2011© Ropam Elektronik s.c.
[email protected] www.ropam.com.pl Installation and operating manual: NEO/NEO PS v.1.4S EN(video camera) VIDEO signal. T e module is equipped wit JPG pictures quality regulation w at enables sending
four pictures via single MMS, 100kB max. Triggering alarm action is done by: VIDEO detection, MGSM inputs
and outputs. T e module enables saving a „frozen picture” onto SD card and its later reading via SMS order.
3.2.2 TS -1: TMEPE ATU E SENSO
Digital temperature sensor wit measurement range from -55°C to +125°C (+/- 1°C).
3.2.3 VS -2 : VOICE SYNTHESIZE
T is module is used to store and reproduce up to 16 radio announcements (8 x 16s + 8x 8s). It can be
additionally linked wit an audio module for listening-in on objects. MSGM 4.0 enables independent summing of
messages coming from a number of recordings (5), in t e event of violating/sabotaging t e input.
3.2.4 VS -1 : VOICE SYNTHESIZE
Module memorizes 20 second voice message.
3.2.5 AM -1: AUDIO MODULE
T e voice module is capable of replaying t e object audio during t e alarm or after establis ing t e
voice message. T e module s ould be connected to t e S-M input.
3.2.6 PS - F: THE BUFFE ED POWE SUPPLY MODULE WITH TWO CHANNEL ADIO CONT OLLE
T e extended PSR version wit built in two c annel radio controller for t e remote control of NEO
(utilizing t e control panel function). PSR-RF as an independent device can functionally replace any two c annel
radio link and a buffered 13.8V DC/1.3A power supply.
4. INSTALLATION
T e NEO/NEO-PS module s ould be installed indoors, w ere air umidity is normal (RH=90% max.
wit out condensation) and temperature in t e range of -10°C to +45°C. W en c oosing place of installation t e
following criteria s ould be taken into account:
- GSM network availability (of t e SIM card operator utilized in t e module),
- t e availability and distance of alarm signal sources and trigger signals (e.g. t e control panel),
- t e availability of power supplies or installation possibility of suc in vicinity,
- the MGSM 4.0 = 10V-14V/1A (min), buffered 13.8V DC power supplies
recommended (e.g. recommended dedicated PS or PS - F)
- the MGSM 4.0-PS = 17V-20V/30VA, (the 17V-20V/AC terminals are used for
connection the secondary winding of mains transformer: O- 2/3, O- H casings)
or DC power supplies recommended 20V-30V/1A min (e.g. PSU 24V DC)
- t e availability of t e premises to t ird parties and susceptibility to sabotage attempts,
- keeping safe distance from sources of potential interference (e.g. buildings, radio transmitters, etc. 230V AC
main power supply lines).
T e NEO/NEO-PS+ module s ould be mounted in a dedicated metal ousing:
- O-R1, O-R2, O-R3, O-R4, O-RH or ot er intended for GSM transmitter or control panel installation:
w en installing t e version wit out ousing,
- information and communication systems via t e DIN 35S bus: w en installing t e version wit ousing for t e
DIN 35S bus (NEO/NEO-PSO-RDIN casing).
4.1. MODULE COMMISSIONNING P OCEDU E
1. T e complete signaling and power supply wiring s ould be implemented.
2. Mount t e ousing and insert t e wiring t roug t e cable glands.
3. Install t e SIM card in t e module:
Insert t e card in t e SIMCARD socket in t e vertical position, wit t e
golden contacts of t e SIM card directed towards t e closer edge of t e
PCB board. T e marker (cut-out) of t e SIM card must be directed
opposite to t e direction of inserting.
4. Install t e module:
a) in t e - O-R1, O-R2, O-R3, O-R4 ousing on t e pins included
in t e kit,
b) in t e GSM transmitter ousings or control panel ousing on
t e self ad esive pins supplied wit t e module,
c) in t e information and communication systems ousing using
t e clip securing t e DIN ousing to t e assembly bus.
5. Connect t e optional additional modules: VSR-2, VSR-1, PSR, PSR-RF, FGR-4, AMR-1
6. Connect t e wires to t e appropriate module connectors.
6
