Romina 8515 User manual

www.rominafurniture.com

ASSEMBLY INSTRUCTIONS

FOR IMPERIO TWIN & FULL SIZE BEDS

AND CONVERTIBLE CRIBS FULL SIZE BED OPTION

(PLEASE REFER TO “ASSEMBLY INSTRUCTIONS FOR YOUR 8501 CONVERTIBLE CRIBS”)

IMPORTANT:

PLEASE, READ ALL INSTRUCTIONS BEFORE ASSEMBLING!

PLEASE, SAVE INSTRUCTIONS FOR FUTURE USE.

THE STYLE OF YOUR BED / RAILS / ACCESSORIES MAY VARY

FROM WHAT IS PICTURED IN THE INSTRUCTION SHEET

8515 8532

8530 8537

Imperio twin & full beds box content:

HB headboard or tufted headboard = 1

LPFB low profile footboard = 1

BR bed rails = 1 + 1

SL group of support slats

assembled with textile ribbons = 2

HK bed hardware kit = 1

Imperio conversion kit box content:

BR bed rails = 1 + 1

SL group of support slats

assembled with textile ribbons = 2

HK bed hardware kit = 1

Imperio twin & full bed hardware kit:

1. wood screw (35 mm - 1 3/8") = 8

2. Allen bolt (80 mm - 3 1/8”) = 4

3. barrel nut = 4

4. Allen key = 1

5. wooden cap = 8

Phillips screwdriver (not supplied)

Notes:

The letters which identifies a part are the

initials of the respective part name (such

method is employed to facilitate parts

recognition between the drawings and the

parts list).

The item number of your product is located

on a black and white label. Please, refer to

this number in the event that you need to call

ROMINA FURNITURE or your local

distributor. Thank you.

WARNING!

Be sure to COMPLETELY TIGHTEN the

screws / bolts when you are asked to do so.

Required tools:

Allen wrench (supplied), Phillips screwdriver

(not supplied).

CAUTION:

Do not use a power screwdriver which can

cause screws to break or strip SL

Assembly instructions for Imperio twin & full size beds

STEP 1 (Two adults are required to complete this step)

Attach the bed rails (BR) to the headboard (HB) using all four Allen bolts (2) and all four barrel nuts (3). Make sure that the wood brackets attached to the bed rails faces towards the

inside of the bed. Please note that you can choose between two possible height levels for the bed rails. If you intend to use the Romina Furniture bed trundle (BD - purchased

separately) then you must use the upper holes.

Align the straight slots in the head of the barrel nuts horizontally. You can adjust the position of the barrel nut with a flat head screwdriver (not supplied) or a coin.

Push the Allen bolts through the headboard and into the bed rail. Start the thread by hand to assure you don't strip the threads then use the supplied Allen key (4).

Do not completely tighten the bolts at this step, you will be asked to do that later.

STEP 2 (Two adults are required to complete this step)

Insert the metallic hooks attached to the ends of the bed rails into the slots provided in the footboard's legs, so the hooks will catch the inner metallic pins. Make sure that both bed

rails are firmly attached to the footboard.

Completely tighten all four bigger Allen bolts (2).

STEP 3

Place the support slats (SL) onto the wood brackets attached to the bed rails. Position the support slats evenly between the bed ends. Make sure you firmly attach the support slats

to the wood brackets using all eight wood screws (1). Use a Phillips screwdriver (not supplied) to completely tighten the wood screws.

After completing STEP 3, your bed should look like one of the beds depicted on the first page of this instruction booklet.

Assembly instructions for Imperio convertible cribs full size bed option

STEP 1 (Two adults are required to complete this step)

Completely disassemble your crib, taking care not to scratch the wood finish (see STEPS 4 to 1 from “ASSEMBLY INSTRUCTIONS FOR YOUR 8501 CONVERTIBLE CRIB”).

Keep the footboard and the headboard of your crib for the next step and carefully store the other resulted wooden pieces and hardware in a proper place, away from direct sunlight

and moisture, taking care not to scratch the wood finish.

STEP 2 (Two adults are required to complete this step)

Attach the bed rails (BR) to the headboard (HB) of the crib using all four Allen bolts (2) and all four barrel nuts (3). Make sure that the wood brackets attached to the bed rails faces

towards the inside of the bed.

Align the straight slots in the head of the barrel nuts horizontally. You can adjust the position of the barrel nut with a flat head screwdriver (not supplied) or a coin.

Push the Allen bolts through the headboard and into the bed rail. Start the thread by hand to assure you don't strip the threads then use the supplied Allen key (4).

Do not completely tighten the bolts at this step, you will be asked to do that later.

STEP 3

Insert the metallic hooks attached at the ends of the bed rails into the slots provided in the footboard's legs, so the hooks will catch the inner metallic pins. Make sure that both bed

rails are firmly attached to the footboard (FB).

Completely tighten all four Allen bolts.

STEP 4

Place the (SL) onto the wood brackets attached to the bed rails. Position the support slats evenly between the bed ends. Make sure you firmly attach the support slats to support slats

the wood brackets using the all eight wood screws (1). Use a Phillips screwdriver (not supplied) to completely tighten the screws.

Use the wooden caps (5) to cover the holes from the upper part of headboard and footboard’s legs.