ROBERTO FIORE Cabinets To Go BBC42 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Blind Base Corner Cabinets
ITEM No.:BBC42 BBC45
Page 1

►Items Quantity
Item Description Qty
Door 1
B
Drawer Front 1
C Side Panels (Left & Right)
2
D Back Panel
1
E Bottom Panel 1
F
Toe Kick
1
G
Shelf
4
Hinges 2pcs, Bumpers 6pcs, 2/3" Flat Head Screws 4pcs, 2/3" Round Head Coarse Thread Screws 8pcs, Cam Locks Male & Female 30pcs, Wooden Dowels 19pcs, Shelf Pins 4pcs
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b e
Qty 30
f
Qty 19
cd
Qty 2 Q ty 6 Qty 4Qty 8
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
A
C
K
B
F
E
A
H
I
J
Braces
2
Center Braces
1
Center Front Stile
C
G
G
G
G
I
H
H
K
Drawer Box (Back Panel & Bottom Panel)
1 each
J
J
g
Qty 4
h
Qty 16
i
Qty 1
Flat Head Screws 16pcs, European Drawer Box Kit 1pc
*Diagram shown with the Door &
Drawer installed on the right side.
Hardware Box
1
D

Page 3
3. Install opposite glide onto the center brace (H) corresponding to the side panel you chose from step 2.
Then attach the 2 center braces (H) and 4 braces (G) together using screws (h). (Figure 3)
6. Install the center front stile (I) and the other side panel (C) using the same method from step 5. (Figure 6)
Figure 1
SoftSurface
Hard Surface
B
B
►Instructions:
1. Unpack box/identify pieces on Page 2. Place side panels (B) and center front stile (I) onto a soft
work surface. (Figure 1)
2. Install hinge base plates (a) onto center front stile (I), & 1 glide onto side panel (B) of your choice
using designated holes and screws provided. (Figure 2) (Glides and screws found in the European Drawer Box Kit.)
d
Qty 8
Qty 2
Figure 2
h
Qty 16
Base Plate
a
Figure 3
Qty 30
4. Install male cam locks (e) & wooden dowels (f) into designated holes on side panels (C). Use a screwdriver
to tighten. (Figure 4)
5. Install bottom panel (E), back panel (D), toe kick (F), & braces (G) onto side panel. (Figure 4)
Install locking lugs (e) into designated holes, and then lock them. (Figure 5)
e f
Qty 19
Figure 4
Figure 5
Figure 6
Male
(With the assembled braces aligned as shown in Figure 3, the glide should be
installed as shown for a left drawer/door BBC. Likewise, the glide should be
installed on the opposite center brace for a right drawer/door BBC.)

8.Install hinges (a) onto door (A) into designated hinge holes (Figure 8)
Page 4
► Maintenance
For daily cleaning, use a dry cloth and a soft
liquid cleaner.
Never use
abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
c
Qty 4
b
Q ty 6
a
7. Install the drawer as the images below. (Figure 7)
Figure 7
Figure 8
g
Qty 4
using screws provided (c). Install door onto cabinet center stile by connecting the hinge to the
pre-installed base plates. Apply bumpers (b) onto the door and drawer face corners. Install the
adjustable shelf (K) using shelf pins (g).