Panels (Left & Right)
2
D Back Panel
1
E Bottom Panel 1
F
Toe Kick
1
G
Shelf
3
Hinges 2pcs, Bumpers 6pcs, 2/3" Flat Head Screws 4pcs, 2/3" Round Head Coarse Thread Screws 8pcs, Cam Locks Male & Female 22pcs, Wooden Dowels 14pcs, Shelf Pins 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b e
Qty 22
f
Qty 14
cd
Qty 2 Q ty 6 Qty 4Qty 8
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
A
C
B
F
E
A
H
I
Braces
2
1
C
G
I
H
H
Drawer Box (Back Panel & Bottom Panel)
g
Qty 4
h
Qty 1
European Drawer Box Kit 1pc
Hardware Box
D
G

Page 3
►Instructions:
1.Unpack box & identify pieces on Page 2. Place
side panel (C) onto a soft work surface.
(Figure 1)
2.Install Hinge base plates (a) onto side panel (C)
into designated holes using screws (d). Install
glides onto side panels. (Figure 2)
(Glides and screws found in the European Drawer Box Kit.)
3.Install metal male cam locks (e) into designated
holes on side panel (C) and bottom panel (E). Use
screwdriver to tighten. Install the wooden dowels
(f) into designated holes. (Figure 3)
4.Install the toe kick (F) onto bottom panel (E).
(Figure 3)
5.Install braces (G) & back panel (D) onto the right
side panel (C). (Figure 3)
6.Install locking lugs (e) into designated holes, and
then lock them with a screwdriver. (Figure 4)
7.Install side panel (C) onto the assembled panels
using the same methods above. (Figure 5)
Figure 1
SoftSurface
Hard Surface
C
C
Figure 2 Base Plate
Figure 3
Figure 4
Figure 5
a
Qty 2
d
Qty 8
e
Qty 22
f
Qty 14

5.
9.Install hinges onto door into designated holes using screws provided.
Page 4
c
Qty 4
b
Q ty 6
a
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong ble
ach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the q uality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
g
Qty 4
Install door onto cabinet sides though pre-marked screw holes.
Install the shelf (I) by using shelf pins (g) in the location you choose.
Install the bumpers (b) onto the door corners opposite of the hinges.
Figure 6
8.Install the drawer as the images below. (Figure 6)