ROBERTO FIORE Cabinets To Go DC224 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Base 2-Drawer
ITEM No.:DC224--DC236
Page 1

►Items Quantity
Item Description Qty
2
B
Drawer Front
1
C Side Panels (Left & Right)
2
D
Back Panel
1
E
Bottom Panel
3
F
Toe Kick
1
G
Bumpers 8pcs, Cam Locks Male & Female 22pcs, Wooden Dowels 14pcs, European High Drawer Box Kit 2pc
► Required tools:
Page 2
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b
cd
Qty 8 Q ty 2 Qty 14 Qty 22
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
A
C
F
E
A
Braces
C
G
Drawer Box (Back Panel & Bottom Panel)
2 each
Hardware Box
D
B
A
E
E
G

Page 3
Figure 1
SoftSurface
Hard Surface
C
C
►Instructions:
1.Unpack box/identify pieces on Page 2. Place side panels (C) onto a soft work surface. (Figure 1)
2.Install glides (b) onto side panels (C) using designated holes and screws provided. (Figure 2)
(Glides and screws found in the European High Drawer Box Kit.)
Figure 2
Qty 22
Qty 14
5. Install the other side panel (C) using the same method from step 4. (Figure 5)
Figure 4
Figure 5
Male
b
Q ty 2
cd
Figure 3
3. Install male cam locks (d) & wooden dowels (e) into designated holes on side panels (C).
Use a screwdriver to tighten. (Figure 3)
4. Install bottom panel (D), back panel (B), toe kick (F), & braces (E) onto side panel. (Figure 3)
Install locking lugs (d) into designated holes, and then lock them. (Figure 4)

7.Install assembled drawer boxes onto the slides. (Figure 7)
Page 4
► Maintenance
For daily cleaning, use a dry cloth and a soft liqui
d cleaner.
Never use abrasive cleaners
containing acetone, chlorine or strong bleach. Also, do not use tool s as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
a
Q ty 8
6.Install the drawer as the images below. (Figure 6)
Figure 6
Figure 7
Apply bumpers (a) onto the drawer face corners.