Romina 4510s User manual

ASSEMBLY INSTRUCTIONS
FOR YOUR 4510s
STATIONARY / CONVERTIBLE
CRIB
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
20 Corporation Row, Edison, NJ 088 7
Phone
1
[phone], Fax [phone]
www.rominakidsfurniture.com
WARNING:
.
THE PROPER USE OF THIS CRIB IS
IMPORTANT FOR YOUR BABY'S SAFETY. TO KEEP
YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH,
CAREFULLY READ AND FAMILIARIZE YOURSELF
WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE
USE
DO NOT THROW THIS INSTRUCTION BOOKLET.
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
AND BY THE
AMERICAN SOCIETY FOR TESTING AND
MATERIALS
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL.
*DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
ADRY CLOTH, WILL PRESERVE THE ORIGINALLUSTERAND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECUERLY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
DO NOT
ROMINA FURNITURE
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.

P
F
F
M
S
CP
CP
CP
CP
P
Please locate and confirm that
you have the following parts:
F. fixed side = 2
P. panel = 2
S. stabilizing bars = 2
M. mattress support = 1
CP. corner piece = 4
one bag of hardware with the following:
1. Allen wrench = 1
2. one storage pouch and two plastic ties
3. Allen bolts (1 31/32" or 50 mm) = 8
4. Allen bolts (2 3/8" or 60 mm) = 4
5. Allen bolts (3 15/16" or 100 mm) = 8
6. barrel nuts = 4
7. round head bolts (1 3/16" or 30 mm) = 4
8. round head bolts (19/32" or 15 mm) = 4
9. "butterfly" type nut = 4
10. bigger “internal star” lock washer = 20
11. smaller “external star” lock washer = 8
Required tools:
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not supplied), flat screwdriver
Do not use a power screwdriver which
can cause screws to break or strip
(not
supplied).
6
1
The item
number of your
product is located on
the inner side of the left
pannel, on a black and white
label. Please, refer to this number
in the event that you need to call
ROMINA FURNITURE or your local
distributor.
Note:
Thank you.
Note: The letter that identify
a part is the first letter of the
respective part name (such
method is employed to
facilitate parts recognition
between the drawings and
the parts list).
Phillips screwdriver (not supplied)
6
Note:
TIGHTEN COMPLETELY
During the assembly process whenever using screws or
bolts, check
each by placing the screw / bolt on the upper diagram which is
drawn in actual size. Be sure to use the proper size and shape
specified in the instructions.
Be sure to the screws / bolts when
you are asked to do this.
11
10
printed in full size
5
3
4
11
10 9
7
8
6

FIGURE 1
CP
CP
F
S
6
4
6
4
3
3
3
3
TAKE CARE NOT TO
SCRATCH THE FINISH
OF YOUR PARTS!
STEP 1
Attach two corner pieces to one of the fixed sides using 4 smaller Allen bolts , 4 washers and
the Allen wrench supplied .
Then attach one of the stabilizing bars to the corner
pieces using 2 medium Allen bolts , 2 washers , 2 barrel nuts and the Allen wrench supplied .
(CP) (F) (3) (10)
(1)
(S)
(CP) (4) (10) (6) (1)
(follow the instructions attached to the stabilizing bar)
Push the barrel nut into the hole drilled in the corner piece then align the straight slot in the head of the barrel
nut vertically, so the threads in the bolt will insert in the barrel nut. You can adjust the position of the barrel nut
with a flat head screwdriver (not supplied) or a coin.
Push the Alen bolt through the stabilizing bar. Start the threads by hand to assure you don't strip
the threads, then use the suplied Allen wrench.
Repeat the same actions for the second fixed side & stabilizing bar .(F) (SB)
10 10
10
10
10
10

STEP 2
Tighten completely all the 12 Allen bolts used in STEP 1 for
both fixed sides.
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN
COMPLETELY ALL THE ALLEN
BOLTS LISTED IN .
12
STEP 1
FIGURE 2
CP
CP
F
S
this shows how your parts should look like after completing STEP 1
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN COMPLETELY!
TAKE CARE NOT TO
SCRATCH THE FINISH
OF YOUR PARTS!

