Rohnson R-7500 NEXT GEN User manual

Digital Touch Control Kettle R-7500 NEXT GEN
EN
1
Instructions Manual
Digital Touch-Control Kettle
R-7500 NEXT GEN
CONGRATULATIONS ON PURCHASING DIGITAL TOUCH-CONTROL
KETTLE

Digital Touch Control Kettle R-7500 NEXT GEN
EN
2
PLEASE READ THIS USER GUIDE CAREFULLY BEFORE OPERATING
YOUR DIGITAL TOUCH CONTROLKETTLE AND KEEP IT FOR FUTURE
REFERENCE FOR HOME USE ONLY NOT FOR COMMERCIAL USE.
SAFETY PRECAUTIONS
When using any electrical appliance, basic safety precautions
should always be followed including the following:
•Please read the instructions carefully before using any appliance.
•Always ensure that the voltage on the rating label correspond, to the mains
voltage in your home.
•Incorrect operation and improper use can damage the appliance and cause
injury to the user
•The appliance is intended for household use only and is not user-serviceable.
Commercial use invalidates the guarantee and the supplier cannot be held
responsible for injury or damage caused when using the appliance for any
other purpose than that intended
•This appliance is intended to be used in household and similar applications
such as:
-Staff kitchen areas in shops, offices and other working environments
-Farm houses
-By clients in hotels, motels and other residential type environments
-Bed and breakfast type environments
•Avoid any contact with moving parts
•Keep the kettle safely out of reach of children. Close supervision is necessary
when this appliance is used by or near children
•This appliance is not intended for use by persons (including children)with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety
•Children should be supervised to ensure that they do not play with the
appliance

Digital Touch Control Kettle R-7500 NEXT GEN
EN
3
•Check the power cord and plug regularly for any damage. If the cord or the
plug is damaged, it must be replaced by the manufacturer or a qualified
person in order to avoid an electrical hazard
•Do not use the appliance if it has been dropped or damaged in any way. In
case of damage, take the unit in for examination and/or repair by an
authorized service agent
•Do not open the lid while the kettle is in use
•Do not fill the kettle above the MAX level(1.5L). Boiling water may splash out
if overfilled
•Unplug from outlet when not in use and before cleaning. Allow it to cool down
completely before cleaning the appliance
•Do not insert any objects into holes or slots in this appliance
•To reduce the risk of electric shock, do not immerse or expose the element
assembly, base assembly, plug or the power cord lo water or any other liquid
•Never immerse the unit in water or any other liquid for cleaning purposes. Do
not allow liquid to penetrate into the electrical parts of this kettle
•Remove the plug from the socket by gripping the plug. Do not pull on the cord
to disconnect the appliance from the mains. Always unplug the unit when not
in use, before cleaning or when adding or removing parts
•The use of accessory attachments that are not recommended or supplied by
the manufacturer may result in injuries, fire or electric shock. The kettle is only
to be used with the base provided
•A short cord is provided to reduce the hazards resulting from becoming
entangled in or tripping over a longer cord
•Do not let the cord hang over the edge of a table or counter. Ensure that the
cord is not in a position where it can be pulled on inadvertently
•Do not allow the cord to touch hot surfaces and do not place on or near a hot
gas or electric burner or in a heated oven
•Do not use the appliance on a gas or electric cooking top or over or near an
open flame
•Keep the appliance and the cord away from heat, direct sunlight, moisture and
sharp edges

