Rohde & Schwarz SMB100B User manual

R&S®SMB100B
RF Signal Generator
Getting Started
1422104502
Version 06
(>F:]2)

This document describes the R&S®SMB100B, stock no. 1422.1000.02 and its
options.
© 2023 Rohde & Schwarz GmbH & Co. KG
Muehldorfstr. 15, 81671 Muenchen, Germany
Phone: [phone] - 0
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
All other trademarks are the properties of their respective owners.
1422.1045.02 | Version 06 | R&S®SMB100B
The following abbreviations are used throughout this manual: R&S®SMB100B is abbreviated as
R&S SMB100B, R&S®VISA is abbreviated as R&S VISA

Contents
R&S®SMB100B
3Getting Started 1422.1045.02 ─ 06
Contents
1 Safety and regulatory information....................................... 7
1.1 Safety instructions................................................................................7
1.2 Labels on R&S SMB100B................................................................... 10
1.3 Warning messages in the documentation........................................ 11
1.4 Where to find key documents on Rohde & Schwarz....................... 11
1.5 Korea certification class B.................................................................12
2 Documentation overview.................................................... 13
2.1 Getting started manual.......................................................................13
2.2 User manuals and help.......................................................................13
2.3 Service manual....................................................................................13
2.4 Instrument security procedures........................................................ 14
2.5 Printed safety instructions.................................................................14
2.6 Data sheets and brochures................................................................14
2.7 Release notes and open source acknowledgment (OSA)...............14
2.8 Application notes, application cards, white papers, etc................. 15
2.9 Videos.................................................................................................. 15
3 Key features......................................................................... 17
4 Preparing for use................................................................. 19
4.1 Lifting and carrying............................................................................ 19
4.2 Unpacking and checking....................................................................19
4.3 Choosing the operating site.............................................................. 20
4.4 Setting up the R&S SMB100B............................................................20
4.4.1 Placing the R&S SMB100B on a bench top..........................................20
4.4.2 Mounting the R&S SMB100B in a rack................................................. 22

Contents
R&S®SMB100B
4Getting Started 1422.1045.02 ─ 06
4.5 Considerations for test setup............................................................ 23
4.6 Connecting to power.......................................................................... 24
4.7 Connecting to LAN............................................................................. 24
4.8 Connecting USB devices................................................................... 25
4.9 Connecting to RF coaxial connectors.............................................. 26
4.10 Connecting to RF 50 Ω....................................................................... 28
4.11 Connecting to Ref In/Ref Out.............................................................28
4.12 Switching on or off............................................................................. 29
5 Instrument tour.................................................................... 31
5.1 Front panel tour.................................................................................. 31
5.1.1 Utility keys.............................................................................................32
5.1.2 Touchscreen..........................................................................................32
5.1.3 Function keys........................................................................................33
5.1.4 Navigation controls............................................................................... 33
5.1.4.1 Rotary knob...........................................................................................33
5.1.4.2 Editing keys...........................................................................................34
5.1.4.3 Navigation keys.....................................................................................34
5.1.5 Display keys..........................................................................................35
5.1.6 USB connector......................................................................................35
5.1.7 RF 50 Ω.................................................................................................36
5.1.8 Keypad..................................................................................................36
5.1.9 On/Standby........................................................................................... 36
5.2 Rear panel tour....................................................................................36
5.2.1 Connectors............................................................................................37
6 Trying out the instrument................................................... 41
6.1 Generating an unmodulated carrier.................................................. 41
6.2 Generating an RF frequency sweep signal...................................... 45

Contents
R&S®SMB100B
5Getting Started 1422.1045.02 ─ 06
6.3 Saving and recalling settings............................................................ 47
7 Instrument control............................................................... 51
7.1 Possible ways to operate the instrument......................................... 51
7.2 Means of manual interaction............................................................. 52
7.3 Understanding the display information............................................ 52
7.3.1 Status bar..............................................................................................53
7.3.2 Tile diagram.......................................................................................... 53
7.3.3 Taskbar................................................................................................. 54
7.3.4 Additional display characteristics.......................................................... 55
7.4 Accessing the functionality............................................................... 56
7.5 Entering data....................................................................................... 57
7.5.1 Entering numeric parameters................................................................58
7.5.2 Entering alphanumeric parameters.......................................................59
7.5.3 Undo and redo actions..........................................................................59
7.6 Getting information and help.............................................................59
7.7 Remote control....................................................................................61
7.8 Remote operation over VNC.............................................................. 62
8 Contacting customer support............................................ 63
Index..................................................................................... 65

Contents
R&S®SMB100B
6Getting Started 1422.1045.02 ─ 06

Safety and regulatory information
R&S®SMB100B
7Getting Started 1422.1045.02 ─ 06
1 Safety and regulatory information
The product documentation helps you use the product safely and efficiently. Fol-
low the instructions provided here and in the following chapters.
Intended use
The product generates radio frequency (RF) signals for the development, produc-
tion and verification of electronic components, modules or devices. The product is
intended for industrial use, for example for production and conformance testing,
maintenance and engineering laboratories.
Use the product only for its designated purpose. Any other use is considered
improper use. Observe the operating conditions and performance limits stated in
the data sheet.
Target audience
This document targets at all users, including technicians, operators, administra-
tors and maintenance personnel. The required skills and experience of the users
depend on the test setup and application of the product.
Where do I find safety information?
Safety information is part of the product documentation. It warns you of potential
dangers and gives instructions on how to prevent personal injury or damage
caused by dangerous situations. Safety information is provided as follows:
●In Chapter 1.1, "Safety instructions", on page 7. The same information is
provided in many languages as printed "Safety Instructions". The printed
"Safety Instructions" are delivered with the product.
●Throughout the documentation, safety instructions are provided when you
need to take care during setup or operation.
1.1 Safety instructions
Products from the Rohde & Schwarz group of companies are manufactured
according to the highest technical standards. To use the products safely, follow
the instructions provided here and in the product documentation. Keep the prod-
uct documentation nearby and offer it to other users.
Safety instructions

