Rockler Dust Right 53212 User manual

PLEASE SEE OTHER SIDE FOR IMPORTANT SAFETY WARNINGS
Fig. 1
1. Assemble the Straps as shown in Fig. 1.
2. Thread a Nut and Washer onto the post of each
Adjustable Foot and thread each Adjustable Foot into
the Body. Fig. 2. You will finalize the position of these
and tighten them later.
3. Buckle and lay out the Straps so that the strap adjusters
will face out when the Straps are installed.
4. Insert a Strap Pin in the loop at one end of one of the
Straps and then insert the Strap Pin in the round slot in
the Body, again making sure that the Strap Adjusters
will face out when the Straps are installed. Feed the
Strap into the slot and push down on the Strap Pin
until it snaps into place. Fig. 3.
5. Insert a Strap Pin in the loop at the other end of the
Strap and then insert the Strap Pin in the round slot at
the other end on the same side of the Body and snap
it into place. Fig. 3.
6. Repeat Steps 4 and 5 for the other Strap on the other
side of the Body.
7. Unbuckle the Strap on the side opposite the Adjustable
Feet and fit the Strap around your Dust Right®
Separator (45556, sold separately). Buckle and adjust
the Strap to achieve a snug fit. The Straps can be
adjusted up and down along the Strap Pins if needed.
8. Unbuckle the other Strap and position your shop
vacuum against the Adjustable Feet. Thread the
Adjustable Feet in or out as needed to provide stable
contact with your shop vacuum. Tighten the Nuts.
Check Rockler.com for updates. If you have further questions, please
contact our Technical Support Department at 1-800-260-9663
or [e-mail]
9. Buckle and adjust the Strap around your shop vacuum
to achieve a snug fit.
Fig. 2
Fig. 3
Nut
Adjustable
Foot
Washer
Strap Pin
Strap Loop
Strap Loop
Vacuum Harness Assembly Instructions

Distributed by Rockler Companies, Inc.
Medina, Mn 55340
57896
Rev 10/17
BP0617
This product is designed for specific applications as defined in the instructions and should not be modified and/or
used for any other applications. Before using the Vacuum Harness, read, understand and follow all instructions and
safety information provided. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY WARNINGS
>Always confirm that you are using the most recent
version of the Instructions and safety warnings for
your product. To find the most recent version, find
the product page on Rockler.com and click on the
link to the Instructions.
>For any tool used in conjunction with this product,
always read, understand and follow the instructions
 andsafetywarningsintheowner’smanualforthattool.
 Ifyoudonothavetheowner’smanual,obtainonefrom
 thetool’smanufacturerbeforeusingitwiththisproduct.
>Before using this product, review and verify that all
tools to be used with it have safety equipment
installed and are in proper working order as
 definedbythetools’owner’smanuals.
>Do not use this product until you have read and
are confident you understand the instructions.
>Do not use this product in any manner other than
what is described in these instructions. Use only
recommended accessories.
>Remain alert and use good judgment when using
this tool. Do not use this tool if you are in any way
impaired by medications, alcohol, drugs or fatigue.
>Dress appropriately and remove all jewelry, secure
loose clothing and tie up long hair before using
this tool.
>It is the sole responsibility of the purchaser of this
product to ensure that any third party whom you
allow to use this product reads and complies with all the
instructions and safety precautions outlined in this
manual prior to use.
>Maintain these instructions and warnings as long as
you own the product. Keep this booklet in a place where
it will be readily available for reference.
>The user assumes all risk and responsibility for the
proper use of this product and for ensuring product
suitability for intended application.
>Always wear safety glasses in compliance with ANSI
safety standards and hearing protection and follow all
standard shop safety practices, including:
•Keep your work area well lit and clean;
• Unplug all power tools before making any
adjustments or changing accessories;
•Use dust collection tools and dust face masks to
reduce exposure to dust;
•Use accessory safety equipment such as
featherboards, push sticks and push blocks
whenever appropriate;
•Do not use power tools in explosive
environments (e.g., in the presence of
flammable liquids, fumes or dust);
•Keep children and bystanders away from
the tool operating area;
•Maintain proper footing at all times and
do not overreach;
•Do not force the tool.
>These warnings and instructions do not represent the
total of all information available regarding tool safety,
use and technique. Please read the full manual before
using this product and always seek out opportunities to
learn more and improve your skills and knowledge.
Drilling, sawing, sanding or machining
wood products can expose you to wood dust, a
substance known ot the State of California to cause
cancer. Avoid inhaling wood dust or use a dust mask
or other safeguards for personal protection. For more
information go to www.P65Warnings.ca.gov/wood.
Danger indicates a hazardous situation that, if not avoided, will result in death or serious injury.
Warning indicates a hazardous situation that, if not avoided, could result in death or serious injury.
Caution indicates a hazardous situation that, if not avoided, may result in minor or moderate injury
or property damage.
Notice indicates important or helpful information and/or user tips.