Romina 6501 SP User manual

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of this
fine finish of your Romina Furniture product.
Visit
www.rominafurniture.com
for updates, special offers and more new designs.
Team
Thank you for beeing one of our distinguished clients.
Furniture
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
AND BY THE AMERICAN SOCIETY
FOR TESTING AND MATERIALS Europe's Kids Furniture
Furniture
4300 Northlake Ct, Ste E, Charlotte, NC 28216
Phone: [phone] / [email protected]
www.rominafurniture.com
DO NOT THROW OUT THIS
INSTRUCTION BOOKL E T!
these pictures shows how your cribs
should look like after completing assembly
IMPORTANT: PLEASE, READ ALL
INSTRUCTIONS BEFORE
ASSEMBLING! PLEASE,
SAVE INSTRUCTIONS
FOR FUTURE
USE
* READ ALL INSTRUCTIONS BEFORE
ASSEMBLING CRIB. KEEP INSTRUCTIONS
FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN
CRIB SIDES AND A MATTRESS THAT IS TOO SMALL.
ASSEMBLY INSTRUCTIONS
FOR YOUR
6501 & 7501 SP & TH
CONVERTIBLE CRIBS

page intentionally left blank

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH OR REGULAR BED. *USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL. *DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME, SUCH AS HOTATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
ADRY CLOTH, WILL PRESERVE THE ORIGINALLUSTERAND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER MATTRESS. *LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECURELY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB: AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES. DO NOT USE CRIB IF PARTS ARE DAMAGED OR BROKEN! CONTACT YOUR DEALER OR ROMINA FURNITURE FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO YOUR CRIB!
page intentionally left blank

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in slight color variations or richness in the finish. These differences make each Romina Furniture item as beautiful and unique as you and your baby are. · To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design. · Special water-based finishes are used to make this furniture safe for your baby. These finishes may be more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture, always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces must be moved/rotated to prevent discoloration in the finish. · Exposure to extreme variations of environmental conditions such as humidity and temperature can affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces! · Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing the finish to peel and the wood to warp. · Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces, heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect. · To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is recommended to rotate the changing pad's position frequently to avoid finish discoloration.
Phillips screwdriver (not included)
Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
HB
FB
LP
RP
2
MS
WB
SB
WR
12
6
8
Required tools: Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver (not
included).
CAUTION: Do not use a power screwdriver which
can cause screws to break or strip
Note: During the assembly process whenever using screws or bolts, check each by placing the screw / bolt on
the upper diagram which is drawn in actual size. Be sure to use the proper size and shape specified in the
instructions. Be sure to COMPLETELY TIGHTEN the screws / bolts when you are asked to do this.
printed in full size
11
13
10
5
6
8
9
1
10 13
Please locate and confirm that
you have the following parts:
HB. headboard = 1
FB. footboard = 1
LP. left panel = 1
RP. right panel = 1
SB. stabilizing bar = 2
MS. mattress support = 1
WR. wooden rail = 1
WB. wooden block = 2
one bag of hardware with the following:
1. Allen wrench = 1
2. storage pouch = 1
3. plastic tie = 2
4. Allen bolt (60mm - 2 3/8") = 8
5. rounded head bolt (30mm - 1 3/16") = 4
6. rounded head bolt (15mm - 19/32") = 4
7. "butterfly" type nut = 4
8. screw-in dowel = 2
9. cam fitting = 2
10. bigger “internal star” lock washer = 12
11. Allen bolt (70 mm - 2 3/4") = 4
12. wood screw (flat head 20mm - 3/4") = 3
13. smaller “external star” lock washer = 8
6501 TH & SP BOX CONTENT
Note:
T h e i t e m
number of your
product is located on
the inner side of the left
pannel, on a black and white
label. Please, refer to this number in
the event that you need to call ROMINA
FURNITURE or your local distributor. Thank you.
7
4

