ROBERTO FIORE Cabinets To Go BC30 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Base Cabinets
ITEM No.:BC30 BC33 BC36
Page 1

►Items Quantity
Item Description Qty
Door 2
B
Drawer Front 2
C Side Panels (Left & Right)
2
D Back Panel
1
E Bottom Panel 1
F
Toe Kick
1
G
Shelf
4
Hinges 4pcs, Bumpers 12pcs, 2/3" Flat Head Screws 8pcs, 2/3" Round Head Coarse Thread Screws 16pcs, Cam Locks Male & Female 24pcs, Wooden Dowels 16pcs, Shelf Pins 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b e
Qty 24
f
Qty 16
cd
Qty 4 Q ty 12 Qty 8Qty 16
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
A
C
B
F
E
A
H
I
J
Braces
2
Center Braces
C
G
G
G
J
H
Drawer Box (Back Panel & Bottom Panel)
2 each
I
I
g
Qty 4
h
Qty 16
i
Qty 2
Flat Head Screws 16pcs, European Drawer Box Kit 2pc
Hardware Box
1
D
B
A
I
I

Page 3
3. Install opposite glides onto the center braces (H).
Then attach the 2 center braces (H) and 4 braces (G) together using screws (h). (Figure 3)
6. Install the other side panel (C) using the same method from step 5. (Figure 6)
Figure 1
SoftSurface
Hard Surface
C
C
►Instructions:
1. Unpack box/identify pieces on Page 2. Place side panels (C) onto a soft work surface. (Figure 1)
2. Install hinge base plates (a) and glides (i) onto side panels (C) using designated holes and screws
provided. (Figure 2) (Glides and screws found in the European Drawer Box Kit.)
d
Qty 16
Qty 4
Figure 2
h
Qty 16
Base Plate
a
Figure 3
Qty 24
4. Install male cam locks (e) & wooden dowels (f) into designated holes on side panels (C). Use a screwdriver
to tighten. (Figure 4)
5. Install bottom panel (E), back panel (D), toe kick (F), & braces (G) onto side panel. (Figure 4)
Install locking lugs (e) into designated holes, and then lock them. (Figure 5)
e f
Qty 16
Figure 4
Figure 5
Figure 6
Male

8.Install hinges (a) onto door (A) into designated hinge holes (Figure 8)
Page 4
► Maintenance
For daily cleaning, use a dry cloth and a soft li
quid cleaner.
Never use abrasi
ve cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome -plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
c
Qty 8
b
Q ty 12
a
7. Install the drawer as the images below. (Figure 7)
Figure 7
Figure 8
g
Qty 4
using screws provided (c). Install doors onto cabinet sides by connecting the hinge to the pre-
installed base plates from Step 2. Apply bumpers (b) onto the door and drawer face corners.
Install the adjustable shelf (J) using shelf pins (g).