Digital Touch Control Kettle R-7500 NEXT GEN
EN
4
•Do not place the kettle or its base on a wet surface or into any liquid. Do not
operate it with wet hands Should the kettle become wet, unplug the cord from
the wall and dry the kettle thoroughly with a cloth
•Cleaning and user maintenance shall not be made by children
•Keep the appliance and its cord out of reach of children
•Use of an extension cord with this appliance is not recommended. However, if
it is necessary to use an extension lead, ensure that the lead is suited to the
power consumption of the appliance to avoid overheating of the extension
cord, appliance or plug point. Remember to not place the extension cord in a
position where it can be pulled on by children or animals or tripped over
•This appliance is not suitable for outdoor use. Do not use this appliance for
anything other than its intended use
•Do not carry the appliance by the power cord
•Do not leave the appliance unattended during use. Always unplug the unit
when not in use or before cleaning,and allow it to cool down completely
before cleaning
•Always operate the appliance on a smooth, even, stable surface. Do not place
the unit on a hot surface
•Ensure that the kettle has entered standby mode alter each use
•The manufacturer does not accept responsibility for any damage or injury
caused by improper or incorrect use,or for repairs carried out by unauthorized
personnel
•In case of technical problems, switch off the machine and do not attempt to
repair it yourself. Return the appliance to an authorized service facility for
examination, adjustment or repair. Always insist on the use of original spare
parts. Failure to comply with the above mentioned precautions and
instructions, could affect the safe operation of this machine
•We recommend using cool or room temperature water, instead of cold water,
to prolong the life of your appliance
•Do not touch hot surfaces. Use the handle and lid release button
•Take care when pouring-pour slowly, and don' t over-tilt the kettle
•Check the lid is fully closed before switching the kettle on, otherwise it may
not switch off
•Check the kettle is properly located on the base before switching on

Digital Touch Control Kettle R-7500 NEXT GEN
EN
5
•Do not switch on unless the kettle contains at least 2 cups of water
•Remove the kettle from its base before filing or pouring
•When opening the lid after boiling, position the id so that steam is directed
away from the handle and safely away from sensitive areas such as your
face, hands and arms to prevent burns
•This appliance must not be operated by an external timer or remote control
system
•Please be careful when using this appliance at elevations of over 2500 meters
above sea level. At this elevation or altitude, the appliance will continue to boil
water and splash from the lid and spout
DIGITAL TOUCH CONTROL KETTLE OVERVIEW
1. Lid
2. Spout
3. Body
4. Lid release button
5. Safety handle
6. Touch-control buttons
7. Base with plug

Digital Touch Control Kettle R-7500 NEXT GEN
EN
6
GETTING STARTED
Remove all packaging from the DIGITAL TOUCH CONTROL KETTLE Before using
your kettle for the first time, fill the kettle to the "MAX" line with cool water. Boil water
without any additives. After boiling, carefully pour out the water into your sink and
repeat once more. This will ensure that any residues left over from the manufacturing
process is completely removed.
BOIL-DRY PROTECTION
Should you accidentally switch on an empty kettle, the built in boil dry safety protection
will automatically switch off power. If this occurs, unplug the kettle om the mains power
supply and allow the kettle to cool down bore filling with cool water.
DIGITAL KETTLE OPERATION
•Position the kettle base on a dry at surface and away from any potential heat
source
The maximum water level is marked
inside the kettle. Marked as “MAX
1.5L”.
The minimum water level is marked
inside the kettle too. Marked as “MIN
0.5L”.

Digital Touch Control Kettle R-7500 NEXT GEN
EN
7
•Unwind the length of cord required to reach the mains electrical outlet. Ensure
the cord does not hang over the work surface edge
•Remove the kettle from the base
•Open the lid. Fill the kettle with cool water, between the MIN and MAX
markings located inside the kettle
•Close the lid and place the kettle back onto its base, Make sure that the lid is
securely closed before boiling
Note: Always remove the kettle from its base before filling. Do not fill the kettle
above the MA X mark or below the MIN mark on the water gauge
•Plug the kettle into the mains electrical outlet
•Follow the instructions located in the TOUCH-CONTROLS GUIDE section.
Once you have made your touch-control selection, the kettle will sound with
two notification tones, indicating that the selected function is about to start.
The digital display will illuminate with real time temperature and count up as
the water temperature increases.
The digital display will also countdown in real time as the water temperature
decreases.
•Note that you can stop the kettle boiling or keep warm process at any time by
pressing the POWER button
•Should you lift the kettle from its base during a functions cycle and place it
back on to the base within 2 minutes the kettle will sound with one notification
tone and resume the pre-selected function cycle. Please do not add water into
the kettle during a boiling or keep warm cycle. Always ensure to remove the
kettle from the base before pouring.
•When the water has boiled (without using the keep warm cycle) the kettle will
enter standby mode and its display will turn off approximately 30 seconds. To
wake the appliance, press any button.
CAUTION:
•Never open the lid or touch its steel surfaces during boiling. Please beware of
escaping steam from the lid of the kettle when in use.