STEP 3
Attach the parts of your crib as they resulted after to the end
panels using 8 bigger Allen bolts , 8 washers and the
supplied Allen wrench .
STEP 2
(P) (5) (10)
(1)
Tighten completely all the 8 bigger bolts!
P
P
5
5
5
5
FIGURE 3
5
5
5
5
P
P
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN
COMPLETELY ALL THE ALLEN BOLTS
LISTED IN .
8
STEP 3
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN COMPLETELY!
TAKE CARE NOT TO
SCRATCH THE FINISH
OF YOUR CRIB!
F
F
F
S
10
10
10
10
10
10
10
10

LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
Assemble the mattress support using 4 bigger
round head bolts , 4
STEP 4
(7)
Do not tighten the bolts completely at
this step, you will be asked to do this later.
"butterfly" type nuts , 4
smaller lock washers and a Phillips
screwdriver (not supplied). The lock washer must
be attached to the bolt after the bolt passed
through the frame and the metallic bracket of the
mattress support and before attaching the nut.
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all the four bolts in the same position
(see ).
(9)
(11)
FIGURE 4
NOTE: THE STYLE OF YOUR CRIB OR
OF YOUR MATTRESS SUPPORT MAY
VARY FROM WHAT IS PICTURED IN
THE INSTRUCTION SHEET
FIGURE 4
7
9
7
9
7
9
7
9
7
9
11
11
11
9
11
To adjust the vertical position of your mattress support you must remove all the four bolts & nuts
loosen all the four bolts , lower the frame and insert the bolts back into the corresponding holes,
according to the desired height (see ). Then, you must attach the lock washers and the nuts
as described in and tighten all the bolts completely.
ADJUSTING THE HEIGHT OF YOUR MATTRESS SUPPORT
(7+11+9),
(8+11) (7)
FIGURE 4 (11) (9)
STEP 4
ADJUSTED THE HEIGHT OF YOUR
MATTRESS SUPPORT
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the stabilizing bars. Before tighten
the bolts, you must slightly press the mattress support frame to make sure this position is achieved.
WARNING:
IT'S VERY IMPORTANT TO TIGHTEN COMPLETELY ALL THE 8 BOLTS
(7+11+9) & (8+11) AFTER YOU HAVE
.
TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH,
11

8
8
8
8
FIGURE 5
7
6
7
6
7
6
7
6
S
F
F
P
P
M
STEP 5
Attach the mattress support to the
stabilizing bars using 4 smaller round
head bolts , 4 smaller washers and a
Phillips screwdriver (not supplied).
(M)
(S)
(8) (11)
Tighten completely all the 8 bolts & nuts
(7+11+9, 8+11) involved in
mattress support fixing using a
Phillips screwdriver (not
supplied)!
The lock
washer must be attached to the bolt before
inserting the bolt through the metallic
bracket of the mattress support.
WARNING:
VERY
IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN COMPLETELY
ALLTHE BOLTS LISTED IN .8STEP5
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN COMPLETELY!
11
11
11
11
11
11
11
11

FIGURE 6
this shows how your crib should look like after completing assembly
After you completed , attach the
storage pouch supplied to the mattress
support spring using the two plastic ties also
supplied. Store this instruction booklet in the
storage pouch for future use.
STEP 5

TWIN SIZE BED OPTION OF YOUR
4510s STATIONARY / CONVERTIBLE CRIB
(THE CONVERSION KIT IS SOLD SEPARATELY)
NOTE:
CKC 4510 C K C 4510 .
4515.
YOUR 4510s STATIONARY / CONVERTIBLE
CRIB CAN CONVERT INTOATWIN SIZE BED WITH
THE PURCHASE OF ROMINA FURNITURE ITEM
CODE ( ONVERSION IT FOR RIBS, code )
ASSEMBLY INSTRUCTIONS FOR TWIN SIZE BED OPTION CAN BE
FOUND INSIDE OF CKC PACKAGE.
ALSO, YOU CAN HAVE THE TWIN BED FROM THE BEGINNING WITH THE
PURCHASE OF ROMINA FURNITURE ITEM CODE
PLEASE, CONTACT ROMINA FURNITURE OR YOUR LOCAL
DISTRIBUTOR FOR MORE INFORMATION.

TODDLER RAIL OPTION OF YOUR
45 STATIONARY / CONVERTIBLE CRIB10s
(THE TODDLER RAIL IS SOLD SEPARATELY)
NOTE: Y
ASSEMBLY INSTRUCTIONS FOR
TODDLER RAIL CAN BE FOUND INSIDE
OF THE TR 4510 PACKAGE.
PLEASE, CONTACT ROMINA
FURNITURE OR YOUR LOCAL
DISTRIBUTOR FOR MORE
INFORMATION.
OU CAN ATTACH A TODDLER
RAIL TO YOUR CRIB WITH THE
PURCHASE OF ROMINA FURNITURE
ITEM ( ODDLER AIL 4 ).TR 4510 T R 510

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina furniture item as
beautiful and unique as you and your baby are.
· To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of this
fine finish of your Romina Furniture product.
Visit
for updates, special offers and more new designs.
www.rominakidsfurniture.com
Team
Thank you for beeing one of our distinguished clients.