Roche cobas h232 User manual

cobas h 232
Supplement to the Operator's Manual V6.0

2
Purpose of document
This document provides a description of changes to the Operator’s Manual version 6.0 for
SW 04.01.xx. This supplement is valid for and intended to be used in conjunction with the
cobas h 232 Operator’s Manual version 6.0. It is not a replacement for the complete
cobas h 232 Operator’s Manual version 6.0. Changes or additions to the information in the
cobas h 232 Operator’s Manual version 6.0 are shown in colour.
© 2019 Roche Diagnostics GmbH
The contents of this document, including all graphics, are the property of Roche Diagnostics. No
part of this document may be reproduced or transmitted in any form or by any means, electronic
or mechanical, for any purpose, without the express written permission of Roche Diagnostics.
Roche Diagnostics has made every reasonable effort to ensure that all the information contained
in this supplement is correct at the time of printing. However, Roche Diagnostics reserves the
right to make any changes necessary without notice as part of ongoing product development.
Please send questions or comments about this document to your local Roche representative.
ROCHE CARDIAC, COBAS, COBAS H and IQC are trademarks of Roche.
Document version Date Content
1.0 2019-06 New Document, created as an amendment to
Operator's Manual Version 6.0
Be sure to read the complete cobas h 232 Operator’s Manual version 6.0.
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.

Table of Contents
3
What is new in SW 04.01.xx 5
Functions introduced with SW 04.01.xx ...................................................................................................... 5
Result memory .................................................................................................................................... 5
Diagnostics........................................................................................................................................... 6
Amendments to Operator’s Manual version 6.0 7
Revised sections................................................................................................................................................... 7
Symbols.................................................................................................................................................. 7
Battery pack ......................................................................................................................................... 8
Power supply........................................................................................................................................ 8
2.1 Installing or replacing the battery pack.............................................................................. 9
Removing the battery pack ............................................................................................................ 9
Shut down / restart meter............................................................................................................. 10
Automatic shutdown....................................................................................................................... 10

Table of Contents
4
This page intentionally left blank.

5
EN
What is new in SW 04.01.xx
Functions introduced with SW 04.01.xx
Result memory
The following information has been added to page 71 with SW 04.01.xx:
Result memory settings allow to apply a Result Display Filter, to set the Result Storage Mode (see
page 73), and to delete stored test results and code chip data (see page 74).
The following information has been added to page 74 with SW 04.01.xx:
10 From the Setup-Result Memory menu,
touch Result/Code Chip Deletion to
delete stored test results and code chip
data.
11 Touch to delete all data, or touch
to exit this screen without deleting any
data. The display automatically returns to
the previous screen.
12 Touch to return to the Setup-Data
Handling menu.
Result Storage Mode
Result Display Filter
Setup - Result Memory
04/19/2016
Result/Code Chip Deletion
Confirm Deletion
Do you really want to delete
all result and code chip data?
04/19/2016

6
Diagnostics
The following information has been added on page 81 with SW 04.01.xx:
13 From the Diagnostics menu, touch the
button of the diagnostics screen you want
to display.
14 Use and to toggle between the
Wireless Setup screens.
15 In either diagnostics screen, touch to
return to the Diagnostics menu.
Note: The Wireless Setup button is only
available if the meter is equipped with WLAN
functionality.
Use DNS:
Use DHCP:
Enabled
Disabled
SSID:
cobas h 232
WLAN:
01 23 45 67 89 AB
Wireless Setup - Network
Wireless Setup
MAC:
04/19/2016
Error History
Wireless Setup
Diagnostics
Software
04/19/2016
Software
Build:
Boot:
MM-FW:
MM-BL:
App:
RootFS:
Kernel:
04.00.00
06.03.00
03.00.00
03.00.00
04.00.00
06.03.00
06.03.00
04/19/2016
DMS Port Number:
DMS Name:
POCTServer
4711
DMS IP Address:
0.0.0.0
RF Security:
WPA2-PSK (AES)
Wireless Setup - Connection
Wireless Setup
04/19/2016
Test
Authenticated:
RF activated:
Associated:
Configured IP:
IP:
Subnet:
Gateway:
DNS:
Contacted DMS:
Connected to DMS:
Completed:
255.255.255.0
Wireless Setup - Test
Wireless Setup
192.168.0.123
04/19/2016
Error History
b360401c - 205
02/10/16 08:00
b360401c - 205
03/12/16 08:30
b5804001 - 302
01/02/16 10:17
b5804001 - 302
11/14/15 07:30
b360401c - 205
10/10/15 07:05
04/19/2016