NOTE: YOUR CONVERTIBLE CRIB CAN CONVERT INTO A FULL SIZE BED WITH THE PURCHASE OF ROMINA FURNITURE ITEM CODE CKC
7501 (CONVERSION KIT FOR CRIBS, code 7501, SAME FOR BOTH CRIBS).
ASSEMBLY INSTRUCTIONS FOR FULLSIZE BED OPTION CAN BE FOUND INSIDE OF CKC PACKAGE.
PLEASE, CONTACT ROMINAFURNITURE OR YOUR LOCAL DISTRIBUTOR FOR MORE INFORMATION.
THE FULL SIZE BED OPTION OF
YOUR 6501 & 7501 SP & TH CONVERTIBLE CRIBS
(THE CONVERSION KIT IS SOLD SEPARATELY)
Please locate and confirm that
you have the following parts:
HB. headboard = 1
FB. footboard = 1
LP. left panel = 1
RP. right panel = 1
SB. stabilizing bar = 2
MS. mattress support = 1
WR. wooden rail = 1
WB. wooden block = 2
one bag of hardware with the following:
1. Allen wrench = 1
2. storage pouch = 1
3. plastic tie = 2
4. Allen bolt (60mm - 2 3/8") = 8
5. rounded head bolt (30mm - 1 3/16") = 4
6. rounded head bolt (15mm - 19/32") = 4
7. "butterfly" type nut = 4
8. screw-in dowel = 2
9. cam fitting = 2
10. bigger “internal star” lock washer = 12
11. Allen bolt (70 mm - 2 3/4") = 4
12. wood screw (flat head 20mm - 3/4") = 3
13. smaller “external star” lock washer = 8
Required tools: Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver (not
included).
CAUTION: Do not use a power screwdriver which
can cause screws to break or strip
Phillips screwdriver (not included)
Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
HB
2
MS
SB
WR
FB
LP
RP
12
8
6
printed in full size
11
13
10
5
6
8
9
1
10 13
Note: During the assembly process whenever using screws or bolts, check each by placing the screw / bolt on
the upper diagram which is drawn in actual size. Be sure to use the proper size and shape specified in the
instructions. Be sure to COMPLETELY TIGHTEN the screws / bolts when you are asked to do this.
7501 TH & SP BOX CONTENT
WB
Note:
T h e i t e m
number of your
product is located on
the inner side of the left
pannel, on a black and white
label. Please, refer to this number in
the event that you need to call ROMINA
FURNITURE or your local distributor. Thank you.
7
4

NOTE: YOU CAN ATTACH A TODDLER RAIL TO YOUR CRIB WITH THE PURCHASE OF ROMINA FURNITURE ITEM TR 7501 (TODDLER RAIL 7501, SAME FOR BOTH
CRIBS).
ASSEMBLY INSTRUCTIONS FOR TODDLER RAIL CAN BE FOUND INSIDE OF TR 7501 PACKAGE.
PLEASE, CONTACT ROMINAFURNITURE OR YOUR LOCAL DISTRIBUTOR FOR MORE INFORMATION.
THE TODDLER RAIL OPTION OF
YOUR 6501 & 7501 SP & TH CONVERTIBLE CRIBS
(THE TODDLER RAIL IS SOLD SEPARATELY)
STEP 1 (FOR BOTH 6501 & 7501) (Two adults are required to complete
this step)
Take the footboard of your crib (FB) and carefully place it on the floor with the drilled
side on top, taking care not to scratch its finish.
Insert 2 smaller Allen bolts (4) and 2 bigger washers (10) into a stabilizing bar (SB)
and attach it to the footboard using the Allen wrench supplied (1).
Be sure that the metallic inserts face of the stabilizing bar is facing towards the
inside of the crib (follow the instructions attached to the stabilizing bar).
Completely tighten these two bolts.
Attach the left and right panels (LP) &(RP) to the footboard, using 4 smaller Allen
bolts (4), 4 bigger washers (10) and the Allen wrench supplied (1).
Do not completely tighten the bolts at this step, you will be asked to do this later.
Attach the other stabilizing bar (SB) to the headboard using 2 smaller Allen bolts (4),
2 bigger washers (10) and the Allen wrench supplied (1).
Be sure that the metallic inserts face of the stabilizing bar is facing towards the
inside of the crib (follow the instructions attached to the stabilizing bar).
Completely tighten these two bolts.
Take the headboard (HB) and carefully place it over the part of your crib as resulted
after completing the above steps.
Using 4 bigger Allen bolts (11) , 4 bigger washers (10) and the Allen wrench supplied
(1), attach the headboard to the right and left panels (RP) &(LP).
Always start the threads by hand to assure you don't strip the threads.
Do not completely tighten the bolts at this step, you will be asked to do this later.
FIGURE 1
REQUIRED
WARNING: TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S VERY
IMPORTANT TO COMPLETELY TIGHTEN
ALL 4BOLTS LISTED IN STEP 1.
FB
HB
RP
LP
SB
SB
WARNING!
COMPLETELY TIGHTEN!
4+10
11+10
11+10
11+10
11+10
4+10
4+10
4+10
4+10
4+10
4+10
4+10
NOTE: THE STYLE OF YOUR CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET.

