ROBERTO FIORE Cabinets To Go MBC30 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Microwave Base
ITEM No.:MBC30
Page 1

►Items Quantity
Item Description Qty
1
B
Drawer Front
1
C Side Panels (Left & Right)
2
D Back Panel
1
E Bottom Panel 1
F
Toe Kick
1
G
Shelf
2
1
Bumpers 4pcs, Cam Locks Male & Female 20pcs, Wooden Dowels 16pcs, European High Drawer Box Kit 1pc
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b
cd
Qty 4 Q ty 20 Qty 16 Qty 1
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
A
C
B
F
E
A
H
Braces
G
H
Drawer Box (Back Panel & Bottom Panel)
Hardware Box
D
C
G

Page 3
►Instructions:
1.Unpack box & identify pieces on Page 2. Place
side panels (C) onto a soft work surface.
(Figure 1)
2.Install glides onto side panels. (Figure 2)
(Glides and screws found in the European High Drawer Box Kit.)
3.Install metal male cam locks (b) into designated
holes on side panel (C) and bottom panel (E). Use
screwdriver to tighten. Install the wooden dowels
(c) into designated holes. (Figure 3)
4.Install the toe kick (F) onto bottom panel (E).
(Figure 3)
5.Install braces (G) & back panel (D) onto the right
side panel (C). (Figure 3)
6.Install locking lugs (b) into designated holes, and
then lock them with a screwdriver. (Figure 4)
7.Install side panel (C) onto the assembled panels
using the same methods above. (Figure 5)
Figure 1
SoftSurface
Hard Surface
C
C
Figure 2
Figure 3
Figure 4
Figure 5
b
Qty 20
c
Qty 16
d
Qty 1

5.
9.Install assembled drawer box into the assembled cabinet.
Page 4
a
Q ty 4
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not
use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and lo ok of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
Install the bumpers (a) onto the drawer front corners.
Figure 6
8.Install the drawer as the images below. (Figure 6)