Rockwell Automation Allen-Bradley Micro800 User manual

Quick Start
Micro800 Controllers Starter Pack
Controller Catalog Numbers 2080-LC10, 2080-LC20, 2080-L50E
Starter Pack Catalog Numbers 2080-LC10-STARTERPACK,
2080-LC20-STARTERPACK, 2080-LC20-STARTERPACKL,
2080-LC50-STARTERPACK, 2080-LC50-STARTERPACKL
Original Instructions

2Rockwell Automation Publication 2080-QS004C-EN-E - October 2023
Micro800 Controllers Starter Pack Quick Start
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this
equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and
wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried
out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application
of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements
associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the
examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in
this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Labels may also be on or inside the equipment to provide specific precautions.
The following icon may appear in the text of this document.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT Identifies information that is critical for successful application and understanding of the product.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
Identifies information that is useful and can help to make a process easier to do or easier to understand.

Rockwell Automation Publication 2080-QS004C-EN-E - October 2023 3
Table of Contents
Preface
About This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Download Firmware, AOP, EDS, and Other Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Where to Start
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 1
Study Guide Overview What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Start Connected Components Workbench Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connected Components Workbench Software Design Environment . . . . . . . . . . . 11
Project Organizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Workspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Toolbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 2
Hands-on Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 3
Create and Save a Connected
Components Workbench Project
Create a Connected Components Workbench Project. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Save Your Connected Components Workbench Project . . . . . . . . . . . . . . . . . . . . . . . . . 23
Chapter 4
Build and Download Project Build and Download the Project to your Micro800 Controller . . . . . . . . . . . . . . . . . . . . . 25
Chapter 5
Connect the Input Simulator
Board
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 6
Monitor Your Micro800
Controller Program
Monitor Your Program in Connected Components Workbench Software . . . . . . . . . . . 31
View Real-time Changes in List Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Chapter 7
How to Create Variables Create Local Variables for your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

4Rockwell Automation Publication 2080-QS004C-EN-E - October 2023
Table of Contents
Chapter 8
How to Implement an
Instruction Block
Add a TON Instruction Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Enter Parameters for TON Instruction Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Add an ANY_TO_TIME Instruction Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 9
How to Add a Plug-in Module Add a Plug-in Module to the Micro800 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Chapter 10
Learn About User-defined
Functions and User-defined
Function Blocks
Create a UDF for your Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Add the UDF to your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Get Sample Code from the Rockwell Automation Sample Code Library. . . . . . . . . . . . . 53
Import Sample Code into Your Project. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Chapter 11
Import and Export Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Chapter 12
Quick Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 13
PanelView 800 Graphic Terminal
Design in Connected
Components Workbench
Software
Add a PanelView 800 Terminal to Your Project. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Configure Your PanelView 800 Terminal Communication Settings . . . . . . . . . . . . . . . . 64
Chapter 14
Using HMI Tags Create Global Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Edit Ladder Diagram Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Chapter 15
Configure Micro800 Controller
Ethernet Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Chapter 16
HMI Tag Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Chapter 17
HMI Screen Create a Screen for Your PanelView 800 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Create Objects for Your Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Chapter 18
Configure PanelView 800
Terminal Ethernet Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Rockwell Automation Publication 2080-QS004C-EN-E - October 2023 5
Table of Contents
Chapter 19
Download HMI Application Save and Download Project. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Chapter 20
Test the HMI Application Run the HMI Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Test the HMI application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Appendix A
Set Up Serial Communication
Between Computer and
Micro820 Controller
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Connect the Computer to the Micro820 Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Configure RSLinx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Restore Serial Port to Factory Default Setting Using a microSD Card . . . . . . . . . . . . . 103

6Rockwell Automation Publication 2080-QS004C-EN-E - October 2023
Table of Contents
Notes:

Rockwell Automation Publication 2080-QS004C-EN-E - October 2023 7
Preface
About This Publication
Use this quick start to learn how to use the Micro800™ controller, a PanelView™ 800 graphic terminal, and Connected Components
Workbench™ software.
Download Firmware, AOP, EDS, and Other Files
Download firmware, associated files (such as AOP, EDS, and DTM), and access product release notes from the Product Compatibility and
Download Center at rok.auto/pcdc.
Summary of Changes
This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect
all changes.
Additional Resources
These documents contain additional information concerning related products from Rockwell Automation. You can view or download
publications at rok.auto/literature.
Topic Page
Updated template throughout
Updated minimum Micro800 controller firmware revision 11, 17
Updated minimum Connected Components Workbench software version 11
Updated step in Create a Connected Components Workbench Project 18
Updated steps in Create the Ladder Diagram program 20, 21, 22
Added tip to Monitor Your Program in Connected Components Workbench Software 31
Updated step in Monitor Your Program in Connected Components Workbench Software 31
Updated steps in Add a TON Instruction Block 37, 38
Updated step in Enter Parameters for TON Instruction Block 39
Updated steps in Add an ANY_TO_TIME Instruction Block 40, 41
Updated step in Add a Plug-in Module to the Micro800 Controller 47
Updated step in Add the UDF to your Program 51
Updated Quick Tips table 61
Updated step in Configure Your PanelView 800 Terminal Communication Settings 66
Updated steps in Create Global Variables 69
Updated steps in HMI Tag Editor 75
Updated step in Restore Serial Port to Factory Default Setting Using a microSD Card 104
Additional Resources
Resource Description
Micro800 Controllers Starter Pack Quick Reference, publication 2080-QR003 Provides information for setting up the Micro800 controllers and input simulator boards.
Micro800 Programmable Controller Family Selection Guide,
publication 2080-SG001 Provides information to help you select the Micro800 controller, plug-ins, expansion I/O, and
accessories, based on your requirements.
Micro800 Programmable Controllers Technical Data, publication 2080-TD001 Provides detailed specifications for Micro800 controllers, expansion I/O modules, plug-in
modules, and accessories.
Micro810 Programmable Controllers User Manual, publication 2080-UM001 Describes how to install, configure, use, and troubleshoot your Micro810® controller.
Micro820 Programmable Controllers User Manual, publication 2080-UM005 Describes how to install, configure, use, and troubleshoot your Micro820 controller.
Micro830, Micro850, and Micro870 Programmable Controllers User Manual,
publication 2080-UM002 Describes how to install, configure, use, and troubleshoot your Micro830®, Micro850, and
Micro870® controllers.
Micro800 Expansion I/O Modules User Manual, publication 2080-UM003 Describes how to install, configure, use, and troubleshoot your Micro800 expansion I/O
modules

8Rockwell Automation Publication 2080-QS004C-EN-E - October 2023
Preface
Micro800 Plug-in Modules User Manual, publication 2080-UM004 Describes how to install, configure, use, and troubleshoot your Micro800 plug-in modules.
Micro800 Programmable Controllers General Instructions Reference Manual,
publication 2080-RM001 Provides reference information about the instruction set available for developing programs
for use in Micro800 control systems.
PanelView 800 HMI Terminals User Manual, publication 2711R-UM001 Provides information on how to configure, use, and troubleshoot your PanelView 800 HMI
terminal.
EtherNet/IP Network Devices User Manual, publication ENET-UM006 Describes how to configure and use EtherNet/IP™ devices to communicate on the
EtherNet/IP network.
Ethernet Reference Manual, publication ENET-RM002 Describes basic Ethernet concepts, infrastructure components, and infrastructure features.
System Security Design Guidelines Reference Manual,
publication SECURE-RM001
Provides guidance on how to conduct security assessments, implement Rockwell
Automation products in a secure system, harden the control system, manage user access,
and dispose of equipment.
Industrial Components Preventive Maintenance, Enclosures, and Contact
Ratings Specifications, publication IC-TD002 Provides a quick reference tool for Allen-Bradley industrial automation controls and assemblies.
Safety Guidelines for the Application, Installation, and Maintenance of
Solid-state Control, publication SGI-1.1
Designed to harmonize with NEMA Standards Publication No. ICS 1.1-1987 and provides
general guidelines for the application, installation, and maintenance of solid-state control in
the form of individual devices or packaged assemblies incorporating solid-state
components.
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.
Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and other certification details.
Additional Resources (Continued)
Resource Description

Rockwell Automation Publication 2080-QS004C-EN-E - October 2023 9
Where to Start
Follow this workflow to learn how to use the Connected Components Workbench software with your Micro800 controllers and
PanelView 800 terminals.
Chapter 1
Study Guide Overview
Chapter 2
Hands-on Content
Chapter 3
Create and Save a Connected
Components Workbench Project
Chapter 4
Build and Download Project
Chapter 5
Connect the Input Simulator Board
Chapter 6
Monitor Your Micro800 Controller Program
Chapter 7
How to Create Variables
Chapter 8
How to Implement an Instruction Block
Chapter 9
How to Add a Plug-in Module
Chapter 10
Learn About User-defined Functions
and User-defined Function Blocks
Chapter 11
Import and Export Project
Chapter 12
Quick Tips
Chapter 13
PanelView 800 Graphic Terminal Design
in Connected Components Workbench
Software
Chapter 14
Using HMI Tags
Chapter 15
Configure Micro800 Controller
Ethernet Settings
Chapter 16
HMI Tag Editor
Chapter 17
HMI Screen
Chapter 18
Configure PanelView 800 Terminal
Ethernet Settings
Chapter 19
Download HMI Application
Chapter 20
Test the HMI Application

10 Rockwell Automation Publication 2080-QS004C-EN-E - October 2023
Where to Start
Notes: