Roller Grill SBM 40 M User manual

14
SG03217
INSTRUCTIONS FOR INSTALLATION AND USE
WALL MIXTE SALAD’BAR
SBM 40 M
Made in France
January 2013

WALL MIXTE SALAD‘BAR
SBM 40 M
Congratulations for the acquisition of this upmarket appliance made in France. You
chose an appliance which alloys the best technical qualities with a big user-
friendliness. We wish you the biggest contentment
1. SECURITY INSTRUCTIONS
Please respect these instructions scrupulously to avoid any risk of fire, electric shock,
scald or other wounds and damage. During the use of this appliance, fundamental
circumspection of security must always be noticed, such as:
-Take into account the instructions to be systematically kept with the appliance.
-Install the appliance always in instructions respect. A 10 cm distance minimum
with the partition or the wall is necessary.
-Protect the appliance from direct light of the sun, frost and humidity.
-Never leave the appliance within the reach of children or disabled persons with-
out surveillance.
-The machine has to be used only by qualified person.
-Never move the appliance when it is working.
-Check that the appliance is definitely off before connecting it up or disconnect-
ing it.
-Do not touch the hot surfaces of the appliance. The temperature of the hot sur-
faces can be very important when the appliance is working. Always use handles
and control knobs.
-Do not use the appliance for other functions than determined use.
-Do not leave the electrical cord in contact of hot surfaces.
-The appliance should not be used close to combustible materials.
-During use, look after not to obstruct hearings of aeration of the appliance
-To avoid any electric shock, never plunge the cord or plug in water or quite
other liquid.
-If the cord is harmed, it must be replaced by the producer, its after sale service
or persons of similar skills to avoid any risk.
-Entrust repairs only to a skilled person.
-Use only spare parts of origin.
-Before cleaning the appliance, do not forget to disconnect it.
2. CONTENTS OF CARDBOARD PACKAGING
Device: a salad’bar
Accessories: -Two castors without brake + two castors with brake
-A light reflector
-A left upright and a right upright
-Two stainless steel protections
-Screws
-A mirror
-The present note
See exploded view at the end of the document 213

Nomenclature SALAD’BAR MURAL CHAUD
Spare parts WALL WARMING SALAD’BAR
12
Rep Code Qty Pièce Spare part
177047 1Toit Roof
2 77050SE 1Montant gauche Left upright
3 C03007 1 Cordon + prise Cord with plug
4A10001 1 Serre cable Cord closer
5 SF08019 2 Roue sans frein Wheel without brake
6 SA03072 1 Condenseur Condensor
7 SA03073 1 Hélice Fan blade
8
SA03024/F
1 Compres seur Com pressor
977024 1Support compresseur Compressor holder
10 77051SE 1Montant droit Right upright
11 SH01103 1 Plexiglas Plexiglass
12 SA18035 1Led Led
13 SH01087 1 Séparation plexiglas Plexiglass separation
14 SD02107 1 Rés istance Heating element
15 SF08018 1 Roue avec frein Wheel with brake
16 77035SE 1Support composant Control panel holder
17 A08009 1 Voyant vert Green pilot light
18 SA06051 1Thermostat sécurité Safety thermostat
19 A14093 1 BoutonKnob
20 SA06050 1Thermostat Thermostat
21 SA06030 1
Thermostat électronique
Electronic therm ostat
22 A07025 3 InterrupteurSwitch
23 SA03012 1Moteur ventilateur Fan m otor
24 SA03093 1Alimentation led Led alimentation
3. CONFORMITY OF USE
Use the salad’bar only to:
-keep warm (+20° to + 90°C) your hot starters, meat, vegetables, readymade
dishes…during working and service hours. It enables you keeping warm products
already cooked or hot.
-keep cold (+2° to +10°C) your cold starters, shellfish, meat, desserts during
working and service hours. Afterwards they will be stores in a conventional cool
chamber.
4. WAY OF FUNCTIONING
This salad’bar is fitted with 2 warming containers and 2 refrigerated containers
To turn on your salad’bar, press on the switches (n°3 and 5 on picture): the green
pilot light (n°2 on picture) and the electronic thermostat (n°1 on picture) ignite.
Set the temperature of the thermostat (n°6 on picture) on the desired temperature for
the warming side. The electronic thermostat from the refrigerated part is preset in
factory.
Press on the switch (n°4 on picture) to turn on the light (n°7 on picture).
Once water is hot, you can place the GN containers.
3
1 2
6543
7
8

Electronic thermostat Green pilot light
On/off switch (refrigerated part) On/off light
On/off switch (warming part) Thermostat
Led light Mirror
5. FUNCTIONING / MANIPULATION
a) Installation / assembly:
-Unpack carefully the appliance from its packaging
-Place the equipment on a stable and heatproof surface.
-Never place the device near a wall or near a partition makes of combustible mate-
rials even if it is very well isolated.
-A distance of 10 cm from the partition or the wall is considered enough.
-Remove the protective film from the appliance.
-Position the accessories (see 11. Installation guide)
b) First starting:
For the warming part (right container)
Fill the container with water (about 5 cm above the heating elements) before switching
on the salad’bar.
Do not let it run without water : it could damage the heating elements and irremediably
bend the container.
To avoid quick evaporation, cover the whole tank with containers or lids.
First cleaning
Clean the device before the first use. (See 6 Cleaning)
Connection of the device
-Check that the tension and the frequency of the electricity network suit to the val-
ues indicated on the descriptive plate.
-Check that neither the cord nor the plug are damaged
-Make sure that every control knob is positioned on 0.
-Unwind completely the electric power cable and connect it in a normalised plug
with the earth.
-The device is connected.
NB: in case of connection of the device in a plug without earth protection or directly
on the electricity network, confide its connection to a qualified person .4
6
4
21
5
3
78
Your salad’bar is ready. You can place it and plug in with normalized 220-240 V ~
according to the instructions manual.11
C. Mounting of the plexiglas
Remove the protective film.
Place the plexiglas under the stainless
steel roof (Picture L) and fix the screws
D (Picture F on page 2).
6. Connection
Connect every wire. ( Picture M)
7. Fix the protection for wires
Fix the stainless steel protection for wi-
res with the screws B (Picture F on
page 2 + Picture N)
8. Final fixation of the mirror
Insert both screws C on the back top of
the uprights (Picture F on page 2 + Pic-
ture O)
Photo N
Photo M
Photo O
Picture L

Picture H
Right upright
A. Remove the protective film from the right
upright.
Unscrew the protective screw, put the mirror in
the slide of the upright and fix again the screw
as well as the back screw B (Picture F on page
2).
Attention: Both wires should be outside (Picture
I)
At this stage, the mirror is at its place but must
be hold.
5.Mounting of the top parts
A. Mounting of the roof
Remove the protective film from the roof and put
the roof on both uprights. (Picture J)
B. Mounting of the top shelf
Place the shelf on the roof with both plastic sha-
ped parts up. (Picture K)
Fix the screws A (Picture F on page 2).
Picture J
Picture I
Picture K
c) Use of device :
Elements of command and display
Starting
Refrigerated part (left container)
Press on the switch (n°3 on picture), the machine is on. The preset electronic
thermostat (n°1 on picture) flashes and displays the temperature.
Wait until the salad’bar is at the right temperature
Warming part (right container)
Press on the switch (n°5 on picture), the green pilot light (n°2 on picture) ignites.
Turn on the thermostat (n°6 on picture) on the desired position.
Press on the switch (n°4 on picture) to turn on light.
Temperature setting
Refrigerated part (left container)
The electronic thermostat (n°1 on picture) is preset in factory. It can be adjusted if
necessary. To modify the temperature, press the "set" key for 5 seconds: the pro-
grammed value is displayed and the LED flashes. Use the arrows to adjust your
temperature and then valid by pushing on set.
Warming part (right container)
Set the temperature by positioning the thermostat (n°6 on picture) to the desired
temperature.
Stopping the appliance
-Set each switch (n°3, 4 and 5 on picture) on 0: the appliance is no longer func-
tioning.
-Let the device cool 5
Command/Display Function
Refrigerated part (left container)
Electronic thermostat (n°1 on pic-
ture) Temperature setting
Switch I/0 (n°3 on picture) On/off
Warming part (right container)
Green pilot light (n°2 on picture) Machine on (pilot light on)
Machine off (pilot light off)
Switch I/0 (n°5 on picture) On/off
Thermostat (n°6 on picture) Temperature setting
Switch I/0 (n°4 on picture) Light on / Light off