Safety and regulatory information
R&S®SMB100B
8Getting Started 1422.1045.02 ─ 06
Use the product only for its intended use and within its performance limits. Inten-
ded use and limits are described in the product documentation such as the data
sheet, manuals and the printed "Safety Instructions". If you are unsure about the
appropriate use, contact Rohde & Schwarz customer service.
Using the product requires specialists or specially trained personnel. These users
also need sound knowledge of at least one of the languages in which the user
interfaces and the product documentation are available.
Reconfigure or adjust the product only as described in the product documentation
or the data sheet. Any other modifications can affect safety and are not permitted.
Never open the casing of the product. Only service personnel authorized by
Rohde & Schwarz are allowed to repair the product. If any part of the product is
damaged or broken, stop using the product. Contact Rohde & Schwarz customer
service at https://www.rohde-schwarz.com/support.
Lifting and carrying the product
The maximum weight of the product is provided in the data sheet. You can lift or
carry the product by yourself, if you can manage the weight on your own. Alterna-
tively, you can use lifting or transporting equipment. Follow the instructions provi-
ded by the equipment manufacturer.
Choosing the operating site
Only use the product indoors. The product casing is not waterproof. Water that
enters can electrically connect the casing with live parts, which can lead to elec-
tric shock, serious personal injury or death if you touch the casing. If
Rohde & Schwarz provides accessories designed for your product, e.g. a carrying
bag, you can use the product outdoors.
Unless otherwise specified, you can operate the product up to an altitude of
2000 m above sea level. The product is suitable for pollution degree 2 environ-
ments where nonconductive contamination can occur. For more information on
environmental conditions such as ambient temperature and humidity, see the
data sheet.
Setting up the product
Always place the product on a stable, flat and level surface with the bottom of the
product facing down. If the product is designed for different positions, secure the
product so that it cannot fall over.
Safety instructions

Safety and regulatory information
R&S®SMB100B
9Getting Started 1422.1045.02 ─ 06
If the product has foldable feet, always fold the feet completely in or out to ensure
stability. The feet can collapse if they are not folded out completely or if the prod-
uct is moved without lifting it. The foldable feet are designed to carry the weight of
the product, but not an extra load.
If stacking is possible, keep in mind that a stack of products can fall over and
cause injury.
If you mount products in a rack, ensure that the rack has sufficient load capacity
and stability. Observe the specifications of the rack manufacturer. Always install
the products from the bottom shelf to the top shelf so that the rack stands
securely. Secure the product so that it cannot fall off the rack.
Connecting to power
The product is an overvoltage category II product. Connect the product to a fixed
installation used to supply energy-consuming equipment such as household
appliances and similar loads. Keep in mind that electrically powered products
have risks, such as electric shock, fire, personal injury or even death. Replace
parts that are relevant to safety only by original parts, e.g. power cables or fuses.
Take the following measures for your safety:
●Before switching on the product, ensure that the voltage and frequency indica-
ted on the product match the available power source. If the power adapter
does not adjust automatically, set the correct value and check the rating of the
fuse.
●Only use the power cable delivered with the product. It complies with country-
specific safety requirements. Only insert the plug into an outlet with protective
conductor terminal.
●Only use intact cables and route them carefully so that they cannot be dam-
aged. Check the power cables regularly to ensure that they are undamaged.
Also ensure that nobody can trip over loose cables.
●If you connect the product to an external power supply, use the one delivered
with the product or recommended in the product documentation. The external
power supply must conform to the country-specific regulations.
●Only connect the product to a power source with a fuse protection of maxi-
mum 20 A.
●Ensure that you can disconnect the product from the power source at any
time. Pull the power plug to disconnect the product. The power plug must be
easily accessible. If the product is integrated into a system that does not meet
Safety instructions

Safety and regulatory information
R&S®SMB100B
10Getting Started 1422.1045.02 ─ 06
these requirements, provide an easily accessible circuit breaker at the system
level.
Cleaning the product
Use a dry, lint-free cloth to clean the product. When cleaning, keep in mind that
the casing is not waterproof. Do not use liquid cleaning agents.
Meaning of safety labels
Safety labels on the product warn against potential hazards.
Potential hazard
Read the product documentation to avoid personal injury or product damage.
Electrical hazard
Indicates live parts. Risk of electric shock, fire, personal injury or even death.
Hot surface
Do not touch. Risk of skin burns. Risk of fire.
Protective conductor terminal
Connect this terminal to a grounded external conductor or to protective ground. This
connection protects you against electric shock if an electric problem occurs.
1.2 Labels on R&S SMB100B
Labels on the casing inform about:
●Personal safety, see "Connecting to power" on page 9.
●Product and environment safety, see Table 1-1.
●Identification of the product, see the serial number on the rear panel.
Table 1-1: Labels regarding R&S SMB100B and environment safety
Labeling in line with EN 50419 for disposal of electrical and electronic equipment after
the product has come to the end of its service life. For more information, see the prod-
uct user manual, chapter "Disposal".
Labels on R&S SMB100B