Romina 15510 User manual

this picture shows how your crib
should look like after completing assembly
WARNING: THE PROPER USE OF THIS CRIB IS IMPORTANT
FOR YOUR BABY’S SAFETY. TO KEEP YOUR BABY SECURE
AND SAFE, AND TO AVOID POTENTIAL INJURY OR DEATH,
CAREFULLY READ AND FAMILIARIZE YOURSELF WITH ALL
WARNINGS, CAUTIONS AND INSTRUCTIONS IN THIS BOOKLET.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE USE.
DO NOT THROW THIS INSTRUCTION BOOKLET!
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
T H E Y C A N C A U S E S U F F O C A T I O N .
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.
Europe's Kids Furniture
Furniture
4300 Northlake Ct, Ste E, Charlotte, NC 28216
Phone: [phone] / [email protected]
www.rominafurniture.com
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISION
AND BY THE AMERICAN SOCIETY FOR
TESTING AND MATERIALS
ASSEMBLY INSTRUCTIONS FOR
UPTOWN 15510 STATIONARY CRIB

GENERAL FURNITURE CARE TIPS
- Wood, like any natural material is likely to present variations of grain and texture which will result
in slight color variations or richness in the finish. These differences make each Romina Furniture
item as beautiful and unique as you and your baby are.
- To preserve the initial appearance and functionality of your furniture, it is recommended that all fur-
niture items be used in accordance with their intended design.
- Special water-based finishes are used to make this furniture safe for your baby. These finishes
may be more delicate than those used on adult furniture thus requiring careful maintenance.
- Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans'
zippers or buttons will likely damage the finish on your furniture. When placing or retrieving items
onto the furniture, always set them down and pick them up, do not “slide” them. Items placed onto
the horizontal surfaces must be moved/rotated to prevent discoloration in the finish.
- Exposure to extreme variations of environmental conditions such as humidity and temperature can
fect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35
– 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
- Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture
causing the finish to peel and the wood to warp.
- Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period
of time, they can cause the finish to turn white or discolor. Alcohol or solvent containing substances
or materials will permanently damage the finish.
- In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster
and smoothness of the finish and in most cases may cause hairline cracks in the finish. White finish-
es will yellow naturally over time; exposure to direct sunlight will accelerate this natural process.
Please note that all wood essences will darken over time along with the natural aging process which
is not considered to be quality defect.
- To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not
allow water to stay in contact with the finish as it will damage the finish.
- If you need to put your furniture into storage for any period of time, avoid placing it in damp base-
ments or hot attics. Air flow around and under the furniture should be allowed. Do not place furniture
too close to walls, do not stack anything on it and do not cover it entirely.
- When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt un-
derneath. Certain plastics have ingredients that can react with and damage the finish. It is recom-
mended to rotate the changing pad's position frequently to avoid finish discoloration.

15510 BOX CONTENT
Note: The letters which
identifiy a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
asked to do this.
distributor. Thank you.
Note: During the assembly process whenever using screws or
bolts, check each by placing the screw / bolt on the hardware
diagram which is drawn in actual size. Be sure to use the proper
size and shape specified in the instructions. Be sure to
COMPLETELY TIGHTEN the screws / bolts when you are
Note: The item number of your product is
located on the inner side of the left panel,
on a black and white label. Please, refer to
this number in the event that you need to
call ROMINA FURNITURE or your local
EP
EP
SS
SS
BF
DL
MS
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET
printed in full size
1
3
4
5
6
Please locate and confirm that
you have the following parts:
EP. end panel = 2
SS. stationary side = 2
BF. bottom frame = 1
MS. mattress support = 1
DL. decorative leg = 2
and one bag of hardware with the following:
1. bigger Allen wrench = 1
2. one storage pouch and two plastic ties
3. Allen bolt (40mm - 1 5/8") = 20
4.
5.
6.
rounded head bolt (15mm - 19/32") = 4
“internal star” lock washer = 20
“external star” lock washer = 4
Required tools: Allen wrench (supplied), Phillips
screwdriver (not included), flat screwdriver (not
included).
CAUTION: Do not use a power screwdriver which can
cause screws to break or strip.
Phillips screwdriver (not included)

FIGURE 1
STEP 1 (Two adults are required to complete this step)
Attach the stationary sides (SS) to the end panels (EP) using eight Allen bolts (3), eight bigger washers (5)
and theAllen key. Take care to insert the washer between the bolt and the stationary side vertical post!
Do not completely tighten the bolts at this step, you will be asked to do this later.
3+5
3+5
3+5
3+5
3+5
3+5
3+5
3+5
EP
SS
SS
EP
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET
3x 8 5x 8
REQUIRED