-Disconnect the power cable.
-Clean the appliance. (see 6. Cleaning)
d) Breakdown / repair:
In case of breakdown or of damaged part, please call your after-sales service and
confide any technical operation to qualified person.
When you contact the after-sales service of your distributor or your store, give him
the complete reference of your device (commercial name, type and serial number).
This information appears on the visible descriptive plate behind the device.
6. CLEANING AND MAINTENANCE
-Disconnect the device.
-Let cool completely the device before any technical intervention or cleaning.
-Clean regularly the metallic parts after each use by using only use non-abrasive
products, warm water and wash liquid: avoid the abrasive towelling. Rinse your
device with a wet sponge and dry it with a soft cloth.
-Never clean the device under a water jet, the infiltrations would risk to dam age it
in a irreparable way.
-Never immerse the cord or the plug in the water or quite other liquid to avoid any
electric shock.
-Regularly change the water to avoid any scale deposit
-Never use abrasive product or vinegar; it could damage the container in irremedi-
able way.
7. TECHNICAL SPECIFICATIONS
Wires colours correspondence Phase Brown / Black / Grey
Neutral Blue
Earth Yellow-Green 6
Model SBM 40 M
Outside di-
mensions 1495x855x1405 mm
Weight 100 Kg
Temperature +20° to +90° C (warming part)
+2° to +10° C (refrigerated part)
Power 2 250 W
Gas R 134 A
Bb Element 1
Current 10 A
Voltage 220-240 V ~
Colour Wenge/ Light oak /
Mahogany
3. Mounting of left / right
uprights and of the mirror
Left upright
A. Remove the protective film
from the left upright. (Picture C)
B. Unscrew the protective screw
on the container (Picture D) and
fix the left upright with the screw.
(Picture E)
C. Fix the screw B (Picture F)
behind the left upright (Picture
E).
Mounting of mirror
The mirror must be taken by 2
persons and be put along the
slide on the left upright. One per-
son must support it in its position.
.(Picture G)
Picture E
Picture D
Pho-
Picture G
Picture F
Picture C

8
Exclusion clauses of the guarantee
Bad installation and bad maintenance, in particular if they do not respect cur-
rent regulations or instructions appearing in this user guide.
Cannot benefit from the guarantee the repairs required as a result of false operations,
of inappropriate use, of carelessness or of excess loads of the device, as well as
those resulting from variations of the power supply, over tension or from defective in-
stallations.
The damage due to shocks, bad weather is not flatware by the guarantee. The mate-
rial travels at the risks of the user; in case of delivery by carrier, the consignee has to
have reservations towards the carrier before any delivery of the device.
The guarantee comes to an end in case of intervention, of repair, of modification by no
qualified persons, or of use in inappropriate purposes.
11. INSTALLATION GUIDE
1. Unpack the salad’bar carefully
Remove the external protective films and hoopings. Unpack the small parcel placed in
the middle of the salad’bar. (This parcel contains the wheels and the screws.)
2. Mounting of the castors
Elements:
-2 wheels with brake system
-2 wheels without any brake system
-16 screws 8x25
-16 rings
(Picture A)
A. Lift up carefully the salad’bar and
turn it perpendicular to the pallet.
(Photo B)
B. Mount both castors with brake sys-
tem on the front on the side of the ope-
rating panel and both castors without
brake system on the back. Fix all parts
with a spanner of 13.
C. Remove the pallet.
D. Remove both brackets at the bot-
tom of the salad’bar. 8
Photo B
Picture B
Picture A
8. NORMS AND LEGALS DISPOSALS
The device is conform to :
IEC/EN 60335-1
IEC/EN 60335-2-49
IEC/EN 60335-2-89
EN 55014-1 + 55014-2
EN 61000-3-2 + 61000-3-3
9. ELIMINATION OF THE ELECTRIC AND ELECTRONIC WASTE
The device respects the directives:
2002/96/CE ( DEEE) N°34270064800021
2002/95/CE ( ROHS)
2066/95 CE
2004/108 CE
Reach rule
Never put the device among household waste.
The device must be put down in a centre of recycling for the electric equipments.
The materials of the device are indeed reusable. By eliminating correctly the electric
and electronic wastes, the recycling and quite other shape of re-use of worn equip-
ments, you participate in a significant way in the environmental protection.
For any information about the collection of electric and electronic waste, please
contact your distributor.
10. GUARANTEE
Conditions of guarantee
The guarantee applicable to any device is the commercial guarantee of the distribu-
tor or the retailer. Please contact the store where you bought your device to know
the precise conditions.
The guarantee grants no right for damages.
The dispositions which follow are not exclusive of the profit of the legal guarantee
planned by articles 1641 and following ones of the Civil code relative to the defects
and the latent defects.
7