Roberts All Weather Radio R9965 User manual

R9965
All Weather Radio
ROBERTS
Sound for Generations
Please read this manual before use
R9965.pmd 11/24/2003, 12:28 PM1

Contents ............................................................................ 2
Controls .......................................................................... 3-5
Battery Operation .............................................................. 6
Using the AC Adaptor ....................................................... 6
Listening to the radio - FM ................................................ 7
Listening to the radio - Medium and Long wave ............... 8
Headphones ...................................................................... 8
General .............................................................................. 9
Mains Supply ..................................................................... 9
Specification.................................................................... 10
Guarantee ........................................................................ 11
2
R9965.pmd 11/24/2003, 12:28 PM2

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
Controls
1. Tuning dial
2. Waveband switch
3. Tuning indicator
4. Low battery indicator
5. Volume Control
(Front)
2
4
3
5
1
3
R9965.pmd 11/24/2003, 12:28 PM3

Controls
(Left Side)
6. Rubber aerial
7. Carrying handle
4
7
6
R9965.pmd 11/24/2003, 12:28 PM4

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
Controls
(Right side)
8
5
8. Rubber socket cover
9. Headphone socket
10. DC input socket
910
R9965.pmd 11/24/2003, 12:28 PM5

Battery operation
1. Open the Battery cover on the rear of your radio by removing the
screw, lifting the cover flap and opening the door in a downward
direction.
2. Insert four LR14 (C size) batteries into the spaces in the compart-
ment. Take care to ensure all batteries are inserted with the correct
polarity as shown inside the battery compartment. Replace the
battery cover.
3. The low battery indicator will light when the batteries need replacing.
Using the AC adaptor
1. Place your radio on a flat surface.
2. Insert the adaptor plug into the DC socket located on the right side
of your radio.
3. Plug the adaptor into a standard 13 amp mains socket outlet.
Whenever the adaptor is used, the batteries are automatically
disconnected.
The AC adaptor should be disconnected from the mains supply and
the radio when not in use. The AC adaptor for use with the R9965
(Roberts type PU10) should provide 6 volts DC output at 1A, centre
pin negative.
We would recommend for economy that your radio is used via the
AC adaptor whenever possible with battery operation for occasional
or stand-by use only.
6
1
R9965.pmd 11/24/2003, 12:28 PM6

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
Listening to the radio - FM
1. Select 'FM' using the Waveband switch.
2. Adjust the Volume control until a hissing sound is heard.
3. If not already fitted, screw the Rubber aerial into place on the top
of the radio.
4. Carefully tune to the desired station using the Tuning control.
The Tuning indicator will light when the station is correctly tuned.
The FM band is marked on the upper half of the dial.
5. You may need to rotate your radio for optimum reception.
6. To switch off the radio set the Waveband switch to the 'Off'
position.
7
12
4
6
3
4
R9965.pmd 11/24/2003, 12:28 PM7

8
Listening to the radio - Medium and Long wave
1. Select 'MW' or 'LW' using the Waveband switch.
2. Adjust the Volume control until a hissing sound is heard.
3. Carefully tune to the desired station using the Tuning control.
The Tuning indicator will light when the station is correctly tuned.
The MW and LW bands are marked on the lower half of the dial.
4. You may need to rotate your radio for optimum reception.
5. To switch off the radio set the Waveband switch to the 'Off'
position.
Headphone socket
A 3.5mm Headphone Socket located on the right hand side of your
radio, is provided for use with either headphones or an earpiece.
Inserting the plug into the socket automatically mutes the internal
loudspeaker.
2
4
1
5
3
4
R9965.pmd 11/24/2003, 12:28 PM8

If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri) 9
Notes
R9965.pmd 11/24/2003, 12:28 PM9

Specifications
Power Requirements
Mains AC 230 volts, 50Hz only.
Batteries 4 x LR14 (C size)
Frequency Coverage
FM 87.5-108MHz
MW 522- 1600kHz
LW 144- 281kHz
Circuit Features
Loudspeaker 2 x 77mm 8ohms
Output Power 2 x 1.6 Watts
Headphone socket 3.5mm dia
Aerial System FM Rubber aerial
MW Built in Ferrite aerial
LW Built in Ferrite aerial
The Company reserves the right to amend the specification without notice.
10
R9965.pmd 11/24/2003, 12:28 PM10