ROBERTO FIORE Cabinets To Go SBA36 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all APRON SINK BASE
ITEM No.:SBA36
Page 1

►Items Quantity
Item Description Qty
Doors 2
B
Back Panel 1
C Side Panels Left & Right
2
D Front Brace
1
E Bottom Panel 1
F
Toe Kick
1
Hardware Box
Hinges 4pcs, Bumpers 12pcs, 2/3" Flat Head Screws 8pcs, 2/3" Round Head Coarse Thread Screws 16pcs, Cam Locks Male & Female 20pcs, Wooden Dowels 10pcs,
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b e
Qty 20
f
Qty 10
cd
Qty 4 Q ty 12 Qty 8Qty 16
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
A
C
G
F
E
A
g
Qty 4
C
B
D
A
Corner Braces 4pcs, 1/2" Round Head Screws 8pcs, 1 1/4" Coarse Thread Screws 4pcs
h
Qty 8
G
G
Uprights
2
i
Qty 4

Page 3
►Instructions:
1.Unpack box & identify pieces on Page 2. Place
side panels (C) onto a soft work surface.
(Figure 1)
2.Install Hinge base plates (a) onto side panels into
designated holes using screws (d).
(Figure 2)
3.Install metal male cam locks (e) into designated
holes on side panel (C) and bottom panel (E). Use
screwdriver to tighten. Install the wooden dowels
(f) into designated holes. (Figure 3)
4.Install the toe kick (F) onto bottom panel (E).
(Figure 3)
5.Install front brace (D) onto the right side panel (C).
(Figure 3)
6.Install locking lugs (e) into designated holes, and
then lock them with a screwdriver. (Figure 4)
7.Install side panel (C) onto the assembled panels
using the same methods above. (Figure 5)
Figure 1
SoftSurface
Hard Surface
C
C
Figure 2 Base Plate
Figure 3
Figure 4
Figure 5
a
Qty 4
d
Qty 16
e
Qty 20
f
Qty 10

5.
6.
Page 4
c
Qty 8
b
Q ty 12
a
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use ab
rasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under
no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quali ty and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
g
Qty 4
h
Qty 8
8.Install hinges onto doors into designated holes using screws provided.
Install doors onto cabinet sides though pre-marked screw holes.
Install the corner brackets (g) by using screws (h) in the cabinet corners.
Install the bumpers (b) onto the door corners opposite of the hinges.
Install the remaining bumpers onto the back of the Uprights (G), then
attach them to the front brace (D) using screws (i).
i
Qty 4