FIGURE 2
BF
DL
DL
3+5
3+5
3+5
3+5
3+5
3+5
3+5
3+5
3+5
3+5
3+5
3+5
NOTE: THE STYLE OF YOUR CRIB OR OF YOUR
MATTRESS SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRUCTION SHEET
STEP 2 (Two adults are required to complete this step)
Turn the crib upside down, taking care not to scratch its finish.
Attach the base frame (BF) to the stationary sides (SS) and to the end
panels (EP)using
six Allen bolts (3), six bigger washers(5) and
the Allen key. Take care to insert the washer between the bolt and the
base frame wooden components!
Attach the decorative legs (DL) to the crib using 6Allen bolts (3),
6washers (5) and the Allen key. Take care to insert the washer
between the bolt and the leg!
Completely tighten all 12 Allen bolts (3+5).
Turn the crib in its normal position, taking care not to scratch its finish.
REMINDER
Youhave tocompletely tighten all 12 Allen bolts,distributed as following:
- 6smaller bolts (3+5) in the base frame;
- 6bigger bolts (3+5) in the decorative legs.
WARNING!
COMPLETELY TIGHTEN!
WARNING: TO KEEP YOUR BABY SECURE AND
SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT T O
COMPLETELY TIGHTEN ALL 12 BOLTS LISTED
IN STEP 2.
REQUIRED
3x 6 5x 6 3x 6 5x 6

FIGURE 3
MIDDLE POSITION
LOWEST POSITION
HIGHEST POSITION
HIGHEST POSITION
MIDDLE POSITION
LOWEST POSITION
X
X
X
X
Y
Y
Y
Y
STEP 3 (One adult is required to complete this step)
There are three positions for the mattress support (from
the highest one for a newborn to the lowest one for a
child that is maximum 35" tall - see caution note).
You
must adjust the height of the mattress support
depending of your child height by inserting all
four bolts and nuts (Y) in the same position
(see FIGURE 3).
Do
The mattress support will come assembled in the
LOWEST POSITION.
Bolt (X) and (Y) are factory mounted.
not completely tighten the bolts at
this step, you will be asked to do this later
REQUIRED
WARNING!
COMPLETELY TIGHTEN!
A D J U S T I N G T H E H E I G H T O F Y O U R M A T T R E S S S U P P O R T
To adjust the vertical position ofyour mattress support you must remove all four bolts and washers (Y),
loosen all eight bolts (4+6, X) lower the frame and insert the bolts and washers (Y) back into the
corresponding
Completely tighten all bolts.
holes, according to the desired height (see FIGURE 3).
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the bottom frame. Before tighten
the bolts, you must slightly press the mattress support frame to make sure this position is achieved.
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL 12 BOLTS (X), (Y)
& (4+6) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET

FIGURE 4
4+6
4+6
4+6
4+6
MS
X
X
X
Y
Y
Y
WARNING!
COMPLETELY TIGHTEN!
WARNING: TO KEEP YOUR BABY SECURE AND
SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT T O
COMPLETELY TIGHTEN ALL 8 BOLTS LISTED
IN STEP 4.
STEP 4 (Two adults are required to complete this step)
Attach the mattress support (MS) to the bottom frame (BF) using
four rounded head bolts (4), four smaller washers (6) and
a Phillips screwdriver (not supplied). The lock washer must be
attached to the bolt before inserting the bolt through the metallic
bracket of the mattress support.
Completely tighten all 12 bolts (X, Y, 4+6) involved in mattress
support fixing using a Phillips screwdriver (not supplied).
REMINDER
You have to completely tighten 12 rounded head bolts, distributed
as following:
- 8bolts (X, Y) in the mattress support;
- 4bolts (4+6) in the bottom frame.
Attach the storage pouch supplied to the mattress support using
two plastic ties (also supplied). Store this instruction booklet in
the storage pouch for future use.
After completing assembly, your crib should look like the one
depicted on the first page of this manual.
NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR
MATTRESS SUPPORT MAY VARY
FROM WHAT IS PICTURED IN THE
INSTRUCTION SHEET
4 x 4 6x 4
REQUIRED

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH OR
REGULAR BED.
*USE OFA VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELLAND FINISH TO PEEL.
*DO NOT STORE CRIB INAREAS WHERE TEMPERATURESAND CONDITIONS ARE EXTREME, SUCH
AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS MAY
CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN STRUCTURAL
FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE MANUFACTURER
WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR CLEANING WITH MILD
SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN A DRY CLOTH, WILL
PRESERVE THE ORIGINAL LUSTERAND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF ACRIB WATER MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING
REGULARLY, BEFORE PLACING THE CHILD IN THE CRIB, THAT
EVERY COMPONENT IS PROPERLYAND SECURELY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT ALL
BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST CHECK
ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS NECESSARY.
PERIODICALLY INSPECT CRIB FOR DAMAGED HARDWARE,
LOOSE JOINTS OR SPLINTERED EDGES.
DO NOT USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR ROMINA FURNITURE FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE TO
HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU MAKE
CONTACT. THE MODEL CODE CAN BE FOUND ON A WHITE LABEL
LOCATED ON THE INSIDE OF YOUR CRIB ON THE SIDE PANEL.
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO YOUR
CRIB!

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of this
fine finish of your Romina Furniture product.
Visit
www.rominafurniture.com
for updates, special offers and more new designs.
Team
Thank you for beeing one of our distinguished clients.
Furniture