Digital Touch Control Kettle R-7500 NEXT GEN
EN
8
•Do not fit the kettle backwards as water might get into and onto the control
area. If this happens, let the kettle dry thoroughly before next use. We
recommend placing it in a dry, warm area for 12 hours.
•You may see moisture on the base when you lift the kettle. Do not worry as
it's the steam used to switch the kettle off automatically. The steam
condenses and escapes via vents under the kettle.
•You may notice some discolouration on the floor of the kettle. This is normal
and is due to the bonding of the element to the kettle floor.
KEEP WARM FUNCTION
Should you lift the kettle off its base during the keep warm cycle and place it back on to
the base then the keep warm cycle will stop and the kettle will go into standby mode.
We recommend that you do not fill the kettle with cool water during the keep warm
cycle.
Should you lift the kettle off its base during the keep warm cycle and fill it with water
then the keep warm cycle will stop and the kettle will go into standby mode.
If the kettle is empty, cancel the keep warm cycle to prolong the life of your appliance.
TOUCH CONTROL GUIDE

Digital Touch Control Kettle R-7500 NEXT GEN
EN
9
STANDARD BOILING
Press this button to switch on the kettle/wake it from standby mode. The
screen will display"ECO"and 100 on the digital tube, then start heating up without using
the keep warm function. It will heat to boiling point (100℃).
Press the button twice to make sure the kettle powers off completely once
your water is boiled.
Long press button, or 5 minutes without any operation, then will enter to
shutdown mode.
Unique count down / count up digital
thermometer
Preset temperature controls
Warming functions
Power button
Eco function
Preset menu
button

Digital Touch Control Kettle R-7500 NEXT GEN
EN
10
After the machine turn to the shut down mode, press one time the or
button, and then turn to the standby mode, shows the water temperature in real time.
Beep tip and without beep tip exchange follow as below:
Long press the “mode”& “start/cancel”button together, cancel the beep tip
(After finish the functions will sound beep tip). Long press again the &
button together, recover the Beep tip.
MILK-40℃
Press this button three time and hear a beep then automatically to heat your
water/milk to 40°C(ECO FUNCTION)
The milk function is also suited to heating water 40℃.
Water reheated to, or cooled down, this temperature is ideal for powdered milk
formula.
WARNING: IF THE KETTLE USED FOR WARMING MΙLK THE INTERIOR MUST BE
CLEANED WITHIN 10 MINUTES OF HEATING THE TO AVOID DAMAGE TO THE
KETTLE.

Digital Touch Control Kettle R-7500 NEXT GEN
EN
11
Press and hold this button three time, hold it for 2 seconds and hear a beep
then automatically to heat your water/milk to 40℃and keep it warm for approximately
90 minutes (WARM FUNCTION).
TEA-80℃
Press this button once and hear a beep then automatically to heat your
water/milk to 80℃(ECO FUNCTION).
Press this button once, hold it for 2 seconds and hear a beep then
automatically to heat your water/milk to 80℃and keep it warm for approximately 90
minutes (WARM FUNCTION).
CAFE / COFFEE -90℃
Press this button twice and hear a beep then automatically to heat your
water/milk to 90℃(ECO FUNCTION).
Press this button twice, hold it for 2 seconds and hear a beep then
automatically to heat your water/milk to 90℃and keep it warm for approximately 90
minutes (WARM FUNCTION).

