Romina 301 Nerva User manual

ASSEMBLY INSTRUCTIONS
FOR
3
YOUR
01 NERVA CRIB
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
WARNING:
.
THE PROPER USE OF THIS CRIB IS
IMPORTANT FOR YOUR BABY'S SAFETY. TO KEEP
YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH,
CAREFULLY READ AND FAMILIARIZE YOURSELF
WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE
USE
DO NOT THROW THIS INSTRUCTION BOOKLET
20 Corporation Row, Edison, NJ 088 7
Phone
1
[phone], Fax [phone]
www.rominakidsfurniture.com
Furniture
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
AND BY THE
AMERICAN SOCIETY FOR TESTING AND
MATERIALS
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL.
*DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
ADRY CLOTH, WILL PRESERVE THE ORIGINALLUSTERAND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECUERLY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
DO NOT
ROMINA FURNITURE
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.

Please locate and confirm that
you have the following parts:
F. front panel = 1
B. back panel = 1
L. left panel = 1
R. right panel = 1
M. mattress support = 1
one bag of hardware with the following:
1. round head bolts (19/32" or 15 mm) = 4
2. Allen bolts (2 3/8" or 60 mm) = 10
3. one storage pouch and two plastic ties
4. Allen wrench = 1
5. round head bolts (1 3/16" or 30 mm) = 4
6. "butterfly" type nut = 4
7. bigger “internal star” lock washer = 10
8. smaller “external star” lock washer = 8
Required tools:
.
CAUTION:
Allen wrench (supplied), Phillips
screwdriver (not included)
Do not use a power screwdriver which
can cause screws to break or strip
6
4
F
B
L
R
M
Note:
TIGHTEN COMPLETELY
During the assembly process whenever using screws or bolts, check
each by placing the screw / bolt on the upper diagram which is drawn in actual size.
Be sure to use the proper size and shape specified in the instructions.
Be sure to the screws / bolts when you are asked to do so.
The item
number of your
product is located on
the inner side of the left
pannel, on a black and white
label. Please, refer to this number
in the event that you need to call
ROMINA FURNITURE or your local
distributor.
Note:
Thank you.
Note: The letter that identify
a part is the first letter of the
respective part name (such
method is employed to
facilitate parts recognition
between the drawings
and the parts list).
Phillips screwdriver (not supplied)
printed in full size
2
15
786
3
8
7

FIGURE 1
this shows how your crib should look
after completing STEP 1
STEP 1
Attach the right panel of your crib to the
back panel using 3 Allen bolts , 3
washers and the Allen wrench supplied
.
Do the same for the left panel .
(R)
(B) (2)
(7)
(4)
(L)
Do not tighten the bolts completely at this
step, you will be asked to do so later.
B
R
2
2
2
B
R
L
7
7
7

Assemble the result of with the front
panel using 4 Allen bolts ,
and the Allen wrench supplied .
STEP 2
STEP 1
(F) (2)
(4)
4 washers
(7)
Do not tighten the bolts completely at this
step, you will be asked to do so later.
FIGURE 2
this shows how your crib should look
after completing STEP 2
B
L
R
F
2
2
2
2
BR
LF
7
7
7
7

LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
Assemble the mattress support using 4 bigger
round head bolts , 4
STEP 3
(5)
Do not tighten the bolts completely at
this step, you will be asked to do this later.
"butterfly" type nuts , 4
smaller lock washers and a Phillips screwdriver
(not supplied). The lock washer must be attached
to the bolt after the bolt passed through the frame
and the metallic bracket of the mattress support
and before attaching the nut.
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all the four bolts in the same position
(see ).
(6)
(8)
FIGURE 3
NOTE: THE STYLE OF YOUR CRIB
OR OF YOUR MATTRESS SUPPORT
MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION
SHEET
FIGURE 3
5
6
5
6
5
6
5
6
5
6
8
8
8
8
8
To adjust the vertical position of your mattress support you must remove all the four bolts & nuts
loosen all the four bolts , lower the frame and insert the bolts back into the corresponding holes,
according to the desired height (see ). Then, you must attach the lock washers and the nuts
as described in and tighten all the bolts completely.
ADJUSTING THE HEIGHT OF YOUR MATTRESS SUPPORT
(5+8+6),
(1+8) (5)
FIGURE 3 (8) (6)
STEP 3
ADJUSTED THE HEIGHT OF YOUR MATTRESS SUPPORT
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the inner wooden blocks. Before
tighten the bolts, you must slightly press the mattress support frame to make sure this position is
achieved.
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO TIGHTEN COMPLETELY ALL THE 8 BOLTS (5+8+6) &
(1+8) AFTER YOU HAVE .

Insert the mattress support into the crib and fix it
on the back panel through the wooden blocks
using 2 rounded head bolts , 2 washers and
the Phillips screwdriver (not supplied).
Fix the mattress support on the front panel
through the wooden blocks as described above.
STEP 4
(M)
(B)
(1) (8)
(F)
Tighten completely the four rounded head
bolts listed above.
The lock
washer must be attached to the bolt before inserting
the bolt through the metallic bracket of the mattress
support.
FIGURE 4
FLOOR
B
F
L
R
1
1
M
WARNING!
TIGHTEN COMPLETELY!
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN
COMPLETELY ALL THE 4 BOLTS LISTED
IN .STEP 4
TIGHTEN THE SAME BOLTS ON
THE FRONT PANEL OF YOUR CRIB!
1
8
8
8

FIGURE 5
Turn your crib with its feet back on the floor.
STEP 5

U
STEP 6
tighten
completely (2+7)
FIGURE 6
(2+7) (B)
(2+7) (B)
(2+7) (L)
(2+7) (R)
all the Allen bolts remained untighten from
all previous steps (see ).
You have a total of 10 Allen bolts, distributed as following:
- 4 bolts in the bottom part of back panel ;
- 2 bolts in the upper part of back panel ;
- 2 bolts in the front of left panel ;
- 2 bolts in the front of right panel .
REMINDER
sing the Allen wrench supplied,(4) you must
WARNING:
VERY IMPORTANT
TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
TO TIGHTEN
COMPLETELY ALL THE 10 ALLEN BOLTS
LISTED IN .STEP 6
FIGURE 6
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN COMPLETELY!
TIGHTEN THE SAME BOLTS ON
THE RIGHT SIDE OF YOUR CRIB!
2
2
2
2
2
2
2
2
2
2
7
7
7
7
7
7
7
7
7
7