FB
MS
SB
4+10
6+13
5+13+7
5+13+7
5+13+7
5+13+7
4+10
4+10
4+10
6+13
6+13
6+13
NOTE: THE STYLE OF YOUR CRIB, HEADBOARD OR OF
YOUR MATTRESS SUPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET.
FIGURE D
STEP D (FOR BOTH 6501 & 7501) (Two adults are required to
complete this step)
Take the footboard of your crib (FB) as resulted after completing STEP C
and carefully place it back over the rest of the crib.
Using 4 smaller Allen bolts (4), 4 washers (10) and the Allen wrench
supplied (1), fix the footboard (FB) to the right and left panels (RP) &(LP).
Do not completely tighten the bolts at this step, you will be asked to do this
later.
STEP E (FOR BOTH 6501 & 7501)
Take the mattress support (MS) and adjust it to its lowest position (see
STEP 2 & ADJUSTING THE HEIGHT OF YOUR MATTRESS
SUPPORT for details).
Then mount it back on the stabilizing bars (SB) using all 4 smaller rounded
head bolts & washers (6+13) and a Phillips screwdriver (not supplied).
Now, you must completely tighten all 8bolts (5+13+7, 6+13) involved in
mattress support fixing using a Phillips screwdriver (not supplied) and all 4
Allen bolts remains un-tightened from all previous steps.
REMINDER
You have to tighten a total of 12 bolts, distributed as following:
- 4smaller Allen bolts (4+10) in the footboard (FB);
- 4smaller rounded head bolts (6+13) in the stabilizing bars (SB);
- 4bigger rounded head bolts (5+13+7) in the mattress support (MS).
STEP F (FOR BOTH 6501 & 7501) (Two adults are required to
complete this step)
Turn the resulted daybed with its feet back on the floor.
After completing assembly, your daybed should look like one of the models
depicted on the first pages of this section.
REQUIRED
WARNING!
COMPLETELY TIGHTEN!
WARNING: TO KEEP YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH, IT’S
VERY IMPORTANT TO COMPLETELY TIGHTEN ALL
12 BOLTS LISTED IN STEP E.
STEP 2 (One adult is required to complete this step)
Assemble the mattress support using 4 bigger round head
bolts (5), 4 "butterfly" type nuts (7), 4 smaller lock washers
(13) and a Phillips screwdriver (not supplied).
The lock washer must be attached to the bolt after the bolt
passed through the frame and the metallic bracket of the
mattress support and before attaching the nut.
There are three positions for the mattress support (from
the highest one for a newborn to the lowest one for a
child that is maximum 35" tall - see caution note). You
must adjust the height of the mattress support
depending of your child height by inserting all
four bolts in the same position (see FIGURE 2).
Do not completely tighten the bolts at
this step, you will be asked to do this later.
FIGURE 2
REQUIRED
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET.
5+13+7
5+13+7
5+13+7
5+13+7
5+13+7
MIDDLE POSITION
LOWEST POSITION
HIGHEST POSITION
HIGHEST POSITION
MIDDLE POSITION
LOWEST POSITION
A D J U S T I N G T H E H E I G H T O F Y O U R M A T T R E S S S U P P O R T
To adjust the vertical position of your mattress support you must remove all four bolts & nuts (5+13+7),
loosen all four bolts (6+13), lower the frame and insert the bolts (5) back into the corresponding holes,
according to the desired height (see FIGURE 2). Then, you must attach the lock washers (9) and the nuts (13)
as described in STEP 2 and completely tighten all the bolts.
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the stabilizing bars. Before tighten
the bolts, you must slightly press the mattress support frame to make sure this position is achieved.
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL 8 BOLTS (5+13+7)
& (6+13) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.

STEP C (FOR BOTH 6501 & 7501)
Using a Phillips screwdriver (not supplied) or just the hand, insert two screw-in dowels (8) into the metallic inserts holes found into each leg’s top (please
see the assembly tip for dowel correct positioning).
Insert two cam fittings (9) into the bigger holes found into the wooden blocks (WB), taking care that the little arrow of the cam is pointing downwards, to the
drilled face of the wooden block (see FIGURE 3 & C for details).
Using the factory installed wooden dowels, align the wooden blocks and attach them to the legs.
Then using the supplied Allen wrench (1) and moderate force, slightly rotate every cam fitting (9) clockwise (see the cam’s rounded arrow) by about 90 deg
to 120 deg until become tight.
Do not overtight the cams! This is not a fixture involved in your child safety.
Take the supplied wooden (WR) rail and attach it to your footboard using a Phillips screwdriver (not supplied) and three wood screws (12).
6
8
WB
WR
12
FB
12
12
6
8
WB
FIGURE C
REQUIRED
0+
-8
8
8
assembly tip
FIGURE 3
11+10
11+10
5+13+7
5+13+7
5+13+7
WARNING!
COMPLETELY
TIGHTEN!
WARNING!
COMPLETELY
TIGHTEN!
Y
REQUIRED
6+13
4+10
11+10
11+10
4+10
6+13
5+13+7
4+10
4+10
6+13
6+13
NOTE: THE STYLE OF YOUR CRIB, HEADBOARD OR
OF YOUR MATTRESS SUPPORT MAY VARY FROM
WHAT IS PICTURED IN THE INSTRUCTION SHEET
STEP 3 (FOR BOTH 6501 & 7501)
Mount the mattress support (MS) on the stabilizing bars as
these resulted after STEP 1, using 4 smaller rounded head
bolts (6), 4 smaller washers (13) and a Phillips screwdriver (not
supplied). The lock washer must be attached to the bolt before
inserting the bolt through the metallic bracket of the mattress
support.
Now, you must completely tighten all 8bolts (5+13+7, 6+13)
involved in mattress support fixing using a Phillips screwdriver
(not supplied) and all 8 Allen bolts (11+10, 4+10) remains un-
tightened from all previous steps (see FIGURE 3).
REMINDER
You have a total of 16 bolts, distributed as following:
- 4bigger Allen bolts (11+10) in the headboard (HB);
- 4smaller Allen bolts (4+10) in the footboard (FB);
- 4bigger rounded head bolts (5+13+7) in the mattress support
(MS);
- 4smaller rounded head bolts (6+13) in the stabilizing bars
(SB);
STEP 4 (FOR BOTH 6501 & 7501) (Two adults are
required to complete this step)
Turn your crib with its feet back on the floor.
Attach the storage pouch supplied to the mattress support
spring using two plastic ties (also supplied). Store this
instruction booklet in the storage pouch for future use.
After completing assembly, your crib should look like the one
depicted on the first page of this manual
WARNING: TO KEEP YOUR BABY SECURE AND
SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT’S VERY IMPORTANT TO COMPLETELY
TIGHTEN ALL 16 BOLTS LISTED IN STEP 3.
WARNING!
COMPLETEL
TIGHTEN!

x
top rail
FB middle
panel
y
FB
y
x
FIGURE B
STEP B (FOR BOTH 6501 & 7501)
Using the supplied Allen wrench (1) completely remove both Allen bolts (x)
(previously mounted in factory) then remove the top rail.
You will find another factory mounted Allen bolts (y), one for each leg of your
footboard. Remove both smaller Allen bolts (y) and then the resulted footboard
middle panel by pulling it upward (see FIGURE B). Please, store the top rail, the
middle panel and the resulted Allen bolts in a proper place, taking care not to
scratch the wood finish.
REQUIRED
WARNING (FOR DAY BED OPTION ONLY):
ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
THE MINIMUM AGE SHALL NOT BE LESS THAN 15
MONTHS AND THE MAXIMUM WEIGHT SHALL NOT
BE GREATER THAN 50LB.
IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
DO NOT THROW THIS INSTRUCTION BOOKLET.
this picture shows how your daybed
should look like after completing STEP F
ASSEMBLY INSTRUCTIONS
FOR DAYBED OPTION
OF YOUR 6501 & 7501 SP & TH
CONVERTIBLE CRIBS
NOTE: THE STYLE OF YOUR CRIB, HEADBOARD OR
OF YOUR MATTRESS SUPPORT MAY VARY FROM
WHAT IS PICTURED IN THE INSTRUCTION SHEET
Europe's Kids Furniture
Furniture
4300 Northlake Ct, Ste E, Charlotte, NC 28216
Phone: [phone] / [email protected]
www.rominafurniture.com

FB
MS
STEP A (FOR BOTH 6501 & 7501) (Two adults are required to
complete this step)
Take your crib and carefully place it on the floor with the footboard (FB) on
top, taking care not to scratch its finish.
Using a Phillips screwdriver (not supplied) remove all 4 smaller rounded
head bolts and washers (6+13) involved in mattress support fixing (MS) then
remove the mattress support.
Remove all four smaller Allen bolts and washers (4+10) used to fix the
footboard (FB).
Take the footboard of your crib and carefully hold it in vertical position, with
its feet on the floor.
REQUIRED
FIGURE A
4+10
4+10
4+10
4+10
6+13
6+13
6+13
6+13
WARNING (FOR DAY BED OPTION ONLY):
ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
THE MINIMUM AGE SHALL NOT BE LESS THAN 15
MONTHS AND THE MAXIMUM WEIGHT SHALL NOT
BE GREATER THAN 50LB.
IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
DO NOT THROW THIS INSTRUCTION BOOKLET.
this picture shows how your daybed
should look like after completing STEP F
ASSEMBLY INSTRUCTIONS
FOR DAYBED OPTION
OF YOUR 6501 & 7501 SP & TH
CONVERTIBLE CRIBS
Europe's Kids Furniture
Furniture
4300 Northlake Ct, Ste E, Charlotte, NC 28216
Phone: [phone] / [email protected]
www.rominafurniture.com
NOTE: THE STYLE OF YOUR CRIB, HEADBOARD OR
OF YOUR MATTRESS SUPPORT MAY VARY FROM
WHAT IS PICTURED IN THE INSTRUCTION SHEET