Digital Touch Control Kettle R-7500 NEXT GEN
EN
12
THE PERFECT TEMPERATURES TIPS AND TRICKS
TIPS AND TRICKS
Use the optimal water temperature to brew perfect hot drinks. The correct water
temperature helps you extract just the right amount, avoiding strong or weak brews. It
also ensures that the taste you get, is exactly as it should be.
MILK: Use the milk function to heat milk to 40 ℃. To sterilize the water for use in
baby’s formula, first boil the water properly to eliminate harmful bacteria. It is important
to let the water cool before using the convenient milk function to reheat to 40℃before
mixing it with the baby’s formula, Test the temperature of the milk/formula on the inside
of your wrist before giving it to the baby. It should be body temperature, which means it
should feel warm or cool, but not hot.
TEA: Teas are too delicate for boiling water, with the ideal temperature being 70℃for
white tea. Advised temperatures vary across the tea spectrum: black and oolong teas
require water at around 85℃, whereas herbal infusions need 100℃, and for
chamomile, around 90.
COFFEE: Boiling water can burn coffee. The best temperature for making it is
between 80℃(instant coffee) and 96℃(brewing).
CARE AND CLEANING

Digital Touch Control Kettle R-7500 NEXT GEN
EN
13
EXTERIOR CLEANING
Let the kettle cool down before cleaning. Before you clean your kettle, unplug and
make sure all water is poured out from the kettle. Do not immerse the appliance or its
base in water or any other liquid, or hold it under a running tap to clean.
Dry with a clean, dry, soft cloth. Gently wipe the kettle body and base with a damp
cloth. Never use detergents, harsh chemicals or abrasive cleaning agents on your
kettle.
INTERIOR CLEANING
We recommend that you descale your kettle on a monthly basis, Any buildup of scale
causes overheating, which reduces the life of the element, and may trigger the boil dry
safety protection to engage. Limescale may be white, slightly coloured or rust-looking,
but it is normally visible. Kindly note that products returned under guarantee with faults
related to scale will be subject to a repair charge.
Over time, your kettle may experience a build up of limescale. To remove limescale
follow the easy steps below:
•Fill your kettle with a mixture of equal parts water and household vinegar or
lemon juice
•Let the mixture sit in the kettle for 1(one) hour and then boil
•Pour out the mixture from the kettle and rinse thoroughly with clean water
•Repeat this last process several times

Digital Touch Control Kettle R-7500 NEXT GEN
EN
14
WARNING: IF THE KETTLE USED FOR WARMING MΙLK THE INTERIOR MUST BE
CLEANED WITHIN 10 MINUTES OF HEATING THE TO AVOID DAMAGE TO THE
KETTLE.
STORAGE
•Ensure that all parts are dry before storing.
•Never store the kettle while it is still wet or dirty.
•Store the appliance in its box or in a clean.
•Never wrap the power cord around the appliance.
TROUBLESHOOTING
Follow the instructions in this handy troubleshooting guide should your kettle not be
operating correctly:
Problem
Possible causes
Solution
Indicator/Digital screen
1. Power cord not
firmly plugged in
2. Circuit board is
damaged
1. Check the electrical plug
2. Send to your nearest Service
Centre
Unable to heat
1. Heating element is
damage
2. Circuit board is
Send to your nearest Service
Centre

Digital Touch Control Kettle R-7500 NEXT GEN
EN
15
damaged
3. Thermostat is
damaged
Unable to switch off
after boiled
1. Too much limescale
at the temperature
sensor
2. Machine failure
1. Remove the limescale
2. Send to your nearest Service
Centre for maintenance
Switch off before boiled
1. Too much limescale
at the temperature
sensor
2. Machine failure
1. Remove the limescale
2. Send to your nearest Service
Centre for maintenance
Display Error
Guide
Reasons
Solution
E1
Thermostat has
opened or become
exposed
Cancel function selection by
pressing the POWER button.
Send to your nearest Service
Centre
E2
Thermostat has
experienced a short
Cancel function selection by
pressing the POWER button.
Send to your nearest Service
Centre
E3
Kettle over-heated
Cancel function selection by
pressing the POWER button.

Digital Touch Control Kettle R-7500 NEXT GEN
EN
16
Select your desired function only
once the temperature has
dropped below 100℃
E4
Abnormal zero-cross
signal
Cancel function selection by
pressing the POWER button.
Send to your nearest Service
Centre
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special local authority differentiated waste collection centre or to a
dealer providing this service.
Disposing of a household appliance separately avoids possible negative
consequences for the environment and health, deriving form inappropriate disposal
and enables the constituent materials to be recovered to obtain significant savings in
energy and resources. As a reminder of the need to dispose of household appliances
separately, the product is marked with a crossed-out wheeled dustbin.