7
EN
Amendments to Operator’s Manual version 6.0
Revised sections
Symbols
The following information has been added or changed on page 5:
Caution, consult accompanying documents. Refer to safety-related notes in the
instructions for use accompanying this instrument.
Temperature limitation (Store at)
Manufacturer
Date of manufacture
Batch code/ Lot number
Catalogue number
Global Trade Item Number
Serial Number
In vitro diagnostic medical device
This product fulfills the requirements of the European Directives 98/79/EC on
in vitro diagnostic medical devices and 2014/53/EU on the harmonisation of the
laws of the Member States relating to the making available on the market of radio
equipment.
The system fulfills the Canadian and U.S. safety requirements (UL LISTED, in
accordance with UL 61010A-1:02 and CAN/CSA-C22.2 No. 61010-1-04).
LOT
SN
IVD

8
Battery pack
The following information has been added or changed on page 17:
The meter contains a rechargeable battery pack that can be charged if the power adapter is con-
nected or the meter is placed on an active Handheld Base Unit (i.e., one connected to a power
adapter). The charging process starts as soon as the meter goes into standby mode.
Power supply
The following information has been added on page 40:
The meter can be operated with the rechargeable battery pack only or together with the power
adapter or the (optional) Handheld Base Unit, which both can charge the battery pack when
inserted.

9
EN
2.1 Installing or replacing the battery pack
The following information has been added or changed on page 36:
Removing the battery pack
The following information has been changed on page 37:
When shipped, the battery pack is not installed in the meter. When the battery pack is not
installed, the meter cannot be used.
Unused battery packs lose their charge over time and have to be recharged before they can
be used. After installing a new battery pack, the meter should be charged at least 4 hours
before testing, preferably overnight.
Whenever the meter is placed on an active Handheld Base Unit or powered by the power
adapter, the icon is displayed. This icon shows that power is available and the meter
can be charged if necessary. To start the charging process immediately put the meter into
standby mode by pressing the On/Off button for approximately 1 second.
Make sure that the permitted temperature range for charging the battery pack (12-32 °C or
54-90 °F) is maintained during installation and initial setup.
Replace the battery pack within approximately 24 hours to retain the date and time settings.
Beyond this period of time, you may have to re-enter date and time. Replace the battery
pack only in shutdown mode, see page 41.
1If a battery pack is already installed, make
sure that the meter is shut down to pre-
vent damage to the meter or potential
data loss (see page 41).

10
The following information has been added on page 41:
Shut down / restart meter
Shutting down the meter shuts down wireless communication and all other functionalities. Date
and time, however, are maintained.
1 Device is not connected to the external power supply or HBU:
To shut down the meter, press the button for about 5 seconds and release the button as soon
as the Roche logo is displayed and the meter beeps. The screen goes blank and the meter is shut
down.
Use meter shutdown when you want to remove or replace the battery pack (see page 36).
2 Device is connected to the external power supply or HBU:
To restart the meter, press the button for about 5 seconds and release the button as soon as
the Roche logo is displayed and the meter beeps. The screen goes blank and the meter powers
itself off and on.
Use meter restart if the meter does not respond to user actions (like touching buttons).
Automatic shutdown
If the battery pack is critically low, the meter willl shut down automatically.
If you press the button for too long, a meter reset will be triggered after about 12 seconds
(see page 182) and date and time will be lost.

11

0 8984123001 (01) 2019-06 EN
ROCHE CARDIAC, COBAS, COBAS H
and IQC are trademarks of Roche.
Roche Diagnostics GmbH
Sandhofer Strasse 116
68305 Mannheim, Germany
www.roche.com
www.cobas.com
www.poc.roche.com