ROBINHOOD RGT6WH User manual

RGT - SERIES
APPROVED Page 1 of 6
ISSUE: C
ECN 07 033
GRANGE II RANGE HOOD
MODEL
RGT6WH, RGT6 L, RGT6SS
RGT9WH, RGT9 L, RGT9SS
SERVICE MANUAL

RGT - SERIES
APPROVED Page 2 of 6
ISSUE: C
ECN 07 033
RGT6WH, RGT6BL, RGT6SS
RGT9WH, RGT9BL, RGT9SS

RGT - SERIES
APPROVED Page 3 of 6
ISSUE: C
ECN 07 033
ROBINHOOD GRANGE II
RGT6WH, RGT6 L, RGT6SS GRANGE II 600 – 3 SPEED
RGT9WH, RGT9 L, RGT9SS GRANGE II 900 – 3 SPEED
ITEM DESCRIPTION PART No.
WHITE BLACK S/STEEL
1 Body Wra er
2 & 9 Corner Plastic Family 101150WH 101150BL 101150BL
3 Filter Channel Clear 103709 103709 103709
4 Filter S ring 101221 101221 101221
5
Filter Aluminium 288 x
362.5
103793 103793 103793
Filter Charcoal 288 x
362.5
103793C 103793C 103793C
6 Recirculating Cover 103854WH 103854BL 103854BL
7 3 S eed Switch
Assembly
103417WH.SP 103417BL.SP 103417BL.SP
8 Diffuser 101112 101112 101112
10 Twin Motor Housing 103853 103853 103853
11 Recirculating Duct 103915 103915 103915
12 Switch Cover 600mm 103921 103921 103921
12 Switch Cover 900mm 103848 103848 103848
13 Duct Blanking Disk 103924 103924 103924
14 Lam 40Watt Candle
Sha e
102722 102722 102722
15 Duct Ada tor 110030 110030 110030

RGT - SERIES
APPROVED Page 4 of 6
ISSUE: C
ECN 07 033
SECTION 1.
MOTOR REMOVAL AND REPLACEMENT
1.1 REMOVE THE UNIT FROM ITS MOUNTING.
1.2 REMOVE THE FILTERS.
1.3 REMOVE DIFFUSER AND LIGHT BULB.
1.4 REMOVE REAR OR TOP BLANKING DISK.
1.5 REMOVE THE SWITCH BRACKET.
1.6 REMOVE SWITCH ASSEMBLY FROM THE SWITCH BRACKET.
1.7 REMOVE THE LID OF THE SWITCH ASSEMBLY DISCONNECT THE
WIRES FROM THE BACK OF THE SWITCH.
1.8 REMOVE THE VENT DUCT.
1.9 REMOVE THE MOTOR SECURING SCREWS (TWO SCREWS AT THE
REAR OF THE UNIT).
1.10 LIFT MOTOR HOUSING FRONT EDGE, DRAW POWER CABLE
THROUGH BACK.
1.11 REMOVE MOTOR HOUSE FROM BODY.
1.12 REASSEMBLE RANGEHOOD IN REVERSE TO PROCEDURE ABOVE,
TAKING CARE TO PULL AS MUCH OF THE POWER CORD OUT OF
THE BODY AS POSSIBLE.
1.13 TEST TO ELECTRICAL SAFETY STANDARDS.
SECTION 2.
SWITCH REPLACEMENT
2.1 REMOVE THE SWITCH BRACKET.
2.2 REMOVE SWITCH ASSEMBLY FROM THE SWITCH BRACKET.
2.3 REMOVE THE LID OF THE SWITCH ASSEMBLY DISCONNECT THE
WIRES FROM THE BACK OF THE SWITCH.
2.4 REPLACE WITH NEW SWITCH, CHECK WIRING AS PER WIRING
DIAGRAM, AND THAT SWITCHES ARE IN THE CORRECT POSITION.
2.5 REASSEMBLE SWITCH ASSEMVLE AND BRACKET IN REVERSE TO
PROCEDURE ABOVE
2.6 TEST TO ELECTRICAL SAFETY STANDARDS.

RGT - SERIES
APPROVED Page 5 of 6
ISSUE: C
ECN 07 033
SECTION 3.
POWER CORD REPLACEMENT
3.1 REMOVE MOTOR HOUSING AS PER THE INSTRUCTIONS IN
SECTION 1
3.2 REMOVE THE TOP COVER (3 SCREWS).
3.3 REMOVE THE CABLES FROM THE CONNECTOR BLOCK .
3.4 PULL OUT POWER CORD AND RECONNECT NEW CORD.
3.5 CARRY OUT EARTH TEST BEFORE CONNECTING TO POWER
3.6 REPLACE IN REVERSE ORDER AS ABOVE
3.7 TEST TO ELECTRICAL SAFETY STANDARDS