Rosehill Wine Cellars CALIFORNIA REDWOOD WINERACK User manual

CALIFORNIA REDWOOD WINERACK
BIN AND CASE MODULES
ASSEMBLY &INSTALLATION GUIDE
BORDEAUX BIN /
CARDBOARD CASE F06 (B)
16” x 48”
DIAMOND F05 (B)
32” x 48”
BORDEAUX BIN /
CARDBOARD CASE F06 (A)
16” x 32”
DIAMOND F05 (A)
32” x 32”
BURGUNDY /
BORDEAUX BIN F07 (A)
16” x 32”
BURGUNDY /
BORDEAUX BIN F07 (B)
16” x 48”
CHAMPAGNE /
MAGNUM F08 (A)
16” x 32”
CHAMPAGNE / MAGNUM F08 (B)
16” x 48” WOOD CASE F09 (A)
24”x 32” WOOD CASE F09 (B) 24” x 48”
Rosehill Wine Cellars | Toll Free: 1-888-253-6807
www.rosehillwinecellars.com

TOOLS
COMPONENTS
HARDWARE
1/2” Screw x 12
1 1/4” Screw x 8 Anchor x 8 Nails x 48Bracket x 4
7/8” Screw x 8
Vertical Bar Horizontal Bar (Diamond Slat)
Philips Screwdriver Hammer Level Drill
8”
1”-1 1/8” Finishing Nailer
Highly recommended to prevent splitting of wood. This tool is also
handy for projects around the home.

ASSEMBLE RACK :
Redwood has a variety of natural colours, ranging from red to white. If
consistent colour is important to you, sort the bars before assembly.
Bin and Case modules consist of three racks which are bracketed
together and fastened to a wall. Select pieces of the same colour for
the front, middle, and rear racks and place aside making sure that the
front has the best bars.
Arrange four horizontal bars with the notches up for the rack. Join the
vertical bars to the horizontal bars by interlocking the bars at notches.
IMPORTANT NOTE :
Bin and Case WineRack modules are available in a variety of styles
and sizes. The Diamond, type B (F05) is illustrated in the follow-
ing instructions. Some modules will not have a central vertical bar;
others will have a different number of horizontal bars. The basic
method of construction is the same for all Bin and Case modules.
GETTING STARTED
STEP 1

STEP 2
FASTEN BRACKETS TO REAR
RACK :
Stand rear rack up in standing
position with horizontal bars
facing back. Fasten brackets
to horizontal bars at the posi-
tions shown, with 1/2” screws
though rear holes of brackets.
NOTE : Install bracket under
horizontal bar (gure. A)
NAIL BARS :
Nail at intersections for a good hold ( gure A ) .
Nail through all outer bars into perpendicular bar ends ( gure B ).
Nail two nails at every corner of rack assembly ( gure C ).
B
BA
C
STEP 3
A

STEP 4
B
INSTALLING ANCHORS :
BEFORE ATTACHING TO WALL : For a professional look, install a Base
Trim Kit* before mounting rack to wall. (Shown on last page)
Stand rear rack up against wall where it is to be fastened. Mark through
bracket holes with a pencil where plastic anchors should be installed .
Drill 1/4” holes at the marks (gure A ).
Tap in plastic anchors with hammer ( gure B ).
A
WALL

STEP 5
FASTEN RACK TOGETHER AND TO WALL :
Stand middle rack in position with horizontal bars locked in middle
bracket slot, horizontal bars facing forward. Fasten brackets to bars
with 1/2” screws ( gure A ).
Stand front rack into position, horizontal bar facing forward and fasten
bracket to bars with 1/2” screws ( gure A ).
Set rack assembly to wall lining up bracket holes and wall anchors. Screw
in 1 1/4” screws to fasten brackets to wall ( gure B ).
Insert diamond slat into rack ( gure C ).A
C
B
WALL


7)$4(



!
!!
"
!
""
"
"


The stackable system is available in 2 heightsA(32”) and B (48”) allowing
for the following modularity:
Base / Crown molding and quarter round (optional) can be added to AA and
AB congurations for 8’ ceiling height.
Base / Crown trim addition to BB requires min. 99” ceiling height.
MULTIPLE MODULES
If installing multiple modules, screw adjoining racks together. Fasten
through adjoining bars with 7/8” screws at top, middle and bottom rows,
as shown (Take the diamond slats out for more space).
To avoid cracking, pre-drill 1/16” holes for screws. Fasten through rear
rack sections as well as front. If stacking modules, fasten adjoining
horizontal bars in at least two places. For additional strength and sta-
bility, fasten through bottom horizontal bars into base or oor with 7/8”
screws or nails.
NOTE : All the above congurations assure alignment of modules
Nominal 48” B modules are 47 3/4” to allow for stacking in a nominal
8’ ceiling room.


7)$4(



!
!!
"
!
""
"
"

AA AB BB
*

LIMITED WARRANTY
Drobot Inc warrants this product to be free from defects due to workmanship or
material, under normal use and service, for a period of one (1) year after the date of
purchase. Please call our customer service department at 1-888-274-8813 or e-mail
us at [e-mail]
This warranty does not cover normal cosmetic wear, cosmetic defects, damage
resulting from improper assembly or maintenance, shipping damage, accident, or any
misuse, abuse or use contrary to the written instructions. This product is not war-
ranted for commercial use.
The warranties expressed above constitute the entire warranty of Drobot Inc with
regard to its products and are in lieu of and exclusive of all other warranties, express
or implied, including any of merchantability or tness for a particular purpose. In no
event shall Drobot Inc be liable or responsible for incidental or consequential damages,
including spoilage or breakage of wine. It is your own responsibility to insure your wine,
and to take all reasonable and necessary precautions to safeguard its condition.
© Drobot Inc, 2007
Use of WINERACK is strictly at your own risk. Drobot Inc. will not accept
any responsibility or liability for damages resulting from units not assem-
bled precisely as directed, or not securely fastened to a wall or support
with suitable fasteners.
Before placing any bottles in your WINERACK, test it thoroughly to make
sure all fasteners are secure.
* BASE AND TRIM KIT
Provides a solid base and professional nish for your WineRack project;
The bases come in 3 different lengths 16”,32”,48” and two corner ver-
sions (convex and concave). You can order one directly from Vintage
Keeper or from your dealer.
With base section in place, check for level and adjust with shims as
required. When racks are in place, fasten the lower horizontal bars
directly to Base with screws or nails. Nail moldings to face of base and
racks.
TEST BEFORE USE
v
6
9 "
h
1 /8 "
42)-
ESAB

3()-!32%15)2%$
4/,%6%,
RACK
WALL